BrandMotion FLEETWORKS FLTW-7603 User manual

INSTALLATION(INSTRUCTIONS
7603 Instructions 5-29-14.doc Page 1 of 3
Snap-In Lip Mount CMOS Camera with Optional Grid Lines
(Kit # FLTW-7603)
Please read thoroughly before starting installation and check that kit contents are
complete.
Items Included in the Kit:
Tools & Supplies Needed:
Camera
Hole Saw for camera mount
Chassis Harness
Power Harness
These Instructions with Template
¼” Drill Bit (If Needed)
Center Punch
Power Drill
Wire Ties
Electrical Tape or Heat Shrink Tubing
Plastic Trim Removal Tool
Soldering Iron & Solder (Recommended)
Small grommet or Silicone (If needed)
Vehicle service manual (If needed)
Safety Precautions:
•Work in well ventilated area that is clear of obstructions.
•Secure vehicle with tire chucks in both front and rear of tires.
•Turn vehicle accessories OFF and ensure ignition key is in OFF position.
•Wear safety goggles and snug fitting clothes.
•Use tools only for their intended purpose and which are in good repair.
•Only perform this task if confidence, skill, and physical ability permit.
NOTE: We strive to provide accurate and up-to-date installation instructions.
Step 1: Determine Camera location. Place
template in desired position to confirm fitment.
(IMPORTANT: Some states prohibit items blocking
the license plate; check local authorities to confirm
legal status for your application).
Step 2: Mark Camera location with supplied
template, Center Punch the mark, and use
supplied 19mm Hole Saw to drill Camera
mounting hole. NOTE: If your vehicle has a
liftgate panel/ trunk trim cover, it must be
removed.
Step 3: (If necessary) Use a ¼” Drill Bit to
make a pass through hole in any obstructing
panel for the Camera Harness connector.

INSTALLATION(INSTRUCTIONS
7603 Instructions 5-29-14.doc Page 2 of 3
Step 4: Insert connector end of the Camera
Harness through the hole(s) you drilled.
RECOMMENDED: Protect Camera Harness from any
sharp metal edges by applying a small amount of
silicone caulk or a rubber grommet (shown below)
to any area that may come into contact with metal.
Step 5: Route Camera and/ or Chassis
Harness along existing wiring and secure
using Wire Ties or Electrical Tape.
IMPORTANT: Ensure harnesses move freely with
the trunk or liftgate.
Step 6: Connect Camera Harness to supplied
Chassis Harness. The optimal location for this
junction may occur at the top of the liftgate or
inner trunk edge.
Step 7: Route Chassis Harness forward. It
may be necessary to remove sill plates, pillar
covers, side panels, etc. Use a Plastic Trim Removal
Tool to avoid damage to trim pieces.
Step 8: Connect Power Harness male RCA
connector to RCA located on your Display.
Step 9: Using a vehicle specific service
guide/wiring diagram and a multi-meter
verify 12v Ignition or Reverse power source.
Red wire of power harness connects to 12v+
Ignition or Reverse power and Black wire of
power harness to Black chassis ground nut or
wire. RECOMMENDED: Solder wires and cover with
Heat Shrink Tubing or use T-taps as an optional
connection method.
Step 10: Connect Chassis Harness to supplied
Power Harness RCA and power plugs.
Step 11: Use Wire Ties or Electrical Tape to
secure Chassis Harness and Jumper Harness
RCA and power connections.
Step 12:Coil any excess Chassis Harness and
secure it to existing vehicle wiring with Wire
Ties or Electrical Tape.
Step 13: Test system. Close trunk or liftgate and
clear all removed items from around the vehicle
before starting the vehicle. Next, shift into Reverse
and check radio display for the camera image.

INSTALLATION(INSTRUCTIONS
7603 Instructions 5-29-14.doc Page 3 of 3
Step 14: (If necessary) Adjust camera aim.
Reposition camera to the desired viewing angle.
Step 15: Reassemble vehicle. Follow your
disassembly steps in reverse order, taking care not
to bind the harness wiring when reinstalling trim.
(
(
(
(
(
(
(
(
(
(
(
(
(((((((((((((((CAMERA(OPTIONS
The camera offers grid lines or non grid
lines and mirror image or non mirror image
options.
Grid line options: Default setting displays grid
lines. To remove the grid line display, connect
the two green wires near the end of the
Camera Harness.
Display options: Default setting is mirror
image display (i.e., words and letters appear
backwards as in a mirror) for rearward facing
camera (rear view) installation. To change to
non mirror image display for forward
facing camera (front view) connect the two
white wires near the end of the Camera
Harness.
Green and White wires on the Camera Harness.