Bristan Regency Luxury R BSM C Wiring diagram

Regency Luxury Bath Shower Mixer
Installation Instructions & User Guide
IMPORTANT: Please keep these instructions for future reference and request of replacementparts

Safety
Note
1. Introduction
Thank you for choosing Bristan, the UK’s leading taps and showers expert. We
have designed this product with your enjoyment in mind. To ensure that it
works to it’s full potential, it needs to be fitted correctly.
These fitting instructions have been created to give you all of the information
you need and, if you need any further help, please do not hesitate to contact us
on 0330 026 6273.
2. Safety Note
Please red these instructions thoroughly and retain for future use.
All products manufactured and supplied by Bristan are safe provided they are
installed correctly, used correctly and receive regular maintenance in
accordance with these instructions.
These fittings need to be installed in accordance with and meet the
requirements of the Water Supply (Water Fittings) Regulations 1999 and
Scottish Bylaws 2004.
Before starting any installation please
consider the following:
•Prior to drilling into walls, check that
there are no hidden electrical wires,
cables or water supply. This can be
checked with the aid of an electronic
detector.
If power tools are used, do not forget
to:
•Wear eye protection
•Unplug equipment after use

3. Specification
Operating Pressure Range (bar)
Bath Shower Mixer Min. Max.
0.2 5.0
Maximum Static Pressure –10 bar
NOTE: Nominally equal (balanced) inlet supply pressures are recommended for optimum
performance
Designed to comply with BS EN 200 for single taps/combination taps for water systems
of type 1 and 2 general technical specifications and to be used within systems designed
to BS 6700.
BS6700 recommends the temperature of stored water should never exceed 65°C. A
stored temperature of 60°C is considered sufficient to meet all normal requirements and
will minimise the build up of lime scale in hard water areas
4. Installation
This mixer is suitable for use at all supply pressures. However, for optimum
performance, use both hot and cold water supplies, which should be ideally balanced.
Operating Pressures: Min. 0.2 Bar –Max. 5.0 Bar
If the fitting is installed at low pressure (tank fed), then the minimum distance from the
underside of the nozzle to the cold water tank should be at least 2 metres to ensure
adequate shower performance.
This mixer should be installed in compliance with Water Regulations.
Where the supplies are balanced, i.e. hot water from the cylinder tank and cold from the
mains, approved check valves must be fitted in the supply pipes.
For further details, please contact your Local Water Authority.

1
2
3
4
7
6
5
8
9
7
10
4. Installation Continued
1. Identify all components are present prior to installation
2. Fit the legs (1 and 2) to the body (3) using the large sealing washers (4)
3. Fit the mixer to the bath using the back nuts (5) and washers (6). Connect the hot
and cold water supplies.
4. Fit the wall bracket (7) to the wall using the fixing kit provided
5. Fit the hose (8) to the wall bracket and the handset
6. Fully open both valves, letting the water run for a few minutes to flush the system
and check for any leaks.
7. Operate the mixer in both bath fill and shower mode. To switch from bath filler to
shower mode, simply move the diverter lever (10) from one direction to the other

2
1
4
5
6
7
8
9
10
3
11
12
13
14
15
18
17
16
19
20
4. Installation Continued
Contents List
1. Indices x2 11. Anti-Splash x1
2. Screw x2 12. Nut x2
3. Handle x2 13. Pillar leg (left) and washer x1
4. Shroud x2 14. Back nut x2
5. Valve x2 15. Pillar leg (right) and washer x1
6. Hose and washer x1 16. Filter Washer x1
7. Diverter Lever x1 17. Shuttle x1
8. Diverter Mechanism x1 18. Outlet reducer x1
9. O Ring x1 19. Wall Bracket x1
10. Spout x1 20. Handset x1

5. Cleaning & Maintenance
Your fitting has a high quality finish and should be treated with care to preserve the
visible surfaces. All finishes will wear if not cleaned correctly. The safe way to clean
your product is to wipe with a soft damp cloth. Stains can be removed using washing up
liquid. All bathroom cleaning products (powders and liquids) will damage the surface of
your fitting, even the non-scratch cleaners.
NOTE: Never use abrasive detergents or disinfectants or those containing alcohol,
hydrochloric or phosphoric acid.
We advise that your fitting is regularly serviced, particularly in hard water areas.
Maintenance
Traditional valve type –if the fitting leaks from the spindle
1. Remove the fitting head
2. Tighten the gland nut on top of the valve
Sureflow type valves –if the fitting self opens
1. Remove the fitting head
2. Tighten the gland nut on top of the valve
All valve types –if the fitting begins to drip
1. Turn off both water supplies
2. Remove fitting head and valve
3. Carefully clean seating and rubber washer
4. Replace the valve and head. Turn on both water supplies
5. Contact our helpline if the problem persists

This booklet covers product codes
RBSM CR BSM G
R DBSM C R DBSM G
RLBSM CR LBSM G
R TBSM C R TBSM G
At Bristan, we want to make things as easy as possible for our customers.
That’s why we offer solid guarantees on all our products, effective from the
date of purchase, to give you peace of mind.
To start your free guarantee, simply scan the QR code and register your product.
Alternatively, visit www.bristan.com/register to register your product
via a computer.
For full guarantee terms and conditions visit, www.bristan.com/guarantees
Helpline
0330 026 6273
Bristan Group Limited
Birch Coppice Business Park, Dordon, Tamworth, Staffordshire B78 1SG
A Masco Company
Website:www.bristan.com
Telephone: [phone]
Email:[email protected]
REV. D7