Breville Power Blender BLR50 User manual

Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2014.
Due to continued product improvement, the products illustrated/photographed
in this book may vary slightly from the actual product.
BLR50/BBL300 Issue - D14
Australian Customers
Mail: PO Box 22
Botany NSW 2019
AUSTRALIA
Phone: [phone]
Fax: [phone]
Email: Customer Service:
[e-mail]
New Zealand Customers
Mail: Private Bag 94411
Botany Manukau 2163
Auckland NEW ZEALAND
Phone: [phone]
Fax: [phone]
Email: Customer Service:
[e-mail]
Breville Customer Service Centre
www.breville.com.au
www.breville.co.nz

Suits all BLR50 and BBL300 models
the Power Blender™
Instruction Booklet

2
BREVILLE RECOMMENDS SAFETY FIRST
We design and manufacture our products with your safety foremost in
mind. We ask that you exercise a degree of care when using any electrical
appliance and adhere to the following precautions.
READ ALL INSTRUCTIONS
BEFORE USE AND SAVE FOR
FUTURE REFERENCE
• Remove and discard all
packaging materials and
stickers before first use.
• To avoid choking hazard for
young children, remove
and safely dispose the
protective cover fitted on
the power plug.
• This appliance is for
household use only. Do not
use it in moving vehicles or
boats, do not use it outdoors,
and do not use it for anything
other than its intended use.
Misuse can cause injury.
• Keep the appliance and its
cord out of reach of children.
This appliance can be used
by children aged 8 years and
above, and by persons with
reduced physical, sensory
or mental capabilities or
lack of experience and
knowledge if they have
been given supervision or
instruction concerning use of
the appliance in a safe way,
and understand the hazards
involved. Cleaning and
user maintenance shall not
be made by children
without supervision.
• Children shall not play with
the appliance.
• Do not use the appliance
near the edge of a countertop
or table. Ensure the surface
is level, clean and free of
water and other substances.
Please be aware that vibration
during use may cause the
appliance to move.
• Do not use the appliance
on (or close to) a hot gas or
electric burner, or where it
could touch a heated oven
or surface.
• Do not allow the cord to hang
over the edge of a countertop,
or to become knotted.
• To avoid electric shock, do
not immerse the cord, plug or
motor base in water (or other
liquids).
IMPORTANT SAFEGUARDS

3
BREVILLE RECOMMENDS SAFETY FIRST
3
• Installation of a residual
current device (a standard
safety switch on your wall
socket) is recommended to
provide additional safety
protection when using
appliances. It is advisable
that a safety switch (with
a rated residual operating
current not more than
30mA) be installed in the
electrical circuit supplying
the appliance. Contact
your electrician for further
professional advice.
• In order to avoid the possible
hazard of the blender starting
by itself due to inadvertent
resetting of the overload
protector on the motor, do not
attach an external switching
device (such as a timer) or
connect the blender to a
circuit that can regularly
switch the blender on and off.
• Do not operate appliance
with a damaged cord or
plug, or after appliance
malfunctions, or if dropped
or damaged in any way. Stop
use immediately and contact
Breville by phone or email for
replacement or repair.
• Regularly inspect the blade
assembly for damage.
If the blade has become
loose, wobbly or makes
any abnormal noise when
blending, stop using the unit.
Send the product to a Service
Agent for inspection.
• All maintenance (other than
cleaning) is to be done by an
authorised Breville Service
Centre.
• Authorised Breville Service
Centres can be found on
our website
www.Breville.com.au
Alternatively, you can contact
the Breville Customer Care
Centre by phone on
1300 273 845 or email
[e-mail]

4
PAge heAder.....
BREVILLE RECOMMENDS SAFETY FIRST
SAFEGUARDS FOR
YOUR BLENDER
• Wash the blender jug with
warm soapy water before
first use.
• Use only the blender jug
and lid that is supplied with
this blender. The use of
attachments or accessories
not manufactured or
specified by Breville may
cause the risk of fire,
electrical shock, or injury.
• Always ensure the blender
is assembled properly
before using. Lid must be
firmly secured to the jug
before operation to ensure
internal contents do not
escape, spray or overflow.
• If the motor is straining
under a heavy load, do
not operate continuously
for more than 10 seconds.
Allow the motor to rest
for 1 minute between uses
on heavy loads. Note that
none of the recipes in these
instructions are considered
a heavy load.
• Do not leave the blender
unattended when in use.
• Keep hands, fingers, hair
and clothing away from the
blender during use. Always
turn blender off and unplug
at the wall before reaching
inside. Avoid touching
moving parts.
• Be careful when handling
the blender jug as the
blades are very sharp. Be
careful when emptying the
jug and during cleaning.
Mishandling of the blades
may cause injury.
• Do not remove the jug
from the motor base while
blender is in use.
• The blender is intended for
food or drinks preparation.
Do not use for anything
other than food or drinks.
Do not operate without
any ingredients in the
blender jug.
• Never attempt to operate
with damaged blades, or
with utensils, or any
foreign objects inside the
blender jug.
• To reduce the risk of severe
injury to persons or damage
to the blender, keep hands
and utensils out of the jug
while blending.

5
PAge heAder.....
BREVILLE RECOMMENDS SAFETY FIRST
• Never blend hot liquids.
Allow ingredients and
liquids to drop to room
temperature before putting
into the jug for blending.
• Do not put the blender jug
in extremes of heat or cold,
for example placing a cold
jug into hot water, or
vice versa.
• Before moving the blender,
cleaning or putting it away
for storage, always turn
blender off and unplug at
the wall.
• Always disconnect the
appliance from the supply
if it is left unattended
and before assembling,
disassembling or cleaning.
SAVE THESE
INSTRUCTIONS

6
PAge heAder.....
KNOW YOUR BREVILLE PRODUCT
A. Inner measuring cup
B. 1.5 litre glass jug
C. Serrated ice-crushing stainless
steel blades
D. Speed control dial with 5 speeds
and pulse
E. Non-slip feet
A
D
B
E
C

7
OPERATING YOUR BREVILLE PRODUCT
USING THE BLENDER
• Ensure the speed selection dial is in the
‘0’ position. Insert the power cord into a
230/240V power outlet and switch on.
• When using the blender for the first
time, you may notice an odour coming
from the motor. This is normal and will
dissipate with use.
• Remove the lid and add food and/or
liquid into the blender jug. Fill the jug
before placing onto the motor base, to
prevent spillage onto the base.
• Always secure the lid firmly in place
before blending, making sure the inner
cap is also in place.
• Select the desired speed by turning the
speed selection dial clockwise to a speed
setting between 1 and 5. The speed can
be changed at any time during blending.
• Turn the speed selection dial anti-
clockwise to select the pulse/ice setting.
• During the blending process, some
ingredients may stick to the sides of the
blender jug. To push the food back into
the blades, turn the speed selection dial
to the ‘0’ position and switch off at the
power outlet. Remove the lid and use a
plastic spatula to scrape down the sides
of the blender jug. Replace the lid before
recommencing blending.
• At the end of use, always ensure the
speed selection dial is turned to the ‘0’
position. Then switch the appliance
off at the power outlet and unplug the
power cord.
• SPEEDS 1-2: Suitable for savoury dips,
thin batters and soups.
• SPEEDS 3-5: Suitable for smoothies,
cocktails, drinks, sauces and pesto.
• PULSE|ICE: can be used for foods that
require short bursts of power to process
such as herbs, nuts (pesto), small
vegetables and ice. When using the
PULSE|ICE function, hold the blender
lid in place.

8
OPERATING YOUR BREVILLE PRODUCT
DISASSEMBLING BLADES FROM JUG
1. Turn the jug upside down.
2. The inner measuring lid doubles as a
blade assembly tool. Insert the tabs on tool
into the grooves on the blade assembly.
3. Turn the tool anti-clockwise to loosen
the blade assembly.
4. The blade assembly will lift up and out
of the jug.
5. Remove the silicon seal, and keep it safe
for re-assembly.

9
PAge heAder.....
OPERATING YOUR BREVILLE PRODUCT
RE-ASSEMBLING BLADES TO JUG
1. Place the silicone seal onto the narrow
end of the blender jug so that the seal
sits underneath the 3 tabs.
2. Carefully insert the blade assembly.
3. The inner measuring lid doubles as
a blade assembly tool. Insert the tabs
on tool into the grooves on the blade
assembly. Use one hand to hold the
jug handle and the other to turn the
assembly tool clockwise to secure into
place.
4. Turn the tool clockwise to tighten the
blade assembly.