Brildor Craft Express User manual

P á g i n a 1 | 6
Craft Express
Heat Press

2
Technical Details
Product Name
Portable Heat Press Machine
Rated Voltage
220V
110V
Reference
CEHP0708-LB
Rated Frequency
50-60 Hz
Max. Temperature
200°C/ 392°F
Rated Power
1000 w
800 w
Max. Time
999 s
Cable Lenght
2 m
Overview
1- Silicone Mat
2- Tray
3- Heat Platen
4- Middle Cover
5- Top Cover
6- Touchpad
7- Handle
8- Aviation Connector
Instructions for Use
Press (+/-) to switch between
Fahrenheit and Celsius

3
POWER BUTTON
Long press for 5
seconds
· Long press for 5 seconds to turn on the machine.
· Press and hold for another 5 seconds to turn off the
machine.
· Click once to start the countdown.
· Click again to stop the machine.
REDUCE
5 seconds
· Long press for 5 seconds to set the automatic shutdown
time.
SETUP
Click once or for 5
seconds
· Click once to set the temperature. Click again to set the
time.
· Press for 5 seconds to adjust the temperature difference
in the range of 30ºC.
VIBRATION PUMP SETTINGS
· Press the power button to start the countdown, then
press the +/- buttons to adjust the vibration pressure.
TEMPERATURE CONVERSION
· Click to switch between Fahrenheit and Celsius.
REDUCE
POWER
BUTTON
INCREASE
TEMP./TIME

4
Features
1. The machine comes with two motors: a working motor and a spare one. Both motors
operate in the same three vibration modes ("1-1", "1-2" and "1-3"), for motor 1
vibration frequencies, while "2-1", "2-2" and "2-3" correspond to motor 2.
2. Frequency 1-3 or 2-3 is perfect for printing flat items.
3. Press the power button for 3 seconds to turn the machine on or off.
4. Press the power button to start, stop the countdown or for the machine to stop
beeping after printing.
5. Press "+" and "-" buttons in the countdown mode to set the vibration frequency.
6. Use the "Set", "+" and "-" buttons to adjust the temperature and time.
7. Press "+" and "-" simultaneously to switch between °C and °F.
Printing Parameters
No.
Media
Temp.
Time
Vibration
Frequency
Notes
1
Polyester
200°C
60 s
1-3 or 2-3
1. Print the image in mirror mode with
sublimation paper.
2. Make sure buttons and zips do not come
into contact with the press.
3. Fix the image with heat-resistant tape.
2
Ceramic
coaster
180°C
150 s
1-3 or 2-3
1. Print the image in mirror mode with
sublimation paper.
2. Fix the image with heat-resistant tape.
3
Hardboard
coaster
180°C
120 s
1-3 or 2-3
1. Print the image in mirror mode with
sublimation paper.
2. Peel off the top film.
3. Fix the image with heat-resistant tape.
4
Phone case
with
aluminum
insert
180°C
80 s
1-3 or 2-3
1. Print the image in mirror mode with
sublimation paper.
2. Peel off the top film.
3. Fix the image with heat-resistant tape.
5
Adhesive
sequins
180°C
120 s
1-0 or 2-0
(no
vibration)
1. Print the image in mirror mode with
sublimation paper.
2. Flip the sequins with the white side
facing up and peel the film off the back.
3. Place the adhesive on the garment with
the printed image above it, fix with heat-
resistant tape and print.
4. Turn the sequins over immediately after
printing.

5
Safety Instructions
Warning
Please read and follow the following instructions carefully:
oUnplug the machine when moving it from one place to another.
oUnplug the machine when installing any accessories.
oPlace the machine on a flat and stable surface and use it in a ventilated room.
oWear heat-resistant gloves when using the machine.
oDo not use the machine in places with high temperatures.
oDo not use the machine when it cannot work.
oDo not allow children or adults who do not understand this manual to use it.
oDo not disassemble or repair.
oDo not use unsuitable AC power outlets.
oDo not touch the heating plate when the machine is heating up.
Circuit Board Wiring
ELECTRICAL SCHEMATIC DIAGRAM
Main incoming neutral
Heating coil
Main incoming
supply
Heating coil
Motor 1
Motor 2
Host temperature sensor
Heat element sensor

6
everything for personalisation