Breville BSB530 User manual

www.breville.com.au
Breville is a registered trademark of Breville Pty. Ltd. A.B.N. 98 000 092 928.
Copyright Breville Pty. Ltd. 2013.
Due to continued product improvement, the products illustrated/photographed
in this brochure may vary slightly from the actual product.
This model number includes a BSB510 Breville Stick Mixer motor unit.
Alternatively any existing Breville BSB510 Stick Mixer motor unit can be used with this Model Pack.
BSB530 Issue - E13
Australian Customers
Mail: PO Box 22
Botany, NSW, 2019
AUSTRALIA
Phone: [phone]
Fax: [phone]
Email: Customer Service:
[e-mail]
New Zealand Customers
Mail: Private Bag 94411
Greenmount, Auckland
NEW ZEALAND
Phone: [phone]
Fax: [phone]
Email: Customer Service:
[e-mail]
Breville Customer Service Centre

TYPESET V1
BSB530
the All In One™
Instruction Booklet

TYPESET V1
CONGRATULATIONS
on the purchase of your Breville product

3
CONTENTS
4Breville recommends safety first
8Know your Breville product
10 Assembly & operation of your
Breville product
21 Care, cleaning & storage of your
Breville product
26 Troubleshooting
28 Food preparation guide
32 Recipes

4
BREVILLE RECOMMENDS SAFETY FIRST
At Breville we are very safety conscious. We design and
manufacture consumer products with the safety of you, our
valued customer, foremost in mind. In addition we ask that you
exercise a degree of care when using any electrical appliance
and adhere to the following precautions.
READ ALL
INSTRUCTIONS
BEFORE USE AND
SAVE FOR FUTURE
REFERENCE
• Remove any packaging
material and promotional
stickers before using the
stick mixer for the first time.
• Do not place the stick mixer
near the edge of a bench
or table during operation.
Ensure the surface is level,
clean and free of water,
flour, etc.
• Do not place the stick mixer
on or near a hot gas or
electric burner, or where it
could touch a heated oven.
• If using the stick mixer
to blend hot food in a
saucepan over heat, remove
the saucepan from the
heat source and ensure
the power cord and body
of appliance are also kept
away from any heat source.
• Take care when handling
the stick mixer, attachments
and sharp cutting blades,
when emptying the bowl
and during cleaning.
Remember the blade and
attachments are very sharp
and should be kept out of
the reach of children.
• Always make sure the stick
mixer is completely and
properly assembled before
operating.
• Ensure the stick mixer is
turned off at the trigger
switch, the power is
switched off at the power
outlet and the cord
is unplugged from the
power outlet before
attempting to attach any
of the accessories.
• Do not use attachments
other than those provided
with the stick mixer.
• Only use the whisk
attachment for the recipes
contained in this instruction
booklet.
IMPORTANT SAFEGUARDS

5
BREVILLE RECOMMENDS SAFETY FIRST
• Do not use the whisk
attachment for anything
other than its intended use.
• Do not attempt to operate
the stick mixer by any
method other than those
described in this booklet.
• Do not process hot or
boiling liquids in food
processor bowl – allow
liquids to cool before
placing into the food
processor bowl.
• Do not operate the
appliance continuously
for more than 1 minute.
Allow the motor to rest for 1
minute between each use.
• Never mix dry, thick or
heavy mixtures for more
than 30 seconds. Stop
the operation and stir
the ingredients before
continuing. Allow the motor
to rest for
1 minute between each use.
• When using heavy loads,
the appliance should not be
operated for more than
30 seconds.
• Always ensure the stick
mixer is turned off, the
power is switched off at the
power outlet and the cord is
unplugged from the power
outlet before attempting to
move the appliance, when
not in use, if left unattended
and before disassembling,
cleaning or storing.
• If food becomes lodged
around the processing
blade or in the blade guard,
release the ON button,
switch the power off at the
power outlet and unplug
the cord. Use a spatula to
dislodge the food. Do not
use fingers as the blades
are sharp.
• Do not remove the stick
mixer from ingredients
during operation. Ensure
the appliance is switched
off and has stopped turning
before removing, to avoid
contact with moving blade
or whisk.
• Do not leave the stick mixer
unattended when in use.
• To protect against electric
shock do not immerse
the motor body, cord or
power plug in water or any
other liquid.
SAVE THESE
INSTRUCTIONS

6
BREVILLE RECOMMENDS SAFETY FIRST
• Keep the appliance clean.
Follow the cleaning
instructions provided in
this book.
• Do not use the stick
mixer/stick blender with
wet hands.
• Do not push food into
the food chute with your
fingers or other utensils.
Always use the food pusher
provided.
• Keep fingers, hands, knives
and other utensils away
from moving blade
and discs.
• Do not place hands or
fingers in the processing
bowl of the food processor
unless the motor,
processing blade, dough
blade or disc has come to
a complete stop. Ensure
the OFF button has been
pressed to switch the motor
off and the appliance is
switched off at the power
outlet and the power cord
is unplugged before
removing the lid from the
processing bowl.
IMPORTANT
SAFEGUARDS FOR
ALL ELECTRICAL
APPLIANCES
• Unwind the cord fully
before use.
• Do not let the cord hang
over the edge of a table or
counter, touch hot surfaces
or become knotted.
• This appliance can be
used by children aged
from 8 years and above
and persons with reduced
physical, sensory or mental
capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the
appliance in a safe way
and understand the
hazards involved.
• Keep the appliance
and its cord out of reach
of children.
• Children shall not play with
the appliance.

7
BREVILLE RECOMMENDS SAFETY FIRST
• It is recommended to
regularly inspect the
appliance. Do not use the
appliance if power supply
cord, plug or appliance
becomes damaged in any
way. Return the entire
appliance to the nearest
authorised Breville service
centre for examination
and/or repair.
• Cleaning and user
maintenance shall not be
made by children without
supervision.
• Any maintenance, other
than cleaning, should be
performed at an authorised
Breville Service Centre.
• This appliance is for
household use only. Do
not use this appliance for
anything other than its
intended use. Do not use in
moving vehicles or boats.
Do not use outdoors.
• The installation of a
residual current device
(safety switch) is
recommended to provide
additional safety protection
when using electrical
appliances. It is advisable
that a safety switch with a
rated residual operating
current not exceeding
30mA be installed in
the electrical circuit
supplying the appliance.
See your electrician for
professional advice.

TYPESET V1
KNOW
your Breville product

9
KNOW YOUR BREVILLE PRODUCT
A. Speed Control Dial
B. Easy Grip Trigger Switch
C. Motor Body
D. Processing Gear Box
E. Clear Lid
F. 1.6L Chopping Bowl
G. Feed Chute
H. Whisk
I. Stainless Steel Blending Leg
J. Detachable Mashing Gear Box
K. Detachable Mashing Leg
L. Quad Blade
M. Variable Slicing Disc
N. Reversible Shredding Disc
O. Storage Base
P. Spindle
NOT SHOWN
Quad Blade Cover
C
E
D
F
IJ H
L
G
A
B
MO NP
K

TYPESET V1
ASSEMBLY & OPERATION
of your Breville product

11
ASSEMBLY & OPERATION
BEFORE FIRST USE
Remove any packaging material and
promotional labels. Remove the blending
leg from the mixer motor body and wash
it in warm soapy water (refer to assembly
instructions in this booklet). Rinse and dry
thoroughly. Ensure no water remains inside
the blending leg to avoid water running into
the motor body when reattached.
Disassemble and wash the chopping blade,
chopper bowl, chopper bowl lid, whisk,
storage lid, and blending jug in warm soapy
water, rinse and dry thoroughly. Ensure no
water remains on the chopper bowl lid or
whisk attachment to avoid water running
into the motor body when reattached.
NOTE
The detachable blending leg,
chopping bowl (without the gearbox),
quad blade, variable masher, whisk
can also be washed in the dishwasher.
The whisk gear box, processor gear
box, masher gear box and motor
body are not dishwasher safe – see
the care and cleaning section of this
booklet for cleaning instructions of
these parts.
This stick mixer is a versatile appliance
that can be attached to:
• The stainless steel blending leg – for use
as a stick mixer.
• The food processor bowl with quad
blade, variable slicing disc, reversible
shredding disc - for use as a mini
food processor.
• The variable mashing leg – for use as
mashing vegetables.
• The whisk attachment – for use as a
hand whisk.
TO ATTACH THE BLENDING LEG
Hold the blending leg with the blades down,
and align the top end of the blending leg
with the corresponding end of the motor
body and push until the blending leg clicks
and locks onto the motor body.
Always ensure blending leg is dry, and no
water left inside, before reattaching.
USING AS A STICK MIXER
Ensure the blending leg is assembled to the
motor body as detailed above.
1. Place food to be processed into a
sufficiently large mixing bowl or
saucepan (do not use the food processor
bowl as this may damage either the stick
mixer or the bowl). The bowl should only
be ½ full or less when blending liquids
or when making a puree of fruit
and/or vegetables.
2. Insert the plug into a 230/240V power
outlet and turn the power on.
3. Turn the dial at the top of motor body,
select a speed from 1 to 15.
NOTE
If selecting a higher speed, it is
recommended that you start on
a slow speed and then increase to
high speed to avoid splattering and
over-processing.

12
ASSEMBLY & OPERATION
4. Place the blending leg as deeply as
possible into the bowl and press the
trigger switch to turn the stick mixer on.
The button must be held for the required
duration of operation.
5. Work through the ingredients in
the bowl with a gentle raising and
lowering motion.
6. Switch off the motor by releasing the
trigger switch.
7. Ensure the motor has completely
stopped before lifting the blender out of
the bowl.
8. When processing has finished, switch
off at the power outlet and remove the
power plug.
TO DETACH THE BLENDING LEG
Ensure the trigger switch is released, the
power is turned off at power point and the
appliance is unplugged. Hold the motor
body with one hand, and using thumb and
finger of the other hand, press on the two
EJECT buttons on either side of the motor
body. Pull the motor body away from the
blending leg to detach.
RECOMMENDATIONS WHEN USING
AS A STICK MIXER
• The stick mixer blends foods and
liquids rapidly, therefore it is easy to
over process. Remember when using the
blending leg to stop the stick mixer and
check food throughout the operation.
• Use caution when blending hot food as it
can splatter.
• The stainless steel blending leg allows
for hot food to be processed directly
in the saucepan. This makes blending
soups and sauces very easy.
• For safety reasons remove saucepan
away from the heat before processing.
• Ensure the body of the appliance and
power cord are kept away from any
heat source.
• When pureeing and blending, cut food
into uniform sizes. This will ensure
smooth and consistent results.
• Warm all liquids to be added to soups
and purees, this will ensure even
blending.
• Do not operate the appliance
continuously for more than 1 minute.
Allow the motor to rest for 1 minute
between each use.
If food becomes lodged around the
processing blade or in the blade guard,
follow the safety instructions below:
1. Release the trigger switch, the power off
at the power outlet and unplug the cord.
2. Use a spatula to carefully dislodge the
food. Do not use fingers as the blades
are sharp.
3. After the food has been removed and
blades are clear, plug the appliance back
into the power supply, switch the power
on and continue blending.

13
ASSEMBLY & OPERATION
USING THE FOOD
PROCESSOR BOWL
ATTACHING GEARBOX TO FOOD
PROCESSING BOWL LID
The gearbox should be placed into the food
processor lid. It should click into place.
To attach the motor, click into place onto
the gearbox.
TO ATTACH THE FOOD
PROCESSING BOWL, FOOD
PROCESSOR ATTACHMENTS
AND LID
1. Remove the food processing bowl from
the storage unit and place onto a bench
ensuring that the surface is clean
and level.
2. Choose one of the following food
processor attachments:
a) Quad blade
b) Adjustable slicer
c) Reversible shredder
3. There is a common spindle that is
used across all of the three food
processor attachments.
WHEN USING THE
REVERSIBLE SHREDDER
1. Place the spindle, into the centre of the
food processing bowl.
CAUTION
Caution should be taken when
handling the shredding disc.

14
ASSEMBLY & OPERATION
2. Holding the reversible shredder disc,
notice that there is a large grater and
small grater, place the side you require
up. Place over the centre of the spindle
and ensure that it is pushed down firmly.
3. Place the lid into position and ensure
that it is on correctly.
WHEN USING THE
ADJUSTABLE SLICER
1. Place the spindle in the centre of the
food processing bowl.
CAUTION
Caution should be taken when
handling the adjustable slicing disc
and ensure that blade is in the storage
or 0 position.
2. The adjustable slicing disc has 18
precise settings. To adjust the settings
hold the adjustable slicing disc by the
edge (on the opposite side to the cutting
blade) with one hand and turn the
rotating collar to the desired setting with
the other hand.
3. Place the adjustable slicing disc onto
the spindle. Ensure that it is pushed
down correctly.

15
ASSEMBLY & OPERATION
4. Place the lid into position and ensure
that it is on correctly.
WHEN USING THE QUAD BLADE
1. Using care, hold the quad blade in one
hand, with the other hand, place the
spindle through the centre of the quad
blade from underneath. The quad should
self-locate at the base of the spindle.
The quad blade will sit loosely on the
spindle but will lock into place during
processing.
CAUTION
Caution should be taken when
handling the quad blade as the blades
are extremely sharp.
2. Place the quad blade and spindle into
the centre of the food processing bowl.
3. Place the lid into position and ensure
that it is on correctly.
4. Once the blade or disc has been
selected for the food processor you can
now process food. Place the food inside
the processing bowl. If using the quad
blade. Do not exceed the maximum
(MAX) marking.
5. Insert the gear box into the lid of the
food processor.
NOTE
Always place the quad blade into the
food processor prior to placing the
food into the food processor. When
using the disc’s adjustable slicer and
reversible shredder these both can
be placed into the food processor
prior to processing food. Some foods,
such as nuts, can stop the quad blade
from engaging the built in safety
mechanism. If you have troubles
closing the lid with ingredients such
as this we advise to load these through
the feed chute.

16
ASSEMBLY & OPERATION
5. When processing has finished switch
off the motor by releasing the trigger
switch, switch off at the power outlet and
remove the power plug.
6. Detach the food processing bowl and lid
(refer to instructions). Remove the lid
from the food processor bowl. Carefully
remove the food processing blades
or quad blade and use a spatula to
scrape off any attached food back into
food processing bowl.
TO DETACH THE FOOD
PROCESSING BOWL AND LID
Ensure the switch is released, power is
turned off at power point and the appliance
is unplugged.
Hold the motor body with one hand and
using thumb and finger of the other hand,
press on the two EJECT buttons on either
side of the motor body. Pull the motor body
away from the chopper bowl lid to detach.
TO USE THE FOOD PROCESSOR
For food preparation tips and recipes refer to
the recipe section of this booklet.
1. Insert the plug into a 230/240V power
outlet and turn the power on.
2. Select a speed between 1–15 on the
speed control dial.
3. Press the trigger switch to turn
the appliance on and start the
processing action.
4. Feed the food through the feed chute
of the food processor, using the food
pusher to push it down.
CAUTION
Only use the small pusher with
the large pusher resting inside the
feed chute.

17
TO DETACH THE GEARBOX
FROM THE LID
• To remove the gearbox grasp
the gearbox and lift up from the
processing lid.
RECOMMENDATIONS WHEN USING
THE STICK MIXER WITH THE FOOD
PROCESSING BOWL
• Do not operate the stick mixer when the
food processing bowl is empty.
• The bottom of the food processing bowl
features a anti-slip rubber rim. This
keeps the food processing bowl stable,
however it is recommended during
processing to hold the motor body with
one hand and the food processing bowl
and lid with the other.
• When processing, cut food into uniform
sizes to ensure quicker, even and more
consistent results.
• The stick mixer blends foods and
liquids rapidly, therefore it is easy to
over process. Remember to check food
throughout the operation.
NOTE
When using the shredding or slicing
disc do not allow the processing bowl
to fill with food beyond the MAX level
indicated. Processing food beyond
this level could damage parts of the
bowl and lid
ASSEMBLY & OPERATION
CAUTION
DO NOT process hard foods such as
coffee, grains or chocolate in lumps, as
damage to the blade may result.
DO NOT process boiling or hot foods in
the food processing bowl.
NEVER remove the blade from the bowl
before food processing is completed.
Processing hard spices will cause the
chopper bowl to become cloudy over
time. Hard spices are best suited to a
spice grinder with a metal bowl.
ASSEMBLY OF THE POTATO
MASHER LEG
Before first use
Remove any packaging material and
promotional labels. Wash blade and two
parts of the mashing leg before use.
CAUTION
Never immerse the motor body or
gearbox in water or any other liquid.
NOTE
If the variable masher leg is already
assembled start from step 3.

18
1. Holding the outer leg and insert the
gearbox making sure ALIGN arrows
are aligned.
2. Hold both outer leg and gearbox firmly
with one hand and insert inner leg until
it clicks and locks into place.
ASSEMBLY & OPERATION
3. Rotate gearbox while holding outer leg
to lock into place until it clicks.
4. Align the mashing leg with the motor
body and push the two parts together
until it clicks.
5. Place blade on underside of the mashing
head. To lock the blade rotate in a
anticlockwise direction. Blade will not
attach if the leg is not attached to the
motor body.

19
ASSEMBLY & OPERATION
TO USE THE POTATO MASHER LEG
For food preparation tips and recipes
refer to the recipes section. Ensure the
potato masher is completely and properly
assembled.
1. Place food to be mashed into a
sufficiently large mixing bowl or
container or in saucepan.
2. Insert the plug into a 230/240V power
outlet and turn the power on.
3. Select the desired setting on the variable
mashing leg: textured, smooth or
creamy.
4. Select a high speed on the speed
control dial.
5. Place the potato masher into food and
press the trigger switch to turn the
masher on.
6. Move the masher through the
ingredients with a gentle raising and
lowering action until desired texture
is achieved.
7. Switch off the motor by releasing the
trigger switch before lifting the masher
out of the bowl. Switch off at the power
outlet and remove the power plug.
TO DETACH THE POTATO
MASHING LEG
1. Ensure the trigger switch is released, the
power is turned off at power point and
the appliance is unplugged.
2. Before removing motor body, remove
masher blade by holding onto the blade
and turning clockwise to unlock.
3. Once blade is removed, hold the motor
body with one hand, and using thumb
and finger of the other hand, press on
the two EJECT buttons on either side
of the motor body. Pull the motor body
away from the masher to detach.
.
NOTE
Mashing blade will not attach/detach
if the leg is not attached to the
motor body.
RECOMMENDATIONS WHEN USING
WITH THE POTATO MASHING LEG
• Release the trigger switch and ensure
the masher has completely stopped
turning before removing the masher
from the food during operation.
• Place the mixing bowl on a damp cloth
during mashing. This will keep the
mixing bowl stable.
USING AS A WHISK
Remove blending leg from motor body
(follow the instructions 'To detach the
blending leg').
1. Align the whisk gear box to the hole in
the underside of the motor body and
push the whisk in until it clicks and
locks into place.