Bradley S19-120P User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-148P Rev. R; ECN 17-05-039
© 2017 Bradley
Page 1 of 4 7/18/2017
S19-120P
Drench Shower with Drench Hose
Table of Contents
Pre-Installation Information .............................................................2
Supplies Required...........................................................................3
Assemble components....................................................................3
Connect water supply......................................................................3
Assembly of Components ...............................................................4
Parts List .........................................................................................4

2
S19-120P Installation
7/18/2017 Bradley • 215-148P Rev. R; ECN 17-05-039
WARNING
Flush the water supply lines before beginning installation and after installation is complete. Test
the unit for leaks and adequate water flow. Main water supply to the eyewash should be “ON” at all
times. Provisions shall be made to prevent unauthorized shutoff.
CAUTION
Emergency equipment must be supplied with tepid water (60°F to 100°F/15.6°C to 37.8°C). Any
prolonged exposure to near freezing water affects the body's ability to maintain body temperature,
increasing the risk of hypothermia.
NOTICE
Before installing this product, ensure that there are adequate clearances around the product and
activation of the product does not interfere with other products or obstructions.
Avoid cleaners containing organic solvents, alcohols and hydrocarbons. Rinse with water after
cleaning.
IMPORTANT
The installation and location of all safety drench showers, eye and eye/face washes must comply
with the requirements of ANSI/ISEA Z358.1.
Read this installation manual completely to ensure proper installation, then file it with the owner or
maintenance department. Compliance and conformity to drain requirements and other local codes
and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before discarding any
packaging material. If any parts are missing, do not begin installation until you obtain the missing
parts.
The ANSI/ISEA Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley plumbed
emergency fixtures require a minimum of 30 PSI (0.21MPa) flowing pressure.
Self-closing spring-loaded valves are not UL classified to ANSI/ISEA Z358.1.
Weekly activation must be conducted on all plumbed emergency equipment to ensure a suitable
flushing fluid supply is present and any sediment build-up in the supply line is cleared. Emergency
equipment should be inspected monthly to address any maintenance issues ensuring the
equipment is in good operating condition and that there are no signs of wear.
Workers who may come in contact with potentially hazardous materials should be trained regarding
the placement and proper operation of emergency equipment per ANSI/ISEA Z358.1.
For questions regarding the operation or installation of this product, visit www.bradleycorp.com or
call 800-BRADLEY (272.3539).
Product warranties and parts information may also be found under ”Products” on our web site at
bradleycorp.com.

3
Installation S19-120P
Bradley • 215-148P Rev. R; ECN 17-05-039 7/18/2017
Supplies Required
• Pipe sealant and teflon tape
• Piping to 1" NPT water supply inlet
• Adequate supply pipe supports
• Minimum 4" (102 mm) drain to accommodate
30 gallons (115 liters) per minute discharge for
shower waste
• Sign-mounting hardware
• Backflow prevention device as required by
UPC, IPC and/or local plumbing codes
• OPTIONAL: Hardware to mount bracket to wall
Assemble components
1. Assemble components as shown on page 4.
2. Apply pipe sealant or tape (by installer) to all
male-threaded pipe joints.
3. Bottom edge of showerhead should be 84"
(2134 mm) from the floor.
Connect water supply
NOTICE! Do not rely on Bradley’s Drench Shower
to support supply piping.
1. Connect water supply piping to 1" NPT inlet
on unit (piping supplied by installer). Provide
adequate supports (supplied by installer)
for supply pipe using pipe hangers or other
means.
2. Mount the safety sign to the wall using sign-
mounting hardware supplied by installer.
4½"
(114mm)
9"
(229mm)
Ø 3.1"
(78.7mm)
20"
(508mm)
84"
(2134mm)
Suggested
Height to
Floor
25½"
(648mm)
3⁵⁄₈"
(92mm)
6"
(152mm)

4
S19-120P Installation
7/18/2017 Bradley • 215-148P Rev. R; ECN 17-05-039
Assembly of Components
P.O. BOX 309, MENOMONEE FALLS,WI 53052-0309 USA
TEL: 1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-050
46
5
2
3
1.4
1.2
1.5
1.31
1.3
1
8.1
8.2
11
10
8
9
7
P.O. Box 309, Menomonee Falls,WI 53051
R
TESTTHIS UNIT EACH WEEK
Test-operatevalve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift.Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1STWÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signe en bas.S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
10.1
10.2
10.3
10.1
12
12.4
12.1
12.3
12.2
Parts List
1" NPT
Supply Inlet
Items 1.1–1.5 come preassembled as Item 1.
Items 12.1–12.4 come preassembled as Item 12.
NOTE: Use
teflon tape
only.
Item Part No. Qty. Description
1 S30-059 1 Stay-Open Ball Valve Assembly
1.2 124-048 1 Washer, Friction
1.3 S27-278 1 1" Ball Valve with Jam Nut
1.31 110-214 1 Jam Nut only
1.4 153-489 1 Adapter
1.5 128-201 1 Handle
2 113-006LK 1 Pipe 1" NPT x 12"
3 169-847 1 90° Elbow 1" NPT
4 S24-188 1 Plastic Showerhead Assembly
5 151-001 2 Curtain Hook
6 128-156A 1 Pull Rod
7 204-421 1 Emergency Tag
8 S45-317 1 Hose Fitting Prepack
8.1 113-OO6MJ 1 Pipe Nipple
Item Part No. Qty. Description
8.2 169-880 1 Pipe Tee Reducer
9 114-050 1 Safety Sign
10 S45-831 1 Clip Prepack
10.1 269-681 1 U-Bolt with Nuts
10.2 140-601 1 Bracket - Wall
10.3 142-002BS 2 Lockwasher
11 S89-002 1 Yellow Tube 3/8"
12 S39-817 1 Hand-Held Hose
12.1 S45-2453 1 Service Kit EFW - Black
Sprayheads
12.2 S27-332 1 Valve
12.3 128-182 1 Handle
12.4 S53-063 1 Dust Cover