Replace cartridgeReplace cartridge
and turn spindleand turn spindle
anti-clockwiseanti-clockwise
to the maximumto the maximum
temperature.temperature.
Troubleshooting
Symptom Cause Remedy
No flow or
low flow rate
Partially closed isolation valve. Open isolation valve.
Instantaneous water heater cycles on and o
as flow rate or pressure is too low.
Increase water flow rate or
pressure through system.
Head of water is below the
minimum distance required. 2 meters minimum required.
Hot or cold water being drawn o elsewhere
causing pressure changes or instantaneous
boiler temperature changes.
Do not use other water outlets when using the shower.
Airlock or partial blockage in the supply
pipework.
Flush through pipework to ensure removal of debris and
any airlocks.
Water
dripping
from shower
This is normal for a short time after using the
shower.
This is caused by residual water tension, the build up of
water in the shower.
If water continues to drip,
possibly due to the cartridge
Remove cartridge and clean, refer to 'Maintenance' section
before starting any maintenance.
Shower does
not turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
At Bristan, we want to make things as easy as possible for our customers. That’s why we oer solid guarantees on
all our products, eective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register.
For any other queries, please call our Customer Service on 0330 026 6273 where our expert team of advisors
will be able to oer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/guarantees.
4
1
56
Riser Installation (not supplied with AR2 SHXVOFF C)
23
Use the
assembled riser to
mark the
desired
position on the
wall. Remove the
brackets, mark
holes on wall and
drill.
To reduce the build up of limescale and to ensure
this shower works to its maximum performance we
recommend this shower is serviced every 6-12 months
depending on the hardness of your water.
To replace any spare parts for your
shower why not scan the below
QR Code and search for your product.
Spare Parts
Servicing Intervals
9
8
7
6
12
4
3
2
5
Spare Parts
Servicing Intervals
Maintenance - Cartridge Cleaning
1
4
2
1
Turn the shower on, letting
the temperature stabilise.
Temperature Setting 3
Remove O-rings and soak all
components in a suitable solution.
Wash o in clean water. Examine all
seals and replace if needed.
Use WRAS approved silicon based
grease on all seals.
Remove adaptor,
nut and cartridge.
Remove
temperature and
flow handles. Unscrew the flow
valve.
Remove the
cap, screw and
temperature
handle.
Turn cartridge
spindle
clockwise to
decrease the
temperature.
Turn cartridge
spindle
anti-clockwise
to increase the
temperature.
Reverse steps 1-2 to
reinstall the cartridge and
handle.
Replace nut and adaptor,
ensure the raised side is facing
towards the back of the valve.
Turn cartridge spindle clockwise to
decrease the temperature. Turn
cartridge spindle anti-clockwise to
increase the temperature.
Slide handle onto
adaptor and turn
clockwise until you
meet resistance. 12
Reverse steps 1-2 to
reinstall the valve and
secure handles.
REMEMBER
To service
your
product!
Slide soap
dish, hose
retainer &
handset
holder onto
the riser rail.
REMEMBER
To isolate your
product!
Insert wall plugs.
Secure the top bracket using
screws and push cap onto
bracket.
Slide the top
of the riser
through the
bottom of the
bracket.
Insert wall plugs & slide bottom
bracket onto rail
so the holes align.
Fix rail with screws and push
cap onto bracket.
Slide hose
through
hose retainer
before
attaching the
handset to
the shower.
