Bradley S19-120G User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
Installation
215-148CO Rev. N; ECN 08-512
© 2008 Bradley Corporation
Page 1 of 4 9/11/08
S19-120G
Drench Shower—Cord-Operated
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . 2
Installation Instructions. . . . . . . . . . . . . . . . . . 3
Assembly of Components . . . . . . . . . . . . . . . 4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

2
S19-120G Installation
9/11/08 Bradley Corporation • 215-148CO Rev. N; ECN 08-512
IMPORTANT
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin installation
until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to the
eyewash should be “ON” at all times. Provisions shall be made to prevent unauthorized
shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per ANSI
Z358.1.
The inspection and testing results of this equipment should be recorded weekly to verify
proper operation. This equipment should be inspected annually to ensure compliance
with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment per ANSI
Z358.1.
For questions regarding the operation or installation of this product, visit www.
bradleycorp.com or call 1-800-BRADLEY.
Product warranties and parts information may also be found under ”Products” on our
web site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
P.O.Box309,MenomoneeFalls,WI53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetriebprüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051

3
Installation S19-120G
Bradley Corporation • 215-148CO Rev. N; ECN 08-512 9/11/08
Installation
Supplies Required:
• (3) 3/8" floor anchors and bolts
• Tefon tape and pipe sealant
• Piping to 1-1/4" NPT water supply inlet and
to 1-1/4" NPT drain outlet on unit
• Adequate supply pipe supports
• Min. 4" drain to accommodate 30 gallons
per minute discharge for shower waste
• OPTIONAL: sign-mounting hardware
Step 1: Assemble components
1. Assemble the components as shown on
page 4.
• Apply pipe sealant to all male-threaded
pipe joints.
• Bottom edge of showerhead should be
7'-0" (2134 mm) from the floor.
Step 2: Connect water supply
IMPORTANT: Do not rely on
Bradley’s Drench Shower to support
supply piping.
1. Connect water supply piping to 1" NPT
inlet on unit (piping supplied by installer).
Provide adequate supports (supplied
by installer) for supply pipe using pipe
hangers or other means.
2. Hang the safety sign from the unit with
the curtain hooks provided (or mount it to
the wall using sign-mounting hardware by
installer).
3. Open water supply lines. Test for leaks
and adequate water flow.
15-3/4"
(400mm)
4"
(102mm)
Ø 3.1"
(78.7mm)
24"
(610mm)
7'-0"
(2134mm)
Suggested
Height to
Floor
3'-0"
(914mm)
to Floor
4-1/2"
(114mm)

4
S19-120G Installation
9/11/08 Bradley Corporation • 215-148CO Rev. N; ECN 08-512
1" NPT
Supply Inlet
Assembly of Components
Parts List
1 S19-001VV 1 Self-Closing Spring Assembly
1.1 S19-001V 1 Spring
1.2 S27-286 1 Ball Valve with Jam Nut
1.21 110-214 1 Jam Nut only
1.3 140-720 1 Stop Bracket
1.4 142-002CH 1 Washer
1.5 128-175 1 Handle
2 113-006LK 1 Pipe, 1" NPT x 12"
3 169-847 1 90˚ Elbow 1" NPT
4 S24-188 1 Plastic Showerhead Assembly
4.1 S24-187 1 Flow Control Assembly, 23 GPM
5 151-001 2 Curtain Hook
6 169-860A 1 1/4" Nylon Cord
7 204-421 1 Emergency Inspection Tag
8 114-050 1 Safety Sign
9 269-646 1 “S” Hook
10 269-655 1 Pulley
11 269-765 1 Eye Screw
Item Part No. Qty Description Item Part No. Qty Description
P.O.Box 309, Menomonee Falls,WI 53051
R
TESTTHIS UNIT EACH WEEK
Test-operate valve(s)each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlichim Testbetrieb prüfen, bestätigt
durch Unterschrift.Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnementdes valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne vapas fait
un rapport immédiatement.
P.O.BOX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-050
1.5
1.4
1.3
1.2
5
2
3
7
6
1.1
1.21
4.1
4
8
9
10
11
NOTE: Use
teflon tape
only.