Bradley Express Crescent CRS-2/IR User manual

CRS-2/IR, CRS-3/IR
Express® Crescent®
Lavatory System
CRS-Series
Complies with Texas
Accessibility Standards (TAS)
for Juvenile Height applications.
Installation
Instructions
P.O. Box 309, Menomonee Falls, WI 53052-0309
TEL. 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com
Table of Contents
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . . . . . 3–9
Cleaning and Maintenance . . . . . . . . . . . . . . . . . . . .10
Solenoid Valve Troubleshooting . . . . . . . . . . . . . . .11
Solenoid Valve Repair Parts . . . . . . . . . . . . . . . . . .12
Vernatherm™ Valve Troubleshooting . . . . . . . . . . .13
Vernatherm™ Valve Repair Parts . . . . . . . . . . . . . .14
Cleaning the Strainer . . . . . . . . . . . . . . . . . . . . .13-14
For soap system installation, refer to installation manual
215-1583
NOTE: 3-station unit is shown throughout. 2-station
is similar.
A
D
A
•
C
O
M
P
L
I
A
N
T
IMPORTANT
Read this entire installation manual to ensure proper installation, then
file these instructions with the owner or maintenance department.
Flush all the water supply lines before making connections. Debris in
supply lines will cause the valves to malfunction.
Wall anchors used must have a minimum pull-out rating of 1,000 lbs.
Product warranties may be found under "Product Information" on our
web site at www.bradleycorp.com.
215-1330 Rev. K; EN 06-915
© 2007 Bradley Corporation
Page 1 of 14 2/8/07
TAS
CRS-3/IR/LSD
CRS-2/IR/LSD
UPC
R
C
NAHBNAHB
RESEARCHRESEARCH
CENTERCENTER
C
E
R
T
I
F
I
E
D
P
R
O
D
U
C
T
3
0
1
-
2
4
9
-
4
0
0
0
w
w
w
.
n
a
h
b
r
c
.
o
r
g

Express®Crescent®Lavatory System - CRS-Series
CRS-2/IR, CRS-3/IR Installation Instructions
22/8/07 Bradley Corporation • 215-1330 Rev. K; EN 06-915
Express® Crescent® Lavatory System Dimensions
48"
(1219)
26"
(660)
*34"
(864)
*20"
(508)
*37-3/8"
(949)
8-1/2"
(216)
(mm)
(mm)
(mm)
3-3/8"
(86) 17-3/8"
(441)
14"
(356)
48"
(1219)
26"
(660)
*ADJUSTMENTS TO VERTICAL DIMENSIONS
FOR VARIOUS RIM HEIGHTS
Rim Height Application Adjustment
34" Adult Height ADA, None, as shown
TAS Adult Height
32" TAS Ages 11 thru Subtract 2"
14 or 15, Grades 6
thru 8 or 9
30" TAS Ages 4 thru Subtract 4"
10 or 11, Grades:
Pre-K thru 5 or 6 &
Proposed Juvenile
Height ADA
24" Preschool (required Subtract 10"
by some local
codes)
A
D
A
•
C
O
M
P
L
I
A
N
T

Express®Crescent®Lavatory System - CRS-Series
Installation Instructions CRS-2/IR, CRS-3/IR
3
Bradley Corporation • 215-1330 Rev. K; EN 06-915 2/8/07
Installation Instructions
Supplies required for installation:
• (6) 3/8" wall anchors, bolts and washers to mount bowl to wall (min. pull-out force of 1,000 lbs.)
• 1/2" NPT hot and cold or tempered supply piping
• 1-1/2" drain piping and P-Trap (available from Bradley, p/n 269-1697)
• 110 VAC power source for 110/24 VAC plug-in transformer supplied
• OPTIONAL TRAP COVER: 1/4" wall anchor, bolt and washer to mount trap cover to wall
• OPTIONAL: Bradley recommends installing an electrical cut-off switch to the unit (this feature
prevents accidental water delivery during regular maintenance and service)
Step 1: Rough-ins
NOTE: Refer to Figure 1 below and Figure 2 on page 4 for Express®Crescent®Lavatory System
rough-ins and dimensions.
1. Rough in 1/2" NPT hot and cold supply lines and 1-1/2" NPT drain waste connection through
wall at dimensions shown in Figure 1.
IMPORTANT: Flush all the water supply lines before making connections. Debris in
supply lines will cause the valves to malfunction.
TRAP COVER
(OPTIONAL)
1/2" NPT DRAIN
STUB OUT 2" (51mm)
CENTERLINE
OF FIXTURE
1/2" NPT HOT AND
COLD SUPPLIES
STUB OUT 2" (51mm)
FLOOR
RIM
HEIGHT
34"
(864mm)*
25-5/8"
(651mm)*
6-1/2"
(165mm)
2"
(51mm)
23-3/4"
(603mm)*
Figure 1
*ADJUSTMENTS TO VERTICAL DIMENSIONS FOR VARIOUS RIM HEIGHTS
Rim Height Application Adjustment
34" Adult Height ADA, TAS Adult Height TAS Adult Height None, as shown
32" TAS Ages 11 thru 14 or 15, Grades 6 thru 8 or 9 Subtract 2"
30" TAS Ages 4 thru 10 or 11, Grades: Pre-K thru 5 or 6 Subtract 4"
& Proposed Juvenile Height ADA
24" Preschool (required by some local codes) Subtract 10"
Standard Height Mounting

Express®Crescent®Lavatory System - CRS-Series
CRS-2/IR, CRS-3/IR Installation Instructions
42/8/07 Bradley Corporation • 215-1330 Rev. K; EN 06-915
*ADJUSTMENTS TO VERTICAL DIMENSIONS FOR VARIOUS RIM HEIGHTS
Rim Height Application Adjustment
34" Adult Height ADA, TAS Adult Height TAS Adult Height None, as shown
32" TAS Ages 11 thru 14 or 15, Grades 6 thru 8 or 9 Subtract 2"
30" TAS Ages 4 thru 10 or 11, Grades: Pre-K thru 5 or 6 Subtract 4"
& Proposed Juvenile Height ADA
24" Preschool (required by some local codes) Subtract 10"
Installation Instructions continued . . .
Step 1: Rough-ins cont’d.
2. Install a 110 volt GFI protected electrical outlet per local code at the location shown in Figure 2.
3. Install six 3/8" wall anchors with a minimum pull-out rating of 1,000 lbs. (supplied by installer)
at the locations marked in Figure 2.
4. OPTIONAL TRAP COVER: Install one 1/4" wall anchor at the location marked in Figure 2.
33-1/2"
(851mm)*
31"
(788mm)*
FLOOR
10-1/2"
(267mm)
27-1/4"
(692mm)*
35"
(889mm)*
10"
(254mm)
10"
(254mm)
10"
(254mm)
10"
(254mm)
13-1/2"
(343mm)
13-1/2"
(343mm)
3/8" WALL ANCHORS(6) PLACES, MIN. PULL-OUT
FORCE 1,000 LBS. PER ANCHOR
3-3/4"
(45mm)
22-3/4"
(578mm)*
(4) 1/4" WALL
ANCHORSFOR
OPTIONAL
SOAP SYSTEM
110 volt GFCI PROTECTED
ELECTRICAL OUTLET
(RECOMMENDED LOCATION)
(CHECK LOCAL ELECTRICAL
CODESBEFORE ROUGHING IN)
1-3/8" (35mm)
7-11/16"
(195mm)
OPTIONAL 1/4" WALL
ANCHOR FOR TRAP
COVER (USE TRAP
COVER FOR TEMPLATE) C
L
Figure 2
Standard Height Mounting

Express®Crescent®Lavatory System - CRS-Series
Installation Instructions CRS-2/IR, CRS-3/IR
5
Bradley Corporation • 215-1330 Rev. K; EN 06-915 2/8/07
Installation Instructions continued . . .
Step 3: Install wall anchors
1. Measure and mark the centerline of the lavatory system on the wall.
3. Using cardboard template 186-1311 provided, mark six mounting holes on wall.
3. Drill holes in the wall and install the six 3/8" wall anchors with a minimum pull-out rating of 1,000
lbs. (supplied by installer) at the locations shown in Figure 1 on page 3.
NOTE: The six 3/8" anchors will be used to mount the Crescent® bowl to the wall.
4. OPTIONAL TRAP COVER: Install the 1/4" wall anchor for the Trap Cover (supplied by
installer) as shown on Figure 1. Use Trap Cover to locate.
5. OPTIONAL SOAP TANK: Install 1/4" anchors for soap tank installation (refer to soap system
installation manual #215-1583 for further instructions).
Step 4: Remove cover from bowl assembly
1. Unpack the bowl and cover assembly.
2. Remove the wing nuts on the two threaded rods which retain the cover (see Figure 3).
3. Remove the top cover bracket.
4. Lift the cover off and set aside.
Step 5: Mount the bowl to the wall
WARNING: Do not attempt to install the bowl by yourself. To prevent serious
injury, install the bowl with the assistance of another person and
always use appropriate lifting procedures.
1. With someone to assist you, move the bowl assembly to the wall using appropriate lifting
procedures, secure the bowl to the wall.
2. Level the bowl assembly with shims if necessary and then tighten anchors.
Figure 3
TOP COVER
THREADED ROD
330-078
WING NUT
(161-076)
TOP COVER BRACKET
(140-852)

Installation Instructions continued . . .
Step 6: Install drain spud
1. Assemble the P-trap by (supplied by installer)
connecting the 1-1/2" tubular pipe to the 1-1/4"
tailpiece and to the 1-1/2" drain pipe stubbed out
of the wall (see Figure 4).
Step 7: Connecting Supply
1. Connect the 1/2" NPT female end of the
stop/check valves to the rough-ins.
2. Connect one end of the supply hoses to the
stop/check valves.
IMPORTANT: The hose attached to the hot
water inlet of the Vernatherm™
TMV valve must be connected
to the hot water rough-in.
3. Connect the other end of the supply hoses to the Vernatherm™ TMV valve assembly.
4. OPTIONAL SINGLE-TEMPERED SUPPLY: Attach the stop/check valve to the 1/2" tempered
supply line. Connect the stop/check valve to the solenoid valve with the flexible supply hose.
NOTE: The thermostatic mixing valve requires at least 115° F water from the hot water side for
proper operation. As with all lavatories, there will be a delay in obtaining warm water. If the hot
water is too far away from the washfountain, a circulating pump may be required.
Express®Crescent®Lavatory System - CRS-Series
CRS-2/IR, CRS-3/IR Installation Instructions
62/8/07 Bradley Corporation • 215-1330 Rev. K; EN 06-915
Figure 4
STRAINER
AND
TAILPIECE
269-1584
DRAIN ASSEMBLY
1/4" RUBBER
WASHER
P-TRAP
(polypropylene)
269-1697
FIBER
WASHER
NUT
TRIM TO FIT
Figure 5
VALVE
MOUNTING
BRACKET
FLEXIBLE
SUPPLY HOSE
HOT
SUPPLY
COLD
SUPPLY
STOP/CHECK
VALVE
VERNATHERM™
MIXING VALVE
HOT SUPPLY INLET
VERNATHERM™
MIXING VALVE
COLD SUPPLY INLET

Express®Crescent®Lavatory System - CRS-Series
Installation Instructions CRS-2/IR, CRS-3/IR
7
Bradley Corporation • 215-1330 Rev. K; EN 06-915 2/8/07
Installation Instructions continued . . .
Step 8: Electrical and supply connections
NOTE: Refer to Figure 6a below for CRS-2/IR or Figure 6b on page 8 for CRS-3/IR.
WARNING: The Adaptive® Infrared control must be connected with a 24 VAC
Class II transformer. Connections to 110 VAC will result in damage to
the electronics and can cause personal injury.
CAUTION: Connection of leads other than shown may cause permanent damage
to the sensor.
NOTE: Compliance and conformity to local codes and ordinance is the responsibility of the installer.
NOTE: The solenoid valves have been pre-wired.
1. Snap the senser circuit plug from the bowl into the solenoid circuit plug located on the valve bracket.
2. Snap the transformer circuit plug into the female transformer circuit plug located on the valve bracket.
3. Turn on the water supply to the Express® Crescent® Lavatory System and check for leaks.
4. Plug in the transformer and wait at least two minutes to allow the sensor to adapt to the environment.
5. Pass your hand in front of each station’s sensor until all the air is purged from the lines and water
is flowing smoothly.
NOTE: The Vernatherm mixing valve is NOT factory preset. Upon installation, the temperature of this
valve must be checked and adjusted to ensure delivery of a safe water temperature. Water in excess of
110°F (43°C) may cause scalding.
GREEN SUPPLY TUBE
(FROM SPRAYHEAD) RED SUPPLY TUBE
(FROM SPRAYHEAD)
RED SPADE TERMINAL
GREEN SPADE TERMINAL
SENSOR CIRCUIT PLUG
COMPRESSION NUT
(110-231)
TRANSFORMER
CIRCUIT PLUG
WHITE SPADE TERMINAL
Figure 6a

Installation Instructions continued . . .
Step 8: Electrical and supply connections, cont’d.
6. Check the temperature when approximately 1.0 GPM water flow
is reached and adjust if necessary (the range of the valve is
95°F–115°F (35°C–43°C). To adjust the temperature, follow the
procedure below:
• Loosen temperature locking nut with wrench.
• Using a blade screwdriver, turn the adjustment stem
counterclockwise to increase the temperature or clockwise to
decrease the temperature (see Figure 7).
• Once desired temperature is reached, tighten nut to prevent
temperature change.
Express®Crescent®Lavatory System - CRS-Series
CRS-2/IR, CRS-3/IR Installation Instructions
82/8/07 Bradley Corporation • 215-1330 Rev. K; EN 06-915
Installation Instructions continued . . .
Figure 6b
TRANSFORMER
CIRCUIT PLUG
WHITE SPADE
TERMINALS
BLACK SPADE
TERMINAL
GREEN SPADE
TERMINAL
BLACK SUPPLY TUBE
(FROM SPRAYHEAD)
RED SPADE
TERMINAL
RED SUPPLY TUBE
(FROM SPRAYHEAD)
GREEN SUPPLY TUBE
(FROM SPRAYHEAD)
COMPRESSION
NUT (110-231)
VERNATHERM™
THERMOSTATIC
MIXING VALVE
SENSOR CIRCUIT
PLUG
SUPPLY INLET
TEMPERATURE
ADJUSTMENT
STEM
TEMPERATURE
LOCKING
NUT
Figure 7

Express®Crescent®Lavatory System - CRS-Series
Installation Instructions CRS-2/IR, CRS-3/IR
9
Bradley Corporation • 215-1330 Rev. K; EN 06-915 2/8/07
Installation Instructions continued . . .
Step 9: Install the Optional Soap Dispenser
For Express® Crescent® Lavatory System units with optional soap dispensers, see 215-1583.
Step 10: Install the top cover
1. Carefully place the top cover on top of the lavatory system bowl.
2. Install the threaded rods into the holes on the bottom of the top cover (see Figure 3 on page 5).
3. Slide the anchor plate onto the threaded rods and secure anchor plate against bowl using the
wing nuts provided.
4. OPTIONAL SOAP DISPENSER: Install soap filler assembly in mounting bracket previously
installed. Tighten the optional soap filler cap nut with a spanner wrench.

Express®Crescent®Lavatory System - CRS-Series
CRS-2/IR, CRS-3/IR Installation Instructions
10 2/8/07 Bradley Corporation • 215-1330 Rev. K; EN 06-915
Cleaning and Maintenance Instructions
IMPORTANT: Strong alkaline or acid-based chemicals and cleansers should not be
used to clean the Crescent®. If these chemicals come in contact with
the Terreon® surface, wipe off the surface immediately and flush with
soapy water.
Terreon® and trap cover maintenance
The bowl and top cover are made of Terreon®, a densified solid surface material composed of an
acrylic modified polyester resin. Terreon® is resistant to chemicals, stains, burns and impact. Surface
damage can easily be repairable with everyday cleaners or fine grit abrasives. The trap cover is made
of vacuum-formed ABS plastic and will not chip, peel or flake. With regular cleaning, your Express®
Crescent® will provide years of dependable service.
Trap cover cleaning
IMPORTANT: Do not use abrasive cleansers to clean the trap cover. Abrasive
cleaners can mar the surface.
•Daily cleaning: Wipe the trap cover with a wet cloth, then rinse with water and wipe dry.
•Weekly cleaning: Give the trap cover a thorough cleaning with a liquid tub and tile cleaner to
remove soil and maintain the glossy finish.
•Graffiti/Vandalism: If vandals create markings on the trap cover,
Bradley recommends using Motsenbocker’s LIFT OFF® to remove
ink and spray paint. Remover #3 is for ink and markers, and Remover
#4 is for spray paint. Motsenbocker’s LIFT OFF® can be ordered
through Sanitary Maintenance Service, Inc. (call 1-800-451-5523, ext.
425, or visit www.sanitarymaintenance.com/product.htm for ordering
information). After cleaning with LIFT OFF®, give the trap cover a
final thorough cleaning with a liquid tub and tile cleaner to remove
soil and maintain the glossy finish.
Bowl and cover cleaning
•Daily cleaning: Wipe the unit with a damp cloth and then wipe dry.
•Weekly cleaning: Wipe the surface with a damp cloth and a household liquid detergent. Stubborn
stains can be removed as follows:
1. Using a #7448 Scotch-Brite™ pad, scrub with an abrasive cleanser (such as Ajax®,
Comet® or Soft Scrub®) and water.
2. Clean thoroughly with soapy water and allow to dry.
•Scorch marks: Although Terreon® will not burn, a lit cigarette in contact with Terreon® could
leave a scorch mark. Scorch marks can be removed with either an abrasive cleaner or by buffing
with a #7448 Scotch-Brite™ pad.
•Repair kit: In the unlikely event your Terreon® surface becomes damaged, it can easily and
inexpensively be repaired. Contact your Bradley representative to order a repair kit and be sure
to specify color when ordering.
NOTE: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an
endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products
named are regional in distribution and can be found in local supermarkets, department and hardware
stores or through your cleaning service.
NOTE: It is emphasized that all products should be used in strict accordance with package instructions.
MOTSENBOCKER'S
R