Bradley GLX-3 User manual

Installation
P.O. Box 309
Menomonee Falls, WI 53052 USA
800 BRADLEY (800 272 3539)
[phone]
bradleycorp.com
215-1902 Rev. C: ECO 20-08-028B
© 2021 Bradley
Page 1 of 73 1/21/2021
GLX-3 and TLX-3
Express Lavatory System –
GLX & TLX Series
Système lave-mains Express –
Série GLX et TLX
Sistema de lavabo Express –
Series GLX y TLX
WARNING
Turn OFF electrical power to the electrical outlets, then unplug all electrical units prior to installation.
Electrical power MUST remain off until installation is complete.
Installer’s hardware must be appropriate for wall construction. Wall anchors must have a minimum pull-out
rating of 1,000 lb. NOTICE
Make sure that all water supply lines have been flushed and then completely turned off before beginning
installation. Debris in supply lines can cause valves to malfunction.
IMPORTANT
Read this entire installation manual to ensure proper installation. When finished with the installation, file
this manual with the owner or maintenance department. Compliance and conformity to local codes and
ordinances is the responsibility of the installer. Product warranties may be found under “Products” on our
website at bradleycorp.com.
Separate parts from packaging and make sure all parts are accounted for before discarding any packaging
material. If any parts are missing, do not begin installation until you obtain the missing parts.
For standard height mounting, do not exceed the recommended 33.5" distance from the fixture rim to the
finished floor.
GLX-3 shown with WashBar Duo WBD1
GLX-3 illustré avec WashBar Duo WBD1
Se muestra GLX-3 con WashBar Duo WBD1
TLX-3 shown with Verge™ Soap & Faucet
TLX-3 illustré avec robinet et distributeur de savon Verge™
Se muestra TLX-3 con llave y jabón Verge™

GLX-3 / TLX-3 Installation
21/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Table of Contents
Components .................................................................................................................................................................................... 3
Supplies Required ........................................................................................................................................................................... 4
Dimensions................................................................................................................................................................................ 4–11
Rough-Ins ................................................................................................................................................................................ 12–20
Bracket Mounting........................................................................................................................................................................... 21
Drain Assembly ............................................................................................................................................................................. 22
Verge Soap & Faucet or WashBar Duo Component Assembly..................................................................................................... 22
Bowl Mounting............................................................................................................................................................................... 23
Strainer and P-Trap ....................................................................................................................................................................... 23
Adjust Temperature........................................................................................................................................................................ 24
Access Panel................................................................................................................................................................................. 24
Cleaning and Maintenance............................................................................................................................................................ 25
Table des matières
Composants .................................................................................................................................................................................. 27
Fournitures requises...................................................................................................................................................................... 28
Dimensions...............................................................................................................................................................................28-35
Poses préliminaires .................................................................................................................................................................36-44
Fixation du support........................................................................................................................................................................ 45
Assemblage de l’écoulement......................................................................................................................................................... 46
Assemblage des composants Verge eau et savon ou WashBar Duo ........................................................................................... 46
Montage de la vasque................................................................................................................................................................... 47
Tamis et siphon en P..................................................................................................................................................................... 47
Régler la température.................................................................................................................................................................... 48
Panneau d’accès ........................................................................................................................................................................... 48
Nettoyage et entretien ................................................................................................................................................................... 49
Contenido
Componentes ................................................................................................................................................................................ 51
Materiales necesarios ................................................................................................................................................................... 52
Dimensiones............................................................................................................................................................................ 52–59
Tuberías empotradas................................................................................................................................................................60-68
Montaje de los soportes................................................................................................................................................................ 69
Conjunto de desagüe .................................................................................................................................................................... 70
Conjunto de componentes de llave y jabón Verge o WashBar Duo.............................................................................................. 70
Montaje de la palangana............................................................................................................................................................... 71
Filtro y sifón en P .......................................................................................................................................................................... 71
Ajuste de temperatura ................................................................................................................................................................... 72
Panel de acceso............................................................................................................................................................................ 72
Limpieza y mantenimiento............................................................................................................................................................. 73

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 3
Components
Access Panel
(186-2291)
Bowl
Contact your Bradley Representative
for color options
Individual Rough-In Option
Chrome P-Trap (S29-094)
Plastic P-Trap (269-1697)
Combined Rough-In Option
(GLX only)
Chrome Waste Assembly (S45-2655)
Plastic Waste Assembly (S45-2663)
O-Ring
(125-111)
Drain
Adapter
Packing
Washer
#10-24
Screw
Drain
Adapter
Prepack
(S45-2480)
Prepack
(S45-3008) *Screw
Strainer
Hose Prepack
(S45-2731)
Plastic
Hose
Plastic
Hose
Stainless
Steel
Hose
Plastic
Hose
TMV Valve
(½" NPTM Outlet)
(S45-2701)
Hose Prepack
(S45-2730)
Plastic
Hose
Stainless Steel
Hose
Plastic
Hose
Wall Bracket
(140-1128)
GLX-3
(187-369)
TLX-3
(187-368)
Access Panel
Bracket
(140-1172)
TMV Supply Connections Tempered Supply Connections
Supply Fittings
(S45-3004)
for Verge™ Faucets
S53-3100, S53-3300,
S53-3500, & S53-3700
Supply Fittings
(S45-3005)
for Verge Faucets
S53-3100, S53-3300,
S53-3500, & S53-3700
#10 Access Panel
Thumb Screw
(160-536)
Combined Rough-In Option
(TLX only)
Chrome Waste Assembly (S45-2654)
Plastic Waste Assembly (S45-2662)

GLX-3 / TLX-3 Installation
41/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Dimensions (mm)
Top View – GLX-3 (shown with Verge™ Soap & Faucet)
Front View – GLX-3 (shown with Verge Soap & Faucet)
Supplies Required
• (6) ³⁄₈" fasteners and wall anchors (minimum pull-out rating of 1,000 lb)
• (6) ¼" fasteners (2 for the bowl, 4 for the bracket)
• ½" hot/cold or tempered stub-out(s)
• 1½" NPT drain stub-out(s)
• OPTIONAL: (3) 110V GFCI protected electrical outlets for 100–120 VAC plug-in transformers
• Screen filter(s) as needed, if not included with faucet(s)
20⁵⁄₈"
(525)
42⁵⁄₈" (1084)
28¾" (730) 28¾" (730)
6" (152)
85³⁄₈" (2168)
13⁷⁄₈" (354)
6" (152)
5¹⁄₈" (130)
2⁹⁄₁₆" (65)
19¹⁄₈"
(486)
77⁵⁄₈" (1971)
34"
(864)
Finished Floor

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 5
Dimensions (mm)
Top View – GLX-3 (shown with WBD1)
Front View – GLX-3 (shown with WBD1)
20⁵⁄₈"
(525)
42⁵⁄₈" (1084)
4" (102)
85³/₈" (2168)
13⁷/₈" (354)
5¹⁄₈" (130)
19¹⁄₈"
(486)
77⁵⁄₈" (1971)
7¹⁄₈" (181)
34"
(864)
Finished Floor

GLX-3 / TLX-3 Installation
61/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Dimensions (mm)
Top View – TLX-3 (shown with Verge Soap & Faucet)
Front View – TLX-3 (shown with Verge Soap & Faucet)
20⁵⁄₈"
(525)
42⁵⁄₈" (1083)
6" (152)
85¼" (2166)
15" (381)
6" (152)
5¹⁄₈" (130)
2⁹⁄₁₆" (65)
19¹⁄₈"
(486)
77⁵⁄₈" (1971)
34"
(864)
Finished Floor

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 7
Dimensions (mm)
Top View – TLX-3 (shown with WBD1)
Front View – TLX-3 (shown with WBD1)
20⁵⁄₈"
(525)
42⁵⁄₈" (1083)
27⁵⁄₈" (702) 27⁵⁄₈" (702)
4" (102)
85¼" (2166)
15" (381)
5¹⁄₈" (130)
19¹⁄₈"
(486)
77⁵⁄₈" (1971)
7¹⁄₈" (181)
34"
(864)
Finished Floor

GLX-3 / TLX-3 Installation
81/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Dimensions (mm)
Rim Height Vertical Height Adjustments Fixture Style Notes
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
Side View – GLX-3
Standard Height (ADA) – Verge Faucet
Juvenile Height (ADA) – Verge Faucet
Standard Height (ADA) – WBD1
Juvenile Height (ADA) – WBD1
24"
(610)
31"
(787)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
11¾"
(300)
27"
(686)
34"
(864)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
14¾"
(376)
27"
(686)
24"
(610)
34"
(864)
31"
(787)
6⁷/₈" (175)
6⁷⁄₈" (175)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(276)
10⁷⁄₈"
(276)
14¾"
(376)
11¾"
(300)
7¾"
(196)
7¾"
(196)

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 9
Dimensions (mm)
Side View – GLX-3
CSA Height – Verge Faucet
OBC Height – Verge Faucet
CSA Height – WBD1
OBC Height – WBD1
28⁷⁄₈"
(735)
33¹⁄₈"
(840)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
12⁷⁄₈"
(326)
13⁷⁄₈"
(352)
29⁷₈"
(760)
33⁷⁄₈"
(860)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12⁷⁄₈"
(326)
14⁵⁄₈"
(372)
29⁷⁄₈"
(760)
28⁷⁄₈"
(735)
33⁷⁄₈"
(860)
33¹⁄₈"
(840)
6⁷/₈" (173)
6⁷⁄₈" (173)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(278)
10⁷⁄₈"
(278)
14⁵⁄₈"
(372)
13⁷⁄₈"
(352)
7¾"
(196)
7¾"
(196)

GLX-3 / TLX-3 Installation
10 1/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Dimensions (mm)
Rim Height Vertical Height Adjustments Fixture Style Notes
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
Side View – TLX-3
Standard Height (ADA) – Verge Faucet
Juvenile Height (ADA) – Verge Faucet
Standard Height (ADA) – WBD1
Juvenile Height (ADA) – WBD1
24"
(610)
31"
(787)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
11¾"
(300)
27"
(686)
34"
(864)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
14¾"
(376)
27"
(686)
24"
(610)
34"
(864)
31"
(787)
6¾" (172)
6¾" (172)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(276)
10⁷⁄₈"
(276)
14¾"
(376)
11¾"
(300)
7¾"
(196)
7¾"
(196)

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 11
Dimensions (mm)
Side View – TLX-3
CSA Height – Verge Faucet
OBC Height – Verge Faucet
CSA Height – WBD1
OBC Height – WBD1
28⁷⁄₈"
(735)
33¹⁄₈"
(840)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½"(445)
12¾"
(325)
13⁷⁄₈"
(352)
29⁷₈"
(760)
33⁷⁄₈"
(860)
8⁵⁄₈"
(219)
20⁵⁄₈" (524)
17½" (445)
12¾"
(325)
14⁵⁄₈"
(372)
29⁷⁄₈"
(760)
28⁷⁄₈"
(735)
33⁷⁄₈"
(860)
33¹⁄₈"
(840)
6¾" (172)
6¾" (172)
20⁵⁄₈" (524)
20⁵⁄₈" (524)
17⁵/₈" (448)
17⁵/₈" (448)
10⁷⁄₈"
(278)
14⁵⁄₈"
(372)
13⁷⁄₈"
(352)
7¾"
(196)
7¾"
(196)

GLX-3 / TLX-3 Installation
12 1/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
AInstall (1) ³⁄₈" wall anchor with a minimum pull-out force of 1,000 lb per local codes at locations shown 2
B Install (2) wall anchors per bracket with a minimum pull-out force of 100 lb per local codes at locations shown 6
C Provide structural backing compliant with local building codes. 2
Structural Rough-Ins (mm)
Areas highlighted in gray require sufficient backing
compliant with local building codes.
RIM
HEIGHT VERTICAL HEIGHT ADJUSTMENTS FIXTURE STYLE NOTES
34" No Adjustment Standard ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
31" *Subtract 3" Juvenile ADA & TAS At least one basin must meet dimensional
requirements and have proper reach, knee,
and toe clearance.
26" *Subtract 8" Junior For use by younger children where ADA
guidelines are not a concern.
34"
(864)
31¼"
(794)
C
L
B
A A
B B
Finished Floor
Secure bracket to wall using min. (2) ³⁄₈"
anchor bolts to the left of C/L and min. (2)
³⁄₈" anchor bolts to the right of C/L. The (2)
anchor bolts to the right of C/L must be
min. 16" apart from the anchor bolts to the
left of C/L. When mounting is complete,
check to ensure the bracket is level.
36½" (927)
C
31½"
(801)
28" (711)
37½" (954)
5⁵/₁₆" (135)
5³/₁₆" (131)
16"
(407)
30½"
(775)
¾" (19)
Access Panel
Mounting Bracket

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 13
Plumbing & Electrical Rough-Ins – GLX Individual Waste (mm)
Mounting for Standard ADA and TAS height shown.
Electric outlet locations shown below reflect potential
locations. Refer to the tech data for power supply and
outlet information.
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall, individual waste option 3
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 3
3" (76)
1½" (38)
28" (711) 28¾" (730)
27"
(686)
34"
(864)
28¾" (730)
17½"
(444)
22"
(559)
Finished Floor
A A A
E E E
CH
C
L

GLX-3 / TLX-3 Installation
14 1/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Plumbing and Electrical Rough-Ins – TLX Individual Waste (mm)
Mounting for Standard ADA and TAS height shown.
1½" (38)
3" (76)
28¾" (730) 28" (711)
15" (381) 15" (381)
17½"
(444)
22"
(559)
34"
(864)
26"
(660)
Finished Floor
E E E
A A
C
H
C
L
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall, individual waste option 2
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 3
Electric outlet locations shown below reflect potential
locations. Refer to the tech data for power supply and
outlet information.

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 15
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall, combined waste option 1
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 3
Plumbing & Electrical Rough-Ins – GLX Combined Waste (mm)
Mounting for Standard ADA and TAS height shown.
Combined waste option is not available for use with
WBD1 faucet assembly.
Electric outlet locations shown below reflect potential
locations. Refer to the tech data for power supply and
outlet information.
3¼" (84)
3" (76)
1½" (38)
3¼" (84)
24¼" (616)
8¹⁄₈" (205)20⁵⁄₈" (525)
28¾" (730)
28" (711)
17½"
(444)
22"
(559)
34"
(864)
Finished Floor
Finished Floor
E EE A
C
H
C
L

GLX-3 / TLX-3 Installation
16 1/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Plumbing & Electrical Rough-Ins – TLX Combined Waste (mm)
Mounting for Standard ADA and TAS height shown.
Combined waste option is not available for use with
WBD1 faucet assembly.
Electric outlet locations shown below reflect potential
locations. Refer to the tech data for power supply and
outlet information.
3¼" (84)
3" (76)
1½" (38)
28¾" (730)
28" (711)
17½"
(444)
22"
(559)
34"
(864)
Finished Floor
E EE A
C
H
C
L
CODE DESCRIPTION QTY.
A 1½" NPT Drain, Stub-out 2" from wall, combined waste option 1
H,C ½" Nominal (⁵⁄₈" O.D. Comp.) Hot/Cold supplies, Stub-out 2" from wall 1
E 110V GFI protected electrical outlet (AC faucet and soap only) 3
3¼" (84)
½" (13)
14¼" (368)15¼" (394)
Finished Floor

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 17
Plumbing & Electrical Rough-Ins – Verge Faucet (mm)
Mounting for Standard ADA and TAS height shown.
8"
(203)
9"
(229)
2¹/₈"
(55)
6" (152)
5½"
(139)
34"
(864)
12½"
(318)
23" (584)
16" (406)
7¼" (183)
5¼" (134)
7" (178)
Finished Floor
Mixing Valve
F
F
FF
FF
Faucet Box
(3x)
C
L
CODE DESCRIPTION QTY.
F#10 Anchors for Faucet Control Box Installation
Provide sufficient backing behind the mounting locations. 6

GLX-3 / TLX-3 Installation
18 1/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Plumbing & Electrical Rough-Ins – WBD1 (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
G#10 Anchors for Soap Tank Bracket (100 lb pull out force)
Provide sufficient backing behind the mounting locations. 18
17³⁄₈"
(441)
4¹/₈" (105)
2"
(51)
33" (838) 3½"
(89)
5½" (140)
6½" (165)
6" (152)
34"
(864)
10"
(254)
31" (787)
20½" (521) 21" (533)
4" (102) 4" (102)
5" (127)
30¾" (781) 20¾" (527)
3¼" (83)
8¼" (210)3¾" (95)
Finished Floor
Master Controller
(3x)
Soap Tank
(3x)
C
L
G G G
G
G G GG
GG
GG
G G G G GG
Combined waste option is not available for use with
WBD1 faucet assembly.

Installation GLX-3 / TLX-3
Bradley • 215-1902 Rev. C: ECO 20-08-028B 1/21/2021 19
Rough-Ins – Verge Individual Top-Feed Soap (mm)
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
G#10 Anchors for Soap Tank Installation
Provide sufficient backing behind the mounting locations. 6
5¹/₈"
(131)
32¾" (832) 3¹/₈" (80)
5½" (140)
6³/₈"
(161) 34"
(864)
21¹/₈" (536)
4" (102)
18¼" (464) 24" (610)
19" (483)
Finished Floor
Soap Battery Box
(3x)
C
L
G G GG G G

GLX-3 / TLX-3 Installation
20 1/21/2021 Bradley • 215-1902 Rev. C: ECO 20-08-028B
Rough-Ins – Verge Multi-Feed Soap
Mounting for Standard ADA and TAS height shown.
CODE DESCRIPTION QTY.
G#10 Anchors for Soap Tank Installation
Provide sufficient backing behind the mounting locations. 6
4" (102)
6⁵/₈"
(168) 6³/₈"
(161)
6³/₈" (161)
32¾" (832) 3¹/₈" (80)
5½" (140)
3³/₁₆" (140)
34"
(864)
21¹/₈" (536) 5¹/₈"
(131)
18¼" (464) 24" (610)
30¼" (769)
19" (483)
Finished Floor
Soap Battery
Box (4x)
Multi-Feed
Soap Pump (3x)
Multi-Feed
Tank
C
L
Use Velcro to attach battery box
to front top ledge of the tank.
G
G
G G
G
G
(mm)