Bradley E19-310DC User manual

P.O. Box 309, Menomonee Falls, WI USA 53052-0309
PHONE 800.BRADLEY (800.272.3539) FAX [phone]
bradleycorp.com
Installation
215-163DCE Rev. A; ECN 08-512
© 2008 Bradley Corporation
Page 1 of 5 9/11/08
E19-310DC
Combination Drench Shower
and Eyewash
Table of Contents
Pre-Installation Information . . . . . . . . . . . . . . 2
Installation Instructions. . . . . . . . . . . . . . . . . . 3
Assembly of Components . . . . . . . . . . . . . . . 4
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2
E19-310DC Installation
9/11/08 Bradley Corporation • 215-163DCE Rev. A; ECN 08-512
IMPORTANT
Read this installation manual completely to ensure proper installation, then file it
with the owner or maintenance department. Compliance and conformity to drain
requirements and other local codes and ordinances is the responsibility of the installer.
Separate parts from packaging and make sure all parts are accounted for before
discarding any packaging material. If any parts are missing, do not begin installation
until you obtain the missing parts.
Flush the water supply lines before beginning installation and after installation is
complete. Test the unit for leaks and adequate water flow. Main water supply to the
eyewash should be “ON” at all times. Provisions shall be made to prevent unauthorized
shutoff.
The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a
minimum 0.21 MPa (30 PSI) flowing pressure. Flushing fluid should be tepid per ANSI
Z358.1.
The inspection and testing results of this equipment should be recorded weekly to verify
proper operation. This equipment should be inspected annually to ensure compliance
with ANSI Z358.1.
Workers who may come in contact with potentially hazardous materials should be
trained regarding the placement and proper operation of emergency equipment per ANSI
Z358.1.
For questions regarding the operation or installation of this product, visit www.
bradleycorp.com or call 1-800-BRADLEY.
Product warranties and parts information may also be found under ”Products” on our
web site at www.bradleycorp.com.
Installation
THIS
SIDE
UP
Packing List
•
•
•
•
P.O.Box309,MenomoneeFalls,WI53051
R
TESTTHISUNITEACHWEEK
Test-operatevalve(s) each week and sign below.
Reportany malfunctions immediately.
Ventil(e)wöchentlich im Testbetriebprüfen, bestätigt
durchUnterschrift. Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESESGERÄT1STWÖCHENTLICHZUPRÜFEN.
ESSAIHEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signeen bas. S'il y à quelque chose qui ne va pas fait
unrapport immédiatement.
P.O.BOX309, MENOMONEE FALLS,WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-051

3
Installation E19-310DC
Bradley Corporation • 215-163DCE Rev. A; ECN 08-512 9/11/08
Installation
Supplies Required:
• (3) M10 floor anchors and bolts
• Teflon tape and pipe sealant
• Piping to 1-1/4" BSP water supply inlet and 1-1/4"
BSP drain outlet on unit
• Adequate supply pipe supports
• Minimum 102mm (4") drain to accommodate 115 liters
(30 gallons) per minute discharge for shower waste
• OPTIONAL: sign-mounting hardware
NOTE: Local codes may require the installation
of a backflow prevention valve to complete proper
installation. Compliance with local codes is the
responsibility of the installer. Valve must be tested
annually to verify that it is functioning properly. Backflow
prevention valves are not included with the fixture and
may be supplied by the contractor or purchased from
Bradley Corporation.
Step 1: Secure base to floor
1. Install three suitable anchors (supplied by installer)
for M10 bolts in the floor.
2. Bolt the base to the floor anchors using M10 bolts
(supplied by installer).
Step 2: Assemble components
1. Assemble the remaining unit components as
shown on page 4.
• Apply pipe sealant (by installer) to all male-
threaded pipe joints.
• Use the rubber grip pad provided or a strap
wrench around pipes when tightening to prevent
marring. Place the grip pad on the pipe, then
put the wrench over the grip pad and turn the
pipe with the wrench.
• Bottom edge of the showerhead should be
2159mm (7'-1") from the floor.
Step 3: Connect water supply
IMPORTANT: Do not rely on Bradley’s
Combination Unit to support supply piping.
1. Connect water supply piping to 1-1/4" BSP inlet
on unit (piping by installer). Provide adequate
supports (by installer) for supply pipe using pipe
hangers or other means.
2. Connect drain piping to 1-1/4" BSP drain outlet on
unit (piping by installer).
3. Hang the safety sign from the unit with the curtain
hooks provided (or mount it to the wall using sign-
mounting hardware by installer).
Top View From Bowl
114mm
(4-1/2")
Ø 78.7mm
(3.1")
NOTE: All dimensions assume standard thread
engagement. Variations in manufacturing allow for
+/- 3mm (1/8") per threaded joint. To find the tolerance
of a dimension, add the number of thread joints in
between a dimension and multiply it by 3mm (1/8").
645mm
(25-3/8")
610mm
(24")
2159mm
(7'-1")
to
Floor
1676mm
(66")
to
Floor
140mm
(5-1/2")
1041mm
(41")
152mm
(6")
247mm
(9-3/4")
Ø 273mm
(10-3/4")
267mm
(10-1/2")
Ø229mm (9") Flange
with (3) Ø10mm
(3/8") Holes on Ø
203mm (8") Bolt Circle
229mm
(9")

4
E19-310DC Installation
9/11/08 Bradley Corporation • 215-163DCE Rev. A; ECN 08-512
Assembly of Components
10
P.O.BOX 309,MENOMONEE FALLS, WI 53052-0309 USA
TEL:1-800-BRADLEY FAX:[phone])
http://www.bradleycorp.com
114-052
P.O.Box 309, Menomonee Falls,WI 53051
R
TESTTHIS UNIT EACH WEEK
Test-operatevalve(s) each week and sign below.
Report any malfunctions immediately.
Ventil(e)wöchentlich im Testbetrieb prüfen, bestätigt
durch Unterschrift.Jegliche Störung sofort melden.
Date
Datum
Date
Signed
Unterschrift
Signe
Date
Date
Date Signed
Signed
Signed
DIESES GERÄT1ST WÖCHENTLICH ZU PRÜFEN.
ESSAI HEBDOMADAIRE
Testle fonctionnement des valves chaque semaine et
signe en bas.S'il y à quelque chose qui ne va pas fait
un rapport immédiatement.
22
23
1
2
3
1-1/4" BSP
Drain Outlet
5
2
NOTE: If tee (Item 7) is used as a supply
inlet, use plug (Item 7) on tee (Item 2).
BSP threads this end
HANDLE NOTE:
Close the cover
and put the pin
through the clip
to keep closed.
20
8
13
12
11
6
7
5
1-1/4" BSP Supply Inlet
(BSP threads are noted
with black line on threads)
9
9.5
9.11
9.4
9.2
9.1
9.3
19
16
17
18
Flow
Control
This End
15.1
15.2
15.3
15.4
4.4
4.11
4.3
4.6
4.8
4.7
4.71
4.9
4.10
4.12
4.2
4.1
4.5
4.2
4
4.12
21
14 14.1
NOTE: Items 8.1–8.5 come preassembled as Item 8.
Items 14.1–14.12 come preassembled as Item 14.
NOTE: Use
teflon tape
only.

5
Installation E19-310DC
Bradley Corporation • 215-163DCE Rev. A; ECN 08-512 9/11/08
Parts List
1 131-059 1 Base
2 169-727B 2 Pipe Tee 1-1/4” NPT
3 113-006LC 1 Pipe 1-1/4” NPT x 706 mm
4 S39-226 1 Europe Eyewash Sub-Assy.
4.1 111-039 1 Inlet Drain Fitting
4.2 169-025 2 Street Elbow 1/2” NPT
4.3 S06-136 1 Plgd. Nipple 1-1/4” NPT x 76mm
4.4 169-841 1 Reducing Tee
4.5 142-002DA 1 Lockwasher
4.6 169-726 1 Union 1/2” Female NPT
4.7 S27-282 1 1/2” Ball Valve with Nut
4.71 110-215 1 Jam Nut only
4.8 113-006QX 1 Pipe 1-1/4” NPT x 180mm
4.9 169-764 1 90° Pipe Elbow 1-1/4” NPT
4.10 113-006LE 1 Pipe Nipple 1-1/4” NPT x 76mm
4.11 169-727 1 PIpe Tee 1-1/4” NPT
4.12 113-006LQ 3 Pipe 1/2” NPT x 76mm
5 113-006LW 2 Pipe 1-1/4” NPT x 579 mm
6 169-722B 1 Reducing Tee
7 169-724 1 Pipe Plug 1-1/4” NPT
8 113-006LL 1 Pipe 1” NPT x 234 mm
9 S30-059 1 Stay-Open Ball Valve Assy. 1” NPT
9.1 S27-278 1 1” Ball Valve with Jam Nut
9.11 110-214 1 Jam Nut only
9.2 140-720 1 Stop Bracket
9.3 124-048 1 Washer, Friction
9.4 128-129 1 Handle
9.5 142-002DC 1 Lockwasher
10 128-156A 1 Pull Rod - 24” Long
11 113-006LK 1 Pipe 1” NPT x 310 mm
12 169-847 1 90° Elbow 1” NPT
13 151-001 2 Curtain Hook
14 S24-188 1 Plastic Showerhead Assembly
14.1 S24-187 1 Flow Control Assembly, 23 GPM
15 S45-1782 1 Cup Strainer Prepack
15.1 124-028 1 Center Seal Gasket
15.2 173-009 1 Cup Strainer
15.3 S21-071 1 Stem Pipe Assembly
15.4 113-1159 1 Spacer, Drain
16 S90-009 1 Dust Cover Assembly
17 269-447 1 Bumper
18 161-025 1 Nut
19 S05-091 1 Eyewash Yoke
20 S08-056 1 Handle Assembly
21 153-372R 1 Adapter
22 204-421 1 Emergency Tag
23 114-052E 1 Safety Sign
24 269-915 1 Grip Pad (not shown)
Item Part No. Qty Description Item Part No. Qty Description
Prepack S30-087 includes Items 4.71, 4.5, 20