Brinly DD-1000 User manual

SINCE 1839
SRI
OP-E
liNG INSl:RU liONS
3
T. LIFT TY·PE T
". N
:'10 0
E -DISK
RR
w
We warrant each Brinly Product sold by us to be free
from manufacturing defects in normal service for a period
of one (1) year (~O days for commercial or rental applica-
tion) comrnencinq with the delivery to the original retail
user.
Our
obli'gation under this warranty is expressly limited.
at our option, to the _replacement or repair at Brinly-Hardy
Company, (340 E. Main Street. Louisvill-e. Ky. 40202) of
such part or parts as inspection shall -disclose to have
been defective. This warranty does not apply -to defects
caused by damage or unreasonable _use (including failure
to provide- reascneble and _ necessary maintenance) while
in the possession of the consumer.
WE SHALL NOT BE LIABLE FOR CONSEQUENTIAL-
DAMAGES OF ANY KIND. including' but not limited to:
consequential labor costs or transportation charges in
connection with the replacement or repair of defective
. parts.
ANY IM·PLlED OR STATUTORY WARRANTIES, IN·
- CLUDING ANY WARRANTY OF MERCHANTABILITY OR
- FITNESS FOR A PARTICULAR PU-RPOSE. ARE EX-
PRESSLY LIMITED TO THE DURATION OF THIS WRITTEN
WARRANTY. We make -no other express warranty. nor is
anyone authorized to make any in our behalf. _ This warranty
gives purchasers specificleqet rights and purchasers may also
have other rights which vary from state to state.
'For parts and service. see your loca! deale-r. Use part NAME and NUMBER when ordering. -
BRINL -HAR Y.C
,M'P N-Y-
(877) 728-82?4

ASS·EMBLY:
~~TE .- ',If your Disk, Harrow is -furnished with Frame
Ang'es having SLOTTED holes, use a1/2" flat Washer
between Bolt Heads or 'Nuts and slotted hole.
REFER FIG. 1.
~} Assemble 'Lower Llnk Pins (A) to ,".A" Frame Halves
(8 and
'C)" usin.g 5k" Jam Nuts (D), 51s" Lock Washers
,(E), an.d !k".Hex 'Nuts (F). ~
2) Attach '~A" ,Frame Halves together as shown with
Spacing Plate '(G). Secure with Y2" x
1314" Hex Bolt (H),
V2" Lock Was'her (J), and 112" Hex Nut (K) (in front
holes only),
'FIN'GER TIGHTEN. .
8) FIG. V - Position Frame Assembly (from step 1, fig.
1) to
disk assemblyFlq. IV; as shown ,Fig. V Posltlon
(4) Spacers (A) and (8)
C~p. Washers (F) as shown.
Complete assembly using (4) 1/2" x
4~' Hex Bolts (8),
(4)
1(2" S.A.E. Plain Washers (C), ~(4) -112" 'Lock Washers
(D), "and ·(4) Y2" 'Hex Nuts (E). ~eck and tighten aU
bolts securely and lubricate disk bearings four places.
FIG. II
FIG. I
·,8-_--...
H .. J-K. ",.- t=====:f.-~-----":"'---~
E-F
.0/
, ,.' A
:C-' ---.....r"'7'
-:#----..:lP:lII----..--JL.~
3) Assemble Frame Angles (L) to "A" Frame Assembly
as shown. S'e-cure with V2" x 1%" Hex Bolt (H), V2"
Lock Wa~sher -(J)" and 112'" Hex Nut (K). ,FING'ER
TIGHT,EN.
4) Assemble Frtame Struts (M) to rear holes of' "p.o."
Frame, Secure with Y2" x 1
3A"
Hex Bolts (H), '112" Lock
Was:hers (J), and
112'" 'Hex Nuts (K). FlNG'E_R TIGHTEN.
S)
Sw,ing Frame Struts into' position' shown and as
'semble lower ends to Frame Ang'les {L} using
0/2" X
13~" Hex Bolts (H), 1/2" Lock Wash~rs (J), and 112" Hex
Nuts (K). F'INGER TIGH'TEN ..
<REFER FIG. II AND' FIG. III
(If gang stud; threaded on both ends, is supplied, ,
place
314" 'Hex Nut to short thread end and proceed as'.
follows:) ..
6) Assemble parts to Gang Bolt or Stud" (A) in follow-
ing order: Washer (B), Disk (C), 'Cup Washer (0), Disk
Spacer (E), Cup Washer (D), Disk (C), Cup
Wa~,her (D),
vyashe·r (8), Bearing Hanger (F), wtth Be~ring (<3),
Washer (B), Cup Washer .(0), Disk '(C)~, ·Cup Washer (D),
Disk Spacer (E)~ Cup Washer (D), Disk ... (C), Washer (8),
Hex Nut (H),. and Hex Jam Nut (J)'. With all parts in
place, tighten Hex
Nut (H) securely and lock with Jam
.Nut (J). Disk should rotate free,ly after assembly. Lubrl-
cats bearing with conventlonalqrease gun.
. 7) FIG.
IV, -Position disk garig· assemblies, -Frame
Angles (A) and Weight Trays '(8), as shown in Fig. IV.
(Note - Disks are shown
inthe most commonly used
spacing and 15° cut posltlon). Attach Disk Gangs to
Frame Angles (A) and Weight Trays' (8) using
112'" X
1314" Carr. 80lts (C), 112" Lock Washers (0); 112" ·Hex Nut
fE), 112'" X1 %" Hex Bolts (F), V2" Flat Washers (G); 1/2" .
Lock Washers (D), 'Y2" Hex Nut (E),.1f2" x 2" Carr. Bolts
(H), 112'" Flat Washers (G), 1/2" Lock Washers (D) and
112" Hex Nut '(E). FINGER TI·GHTEN.
- FIG .• III
f;BEARING HAN'GER
...----- ... /
DB \
LUB FITTING

FIG. IV
FRAME ASSEMBLV
PREPARATION OF TRACTOR 3·POINT HITCH
1. With Hitch Linkage in lowered position, adjust low-
er Links until Lower Link Balls are approximately 10"
from ground (Fig. VI).
2. Attach Stabilizer Chains to lower pin position at
Tractor, DO 'NOT TIGHTEN.;' . "
.' 3..Attach Disk to Hitch as shown Fig .. , VU. Secure with
,Spring Pins. . ;~-/
4. Connect Upper Link to Tractor in center hole and to
lower 'hole in Disk Mast. Secure with H"itch and
Pins.
W.ith Hitch in float 'pdsiti·on, adjust Upper
so that front and re'~r Dlsk G.~:n:gs are on ground.
5. Raise Disk with hydraulic I·ift and adjust 'Stabilizer
·:C·hains to prevent stde sway in transport position.
, ·.Dis·k. gangs may be set a:t angles ·of 10° - 1'5° or 200
and moved toqether or apart, For average soil condi ..
tlons, use dlsk with ·gangs set at 15° and spaced as
shown in Assembly Instructions. Disk should run level
when 3
Pt Hltch is pre-adjusted as recommended and
disk blades are running between 2~'-3" 'deep. Start disk-
ing oper-ation at a.slower comfortable speed: tncrease
tractor speed as clods reduce In size. The types of soil,
moisture, and the weight on harrow w·;11 determine how
many times you will have to. 'go 'back and forth to get
the ·kind of seed bed desired. For harder or dryer soils,
addlttonal
weight may be added to improve penetration.
Astandard 8'x 8 x 16 concrete 'block wHI nest in weight
trays on each side of disk. Always operate disk with
hitch hydraulic control lever in lowered float position,
Ridging., sometlmes caused by rear outer disk can
'be reduced or ellrntnated by changing tractor speed,
shortening top
link of 3 Pte Hitch, or acombination of
·both. Always "lift
disk before turning tractor at ends of
field.' . . .
·L·UB:RICATE D·ISK BEARINGS AT LEAST ONCE DAILY.
FIG. VI
........
UPp·ER LINK

18
17,-- _
REPAIR PA,RTS LIST
MODE.l DD-1000 DISK HARROW
BRINLVHARDY COMPANY'
P.O. 'BOX 1,8
JEFFERSONVll~EJ IN.
47131--00"1'8
NOTE- If your I)i,k Harrow is fur~l.hed
Angles having SLOTTED, holel, use II 1IJ"Flat UII •• l'IIlollSlIIJ'
between Bolt Heads.or Nuts and slotted hole.
Ref. Part Descrlptlon Hdwe. Qty. .
Ref~
Part . Description Hdwa.
No. Bag No. Bag
1
8~719-10
Frame, Angle 2 16 D-180-10 ' Disk. Hanger 4
28-720-10 . Frame Strut 217} 0-192-10 Weight Tray Angle '
..
2
3B-724p·01 Lower· Link Pin
'2
2 18 1M1628P Hex
Bolt- 1/2 X 13 .4" 10 10
,4-
8-1361-1"0
HA;' Frame Half - L.H~
1
~9
1M1664P . Hex
Bolt-";' 112
x'4"
4("4
58-1362·..10 "AU Frame Hatf-« A.H. 1·20 10M1628P Carriage
Bolt - 1/2
X1'3A". 6
6,
58-1363-10 Spacing Plate 1 21 .10M1632P' Carriage
Bolt -:- 1/2
x 2'~ .,
',2
2
7
O.:.128P
Grease Fitting 422 ···30M1600P Hex Nut :"-Y2" -13 22 . 22
8D-143P Thrust Washer 16 16 23 30M2000P Hex- Nut -
SAJI' -'1'1 33
9·
0-159-01 Frame Spacer 424 30M2400P. Hex
Nut-%"-10
44
10 0-161-10 . Frame ·Angle.· 225 31M2000P Hex Jam Nut
-- 5fa~',- 11 2 2
1'1
·0-167-02
~earing· Tube 4
.4
26 31M2400P Hex Jam
Nut-%"-10
44
12 D~168P'-01
Centering Washer 32 32 27- 40M1600P, Lock Washer -
1/2" Mad. 23 23
13 D-169pl-01 Disk Spacer 828 40M2000P Lock 'Washer -
%~' .Med. 33
14 D~170P
Gang Bolt.',
429
45M17,1-7P
Plain Washer- 112" S.A.E.
. 24 25
..
'15
0-171-10 '.,Disk Blade -
11" Ora. 16
.' 30 81'760 Disk Blade
-12'~ Dia. (OD-1010)
31 'S-2022P Pin, lower link (DD-1030)·
.32
8-4685
.~oDe~t
L-1033..2