Bretford MCH-P120C User manual

Attach a 1/2 EMT Screw Connector to each end of the conduit as shown
in FIGURE 1. Slide the conduit-connector assembly onto the electrical
bo es as shown in FIGURE 2. DO NOT FULLY TIGHTEN AT THIS
TIME.
STEP 1
FIGURE 1
FIGURE 2
Chicago Power Channel
Assembly Instructions
CUSTOMER PURCHASED HARDWARE LIST
(QUANTITIES TO BE DETERMINE BY INSTALLER)
4 4 1 9/16 Deep Electrical Bo es
Conduit Appro imately 6 5/8 Long
1/2 EMT Screw Connectors
Combination Coupling EMT to Fle Size 1/2 to 1/2
Conduit Appro imately 19 3/4 Long
1/2 Fle Tubing
4 9/16 Deep Decorator Plates
Decorator Duple Receptacles
Conduit Hangers
MODELS:
MCH-P48C
MCH-P72C
MCH-P96C
MCH-P120C
MCH-P144C
6 5/8 CONDUIT
1/2 EMT SCREW
CONNECTORS
MAKE SURE CONNECTOR SCREWS
FACE THE FLOOR WHEN UNIT IS
ATTACHED TO CHANNEL

NOTE: Remove belly pan by grasping one side and applying pressure outward and downward.

ATTACHMENT
HOLES
Position the bo assembly to the channel using screws provided. Once assembly
is attached to channel, tighten conduit. NOTE: The attachment holes are marked
in FIGURE 3. DO NOT USE THE SMALL THREADED GROUND HOLE FOR
ATTACHMENT.
STEP 2
FIGURE 3
STEP 3
Attach 1/2 conduit hanger to channel appro imately 6 from the end. Using
supplied screws and washers HAND TIGHTEN hanger to channel as shown.
NOTE: TO AVOID STRIPPING SCREW, DO NOT USE POWER TOOLS.
PLACE HANGER 6
FROM END OF
CHANNEL
NOTE: The number of bo assemblies will vary depending on the length of your channel.

STEP 4
Loosely attach a connector to the electrical bo as shown.
STEP 5
Slide a 19 3/4 (appro imately) piece of conduit through hanger and connector.
Tighten hanger and connector. Then wire as needed and install duple es.
SECURE IN PLACE WITH
HARDWARE SUPPLIED
WITH THE HANGER
TIGHTEN ONCE
CONDUIT IS IN PLACE
WARNING: W r ng must be done by a l censed electr c an.
WARNING: L m ted to a max mum of (3) 20 amp c rcu ts per s de.

STEP 6
Install a combination coupling to the end of the
conduit as shown to accept the fle tubing.
NOTE: To connect additional channels together, measure the distance between the
channels, install couplings onto conduit ends and attach fle tubing between the channels.
STEP 7
For your first channel, attach the correct amount of fle tubing
between channel and floor monument. Secure together as shown.
Floor
Monument
Fle Tubing
Conduit

STEP 8
Attach plate covers to electrical bo es as shown.
NOTE: The number of bo es will vary depending
on the length of your channel.

Part # 031-6765
06.07.04 CH
Bretford Bretford Ltd.
11000 Seymour Avenue Technology House
Franklin Park, IL 60131 2 tongate, 110 Windsor Road
T L: 847.678.2545 Slough, Berkshire SL1 2JA ngland
800.521.9614 T L: 01753 53 99 55
FAX: [phone] FAX: [phone]
800.343.1779
www.bretford.com
1) Slide cover plate
up onto box assembly
2) Slide each cover onto
the box assembly until all
pieces are flush.
3) Secure all pieces
together with supplied
screws.
STEP 9
Cover
Attach the covers and plate following the sequence
listed in the above picture.
NOTE: The number of covers and plates will vary
depending on the length of your channel.