Bradley S19-220FWPT User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 1-800-BRADLEY FAX [phone]
http://www.bradleycorp.com
Installation
215-1253 Rev. C; EN 06-532G
© 2007 Bradley Corporation
Page 1 of 5 4/30/07
S19-220FWPT
Wall-Mounted Eye/Face Wash
with Plastic Bowl
S19-220TPT
Wall-Mounted Eye/Face Wash
with Stainless Steel Bowl
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . . .2
Installation Instructions . . . . . . . . . . . . . . . . . . . .3
S19-220FWPT Components and Parts List . . . .4
S19-220TPT Components and Parts List . . . . . .5
S19-220FWPT
S19-220TPT

2
S19-220FWPT, S19-220TPT Installation
4/30/07 Bradley Corporation • 215-1253 Rev. C; EN 06-532G
WARNING
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the
installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin
installation until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to
the eyewash should be “ON” at all times. Provisions shall be made to prevent
unauthorized shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per
ANSI Z358.1.
The inspection and testing results of this equipment should be recorded weekly
to verify proper operation. This equipment should be inspected annually to
ensure compliance with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment
per ANSI Z358.1.
For questions regarding the operation or installation of this product, visit
www.bradleycorp.com or call 1-800-BRADLEY.
Product warranties may also be found under ”Product Information” on our web
site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
!
!
!
!
P.O.Box309, MenomoneeFalls, WI 53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX: [phone])
http://www.bradleycorp.com
114-051

3
Installation S19-220FWPT, S19-220TPT
Bradley Corporation • 215-1253 Rev. C; EN 06-532G 4/30/07
Installation
Instructions
NOTE: Flush the water
supply line before
beginning installation.
Supplies Required:
• (3) 3/8" wall fasteners
and bolts
• Pipe sealant
• Piping to 1/2" IPS water
supply inlet on unit
• Piping to 1-1/4" IPS
drain outlet
• Sign-mounting hardware
Step 1: Install inlet
drain fittings
NOTE: Top of eyewash
heads should be 33"-45"
(838mm-1142mm) from
floor.
1. Position the inlet drain
fitting over the 1-1/4"
drain outlet pipe from
wall.
2. Using the inlet drain
fitting as a template,
mark the bolt hole
locations on wall OR
install three suitable
fasteners (supplied by
installer) for 3/8" bolts
in the wall at the
marked hole locations
(see Figure 1).
3. Bolt the inlet drain fitting to the wall or wall fasteners using 3/8" bolts (supplied by installer).
Step 2: Assemble eyewash
1. Assemble eyewash components as shown in Figure 2 on page 4.
• Apply pipe sealant (supplied by installer) to all male-threaded pipe joints.
• Use a strap wrench around pipes when tightening to prevent marring.
Step 3: Connect water supply
1. Connect the water supply piping (supplied by installer) to the 1/2" IPS inlet on the eyewash.
2. Connect the P-trap and the tailpiece to the 1-1/4 IPS drain outlet on the eyewash.
3. Mount the safety sign to a wall or pipe using sign-mounting hardware (supplied by installer).
4. Open the water supply lines. Test for leaks and adequate water flow.
Figure 1

Assembly of Components - S19-220FWPT (Plastic Bowl)
4
S19-220FWPT, S19-220TPT Installation
4/30/07 Bradley Corporation • 215-1253 Rev. C; EN 06-532G
1 S90-097 1 Plastic Eyewash Assembly
1.1 111-061 1 Inlet-Drain Fitting
1.2 124-028 1 Gasket
1.3 154-058 1 Plastic Eyewash Bowl
1.4 173-025 1 Cup Strainer
1.5 113-1150 1 Supply Stem
2 S05-064D 1 Eyewash Head Assembly
2.1 S05-091P 1 Eyewash Yoke
2.2 S05-135 2 Sprayhead Assembly
2.3 S53-063 2 Dust Cover
3 113-006LQ 1 Pipe 1/2" IPS x 3-1/2" Long
4 169-025 1 Elbow 1/2" IPS Street
5 S27-282 1 1/2" Ball Valve with Nut
5.1 110-215 1 Nut only
6 128-135 1 Handle Assembly
7 142-002DA 1 Lockwasher
8 269-167 1 Tailpiece
9 269-142 1 Trap
10 114-051 1 Safety Sign
11 204-421 1 Emergency Tag
Item Part No. Qty Description Item Part No. Qty Description
P.O. B ox 309, Menomonee Falls, WI 53051
R
TESTTHISUNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctionsimmediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift.Jegliche Störungsofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement desvalveschaque semaine et
signe en bas. S'il y à quelque chose qui ne va pasfait
un rapport immédiatement.
P.O. B OX 309, MENOMONEE FALLS,WI 53052-0309USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051
1.5
1.4
1.3
1.2
1.1
3
5
10
7
5.1
6
1/2" IPS
Supply Inlet
11
4
8
1-1/4" IPS
Drain Outlet
1
2.3
2.1
2.2
2
9
NOTE: Items 1.1 -1.5 come presasembled as Item 1.
Items 2.1 -2.3 come preassembled as Item 2.
Figure 2a
Prepack S45-122 includes items 5, 5.1, 6, 7
Prepack S45-123 includes items 5.1, 6, 7

5
Installation S19-220FWPT, S19-220TPT
Bradley Corporation • 215-1253 Rev. C; EN 06-532G 4/30/07
Assembly of Components - S19-220TPT (Stainless Steel Bowl)
1 S90-096 1 Stainless Steel Eyewash Assembly
1.1 111-061 1 Inlet-Drain Fitting
1.2 124-028 1 Gasket
1.3 187-053 1 Stainless Steel Eyewash Bowl
1.4 173-009 1 Cup Strainer
1.5 113-1150 1 Supply Stem
2 S05-064D 1 Eyewash Head Assembly
2.1 S05-091P 1 Eyewash Yoke
2.2 S05-135 2 Sprayhead Assembly
2.3 S53-063 2 Dust Cover
3 113-006LQ 1 Pipe 1/2" IPS x 3-1/2" Long
4 169-025 1 Elbow 1/2" IPS Street
5 S27-282 1 1/2" Ball Valve with Nut
5.1 110-215 1 Nut only
6 128-135 1 Handle Assembly
7 142-002DA 1 Lockwasher
8 269-167 1 Tailpiece
9 269-142 1 Trap
10 114-051 1 Safety Sign
11 204-421 1 Emergency Tag
Item Part No. Qty Description Item Part No. Qty Description
P.O. Box 309, Menomonee Falls, WI 53051
R
TEST THIS UNIT EACH WEEK
Test-operate valve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Test le fonctionnement des valves chaque semaine et
signe en bas. S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
P.O.BOX 309,MENOMONEE FALLS, WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051
1.5 Flow Control
This End
1.4
1.3
1.2
1.1
3
5
10
7
5.1
6
1/2" IPS
Supply Inlet
11
4
8
1-1/4" IPS
Drain Outlet
1
2.3
2.1
2.2
2
9
NOTE: Items 1.1 -1.5 come presasembled as Item 1.
Items 2.1 -2.3 come preassembled as Item 2.
Figure 2b
Prepack S45-122 includes items 5, 5.1, 6, 7
Prepack S45-123 includes items 5.1, 6, 7
Prepack S45-1789 includes items 1.2, 1.4, 1.5