Bradley Verge LVGD Series User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1672 Rev. J; ECN 16-08-008
© 2016 Bradley
Page 1 of 12 6/2/2016
LVGD3
Verge®Lavatory System – LVGD-Series
with Evero®Natural Quartz Material
Table of Contents
Components................................2–3
Supplies Required .............................4
Dimensions ................................4–5
Rough-Ins ...................................6
Frame Mounting...............................7
Faucet Box Mounting ...........................7
Drain Assembly ...............................8
Faucets and Optional Soap Valve .................8
Bowl Mounting ................................9
Strainer and P-trap............................10
Adjust the Temperature ........................10
Trap Cover ..................................11
Cleaning and Maintenance .....................12
WARNING
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation.
Electrical power MUST remain off until installation is complete.
Installer’s hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out
rating of 1,000 lbs.
NOTICE
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file
this manual with the owner or maintenance department. Compliance and conformity to local codes and
ordinances is the responsibility of the installer. Product warranties may be found under “Products” on our
Web site at bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
For standard height mounting, do not exceed the recommended 34" distance from the top of the lav deck
to the finished floor. To meet ADA requirements, the lav deck cannot exceed the 34" maximum height
dimension.

LVGD3 Installation
26/2/2016 Bradley • 215-1672 Rev. J; ECN 16-08-008
Components
Chrome P-trap (S29-094)
Plastic P-trap (269-1697)
Frame
(S17-363)
Access Panel
(186-1816)
Bowl
Contact your Bradley Representative for color options
Complete Hardware Prepack (S45-2473)
Frame Mounting Qty.
Washer, Square 9
Washer, Flat 1" O.D. 2
Bowl-To-Frame (S45-2481) Qty.
Screw, ¼-20 x ½" 3
Washer, Flat ⁵⁄₈" O.D. 3
Trap Cover (S45-2482) Qty.
Screw, 10-24 x ½" 6
#10 Finishing Washer 6
Trap Hook Bracket 1
Screw, 10-24 x 3⁄8" 1
Washer, Flat 35⁄64" O.D. 1
Complete Drain Prepack
(S45-2471)
Strainer and
Screw
(S45-2479)
O-Ring
(125-111)
Drain
Adapter
Packing
Washer
#10-24
Screw
Drain Adapter
Prepack
(S45-2480)
Water supply to battery box solenoid MUST be supplied
using a plastic hose (provided by Bradley).
TMV Valve
(½" NPTM Outlet)
(S45-2478)
Hose Prepack
(S45-2730)
Supply Fittings
(S45-2512)
Supply Fittings
(S45-2513)
Hose Prepack
(S45-2731)
TMV Supply
Connections
Tempered Supply
Connections
Plastic
Hose
Plastic
Hose
Stainless
Steel
Hose
Plastic
Hose
Plastic Hose Stainless
Steel
Hose
Plastic
Hose
Plastic
Hose

Installation LVGD3
Bradley • 215-1672 Rev. J; ECN 16-08-008 6/2/2016 3
Components
IR-DCD Faucet*
(S53-336)
CAP-DCA Faucet
(S53-334)
Battery Box Prepack
(S45-2508)
(includes bracket and
mounting hardware)
Battery Box for
CAP-DCA Faucets
6315-KT0000 Soap Dispenser 6324-68 Soap Dispenser 6334 Soap Dispenser
Optional
Transformer
Plug-In Transformer
Option (PT) for
IR-DCD Faucet
(S53-337)
Plug-in transformer option (PT)
includes Transformer (S53-338),
Adapter (S53-339), and Grounding
Kit (S53-349) for CAP-DCA Faucets
IR-DCG Faucet*
(S53-350)
Plug-In Transformer
Option (PT) for
IR-DCG Faucet
(153-486)
*Adapter S45-2872 included with faucet *Adapter S45-2872 included with faucet

LVGD3 Installation
46/2/2016 Bradley • 215-1672 Rev. J; ECN 16-08-008
Dimensions
Top View
Front View
Supplies Required:
• (11)
3⁄8" lag screws, wall anchors, bolts (minimum pull-out rating of 1,000 lbs.)
• ½" hot/cold or tempered supply piping
• 1½" NPT drain piping
• OPTIONAL: (2) 110 volt GFCI protected electrical outlets for 100–120 VAC plug-in transformers (for Bradley
Faucets)
• Screen filter(s) as needed, if not included with faucet(s)
30"
(762mm)
90" (2286mm)
Top of Deck at Front
30"
(762mm)
66"
(1676mm)
90-7/8" (2308mm)
Bottom of Deck at Front
90-1/2" (2299mm)
Bottom of Deck at Back Wall
89-7/8" (2283mm)
Top of Deck at Back Wall

Installation LVGD3
Bradley • 215-1672 Rev. J; ECN 16-08-008 6/2/2016 5
Dimensions – Side View
33½"
(851mm)
8½"
(216mm)
22½"
(572mm)
15¾"
(400mm)
Standard
Height
Juvenile
Height
TAS, Grades 6
through 8 or 9
TAS, Pre-K
through Grades
5 or 6
301⁄8"
(765mm)
221⁄8"
(562mm)
363⁄8"
(924mm)
14"
(356mm)
30½"
(775mm) 8½"
(216mm)
22½"
(572mm)
15¾"
(400mm)
191⁄8"
(486mm)
333⁄8"
(848mm)
14"
(356mm)
29½"
(749mm) 8½"
(216mm)
22½"
(572mm)
15¾"
(400mm)
261⁄8"
(664mm) 181⁄8"
(460mm)
323⁄8"
(822mm)
14"
(356mm)
271⁄8"
(689mm)
31½"
(800mm) 8½"
(216mm)
22½"
(572mm)
15¾"
(400mm)
281⁄8"
(714mm) 201⁄8"
(511mm)
343⁄8"
(873mm)
14"
(356mm)

LVGD3 Installation
66/2/2016 Bradley • 215-1672 Rev. J; ECN 16-08-008
RIM HEIGHT VERTICAL HEIGHT ADJUSTMENTS FOR CODES A–E and H FIXTURE STYLE
33½" None Standard Height
31½" Subtract 2" TAS, Grades 6 through 8 or 9
29½" Subtract 4" TAS, Pre-K through Grades 5 or 6
30½" Subtract 3" Juvenile Height
Rough-Ins
45" (1143mm) Ref. Dim.
to outside corner of bowl
(mark corner of bowl)
C
L
C
33½"
(851mm)
Ref.
B
A
D
E
26½"
(673mm)
H
427⁄8"
(1089mm)
21"
(533mm)
243⁄8"
(619mm)
B
B
B
B
27"
(686mm)
427⁄8"
(1089mm)
27"
(686mm)
21"
(533mm)
295⁄8"
(752mm)
GFCI Box
4" (102mm)
3" (76mm)
30¼"
(768mm)
343⁄8"
(873mm)
B
B
AB
363⁄8"
(924mm)
Ref.
33¾"
(857mm)
27¼"
(692mm)
24"
(610mm)
10¾" (273mm) 21"
(533mm)
22¼"
(565mm)
B
D
Reinforce wall at points A and B.
Standard rough-in shown.
45½" (1156mm) Ref. Dim.
to outside bottom corner of bowl
CODE DESCRIPTION QTY.
A
3⁄8
" Lav Deck Bowl Anchors with a Minimum Pull-Out Force of 1,000 lbs. (reinforce walls at anchor points) 2
B
3⁄8
" Lav Deck Frame Anchors with a Minimum Pull-Out Force of 1,000 lbs. (reinforce walls at anchor points) 9
H, C ½" Hot/Cold Supplies, Stub-Out 2" From Wall 1
D110v GFI Protected Electrical Outlet (AC version only)
Three single outlets are required for CAP-DCG or CAP-DCA faucets due to the size of the transformers. 3
E1½" NPT Drain, Stub-Out 2" from Wall 1
D
7½"
(191mm)

Installation LVGD3
Bradley • 215-1672 Rev. J; ECN 16-08-008 6/2/2016 7
1Frame Mounting
Typical installation is shown. It may be necessary to repair the wall
after mounting. The fixture may not cover all of the wall modifications.
16"
(406mm)
centers
14"
(356mm)
A
Floor
Drywall
Drain, supplies and electrical box are
shown in their approximate locations.
Cut clearance holes in the plywood as
required.
NOTE: Plywood should equal the
thickness of the drywall (½" minimum).
B
Fasten plywood securely
to at least (4) studs.
A
Use 3⁄8" lag screws and square washers provided to secure
the frame to plywood (9) places. Shim frame as necessary.
NOTE: Other fasteners may be used based on wall material.
D
Shim the frame at anchor points to
ensure the offset bracket is straight.
Leave the top three screws loose.
C
Minimum required to
pick up four studs and
vertical frame members
–56" (1422mm) min.
56"
(1422mm)
Plywood Mounting Height "A" Dimension
Standard Height 207⁄8" (530mm)
TAS, Grades 6 through 8 or 9 187⁄8" (479mm)
TAS, Pre-K through Grades 5 or 6 167⁄8" (429mm)
Juvenile Height 177⁄8" (454mm)
2Faucet Box Mounting
Hang the faucet box brackets onto the frame
in the orientation shown. Piping connection of
box should point toward the back of the unit.
B
Mount the faucet boxes
onto the brackets with
valve positioned toward
the wall (if applicable).
A

LVGD3 Installation
86/2/2016 Bradley • 215-1672 Rev. J; ECN 16-08-008
4Faucets and Optional Soap Valve
For ease of installation, leave the bowl laying on
its back. Install the faucets and optional soap
valves according to manufacturer's instructions.
Bradley Model 6315 Soap Dispenser is shown.
3Drain Assembly
For ease of drain installation, lay the
bowl on its back.
O-Ring
Drain Adapter
Packing Washer
#10-24
Screw

Installation LVGD3
Bradley • 215-1672 Rev. J; ECN 16-08-008 6/2/2016 9
5a Bowl Mounting (to Frame)
Washer
¼"-20
Screw
5b Bowl Mounting (to Wall)
Reinforce behind the wall
at the two bowl mounting
locations, then secure the
bowl to the wall.
A
Press firmly on the back
of the bowl to seat the
bowl into the frame.
Tighten the top three
screws on the frame.
A
Bowl is heavy!
Water supply to battery box solenoid MUST be supplied
using a plastic hose (provided by Bradley).
Cold
Hot
Optional TMV Valve
(½" NPTM Outlet)
Connect faucet hoses. Slide
through keyhole slots from behind.
Optional
Tempered
Supply
TMA Option
NONE Option
Plastic
Hose
Plastic
Hose
Stainless
Steel
Hose
Stainless Steel Hose
Plastic
Hose Plastic
Hose

LVGD3 Installation
10 6/2/2016 Bradley • 215-1672 Rev. J; ECN 16-08-008
Strainer
6Strainer and P-trap
Attach the strainer
screw to the strainer.
Do not overtighten.
A
Thread the strainer screw
through the boss on the
drain adapter and secure
the strainer to the bowl.
B
7Adjust Temperature with Water Running
H
C
ALoosen Cap Screw about 1/4" (4-6 turns)
and lift up cover (do not remove).
BUsing cover, turn cartridge gently until
desired water temperature is reached. Do
not turn past stops as this may damage
unit. Push cover down and tighten screw.
This valve is NOT factory preset.
Upon installation, the temperature
of this valve must be checked and
adjusted to ensure delivery of a
safe water temperature. Water
in excess of 110°F (43°C) may
cause scalding.