Bristan K 1/2 C Wiring diagram

Installation Instructions
& User Guide
Please leave these instructions
with the end user
Pack Contents
Dynamic Water Pressure
Maximum Static Pressure: 10.0 bar
Min: 0.2 bar Max: 5.0 bar
Inlet Water Temperature
Operation
Tools Required for Installation/ Maintenance
To replace any spare parts
for your tap, why not
scan the QR Code or
visit www.bristan.com
and search for your
product.
Specifications
All products manufactured and supplied by Bristan are safe to use provided that they are installed, operated and
receive regular maintenance in accordance with these instructions.
This product needs to be installed in accordance with, and meet the requirements of The Water Supply (Water
Fittings) Regulations (Northern Ireland) 2009 and The Water Supply (Water Fittings) (Scotland) Byelaws 2014.
For full Installation Requirements & Notes (IRN) please visit www.wrasapprovals.co.uk/approvals-directory
Isolation valves must be fitted to the inlet water supplies to ensure ease of future maintenance.
Before installing this product the water supply must be thoroughly flushed in order to remove any swarf, solder etc.
Full access must be made available for future maintenance/servicing purposes.
This product must not be modified in any way as this will invalidate the guarantee.
Prior to Installation Spare Parts
0
1.0
2.0
5.0
4.0
3.0
Pressure
BAR
Open
Outlet
60°C
Inlet Connections
1/2” BSP
ON
ON
HOT
COLD
Maximum Hot 60°C
24mm
Box Spanner
17mm Socket
Spanner
Adjustable
Spanner
Pipe
Cutters
2mm Hex
Key
K 1/2 C (D6)
Crosshead
Screwdriver
Outlet Connections
x2 Tap Bodies
x2
Rubber
Washers
x2
Metal Backnuts

Connect the hot and cold water
supplies to the threaded tails.
3
REMEMBER
To fit
isolation valves
for maintenance
purposes
1*
4
1
Installation
Secure the taps to the basin/bath by
using the washer and metal backnut
below the basin/bath.
Hot
Cold
IMPORTANT
Turn on water
supply for a few
minutes and check
all joints and
connections for
any leaks.
IMPORTANT
Images shown are for illustrative
purposes only.
The tap you have purchased may look
dierent to those pictured in these
instructions, but will follow the same
installation steps.
Your contents page will be specific to
your product.
If you find your product or any of it’s
components dier from those shown on
the contents page, please contact our
Customer Support on - 0330 026 6273
Feed the tap body
through the
bath/basin and
ensure plinth and
plinth seals are in
place.
Your taps may
come with plinths
and will either be
included
pre-attached or
loose in the box
2REMEMBER
Hot on the
left, cold on
the right!
You may be required to
secure the plinth to the
tap with a grub screw.
If the hole is not
directly visible on the
plinth, check underneath
rubber seal
Ensure rubber seal is in
place once plinth is
attached

Maintenance - Valve Replacement
PLEASE NOTE - Taps shown in these instructions are for illustration purposes only.
All taps can be maintained using these instructions.
1
NOTE:
Grub screw
and cap can
also be located
at front of
handle
depending on
your tap.
Unscrew handle washer to
remove the handles.
Remove the handles depending on the style of your
tap, including any spline adaptors if used.
IMPORTANT
Isolate the
water supply
before
starting!
2Remove the valve using the tool
required for your tap. Check any
seals and O-rings for damage.
Replace valve if necessary.
Take care when
removing/replacing
your long stemmed
valve, as the finish
could be damaged
or scratched.
3
Reverse the steps to replace the
valves and handles.
123
4
Visit www.bristan.com or scan the
QR Code and search for your product code
to replace the cartridge for your tap.

3
Recessed Outlet
1a
Maintenance - Clean/Replace Outlet
Your tap may have
a dierent outlet,
use the
corresponding tool
and method to
remove
Check all loose
parts for any
damage, then soak
using a suitable
solution to de-scale
If provided, insert
the key tool into
the outlet and twist
to release it.
Using an
adjustable
spanner, unscrew
gently to remove
the outlet
Housed Outlet
2
Coin Slot Outlet
1c
1b
PLEASE NOTE - Taps shown in these instructions are for illustration purposes only.
All Taps can be maintained using these instructions.
IMPORTANT
Isolate the
water supply
before
starting!
12
Reverse the steps to
replace the outlet
1d
Using long-
nosed pliers,
unscrew
gently to
remove the
outlet.
Fixed Outlet
Using a coin,
insert into the
slot on the
outlet. Twist
to release it.

Troubleshooting
Symptom Cause Remedy
No flow or
low flow
rate
Partially closed isolation valve. Open isolation valve.
Head of water is below the
minimum distance required.
Refer to specification for minimum
distance required.
Hot or cold water being drawn o
elsewhere causing pressure changes or instan-
taneous boiler temperature
changes.
Do not use other water outlets
when using the taps.
Airlock or partial blockage in
the supply pipework.
Flush through pipework to ensure
removal of debris and any airlocks.
Water
dripping
from taps
This is normal for a short time after
using the taps.
This is caused by residual water tension,
the build up of water in the tap body.
If water continues to drip,
possibly due to the ceramic disc valves.
Remove valves and clean, refer to
'Maintenance' section before starting
any maintenance.
Taps do not
turn on
Closed isolation valve. Open isolation valve.
Mains water supply turned o. Turn on mains water supply.
Our Guarantee
Bristan Group Ltd.
UK: Bristan Group, B78 1SG.
EU: Masco Europe S.à.r.l.
14 Rue Strachen
6933 Mensdorf
Luxembourg
Customer Service: [phone]
Web: www.bristan.com
Email: [e-mail]
A Masco Company
Contact Us
At Bristan, we want to make things as easy as possible for our customers. That’s why we oer
solid guarantees on all our products, eective from the date of purchase, to give you peace of mind.
To start your free guarantee simply scan the QR code and register your product.
Alternatively visit www.bristan.com/register.
For any other queries, please call our Customer Service on 0330 026 6273 where our expert team
of advisors will be able to oer you any help and advice.
For full guarantee terms and conditions visit www.bristan.com/service-centre/guarantees
Bristan products are made from
premium materials, with hand polished,
electroplated, PVD or EPD finishes.
Your taps should be regularly cleaned
with warm water, a mild pH-neutral
liquid soap and polished with a
soft cloth. Any residues from soap,
toothpaste etc. can cause blemishes
if not rinsed o straight after use.
Household bleaches and cleaners
contain harsh chemicals and may damage
the surface finish. Avoid using abrasive
cloths, scouring pads, scrub sponges,
steel wool or anything similar.
General Cleaning