Brita Hydration Station 2500.CT User manual

02/15 Model 2500.CT Page 1 of 11
No. 2077014 (6)
1455 Kleppe Lane Sparks, NV 89431-6467 [phone]
website: www.BritaHydrationStation.com
QUICK START REFERENCE (SEE INSTALLATION INSTRUCTIONS FOR FURTHER DETAILS)
© 2015 Haws®Corporation – All Rights Reserved
HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation.
The BRITA trademark and logo are registered trademarks of Brita LP and used under license by Haws Corporation. All rights
reserved.
Model 2500.CT
Counter-to
p
Brita®H
y
dration Station®
OWNER’S MANUAL
Brita® Hydration Station®
Limited Warranty
For complete warranty information, please see page 10 of this owner’s manual.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE USE OF THIS MODEL, OR
REQUIRE REPLACEMENT PARTS, PLEASE CALL:
TECHNICAL SUPPORT:
1-800-766-5612
HOURS OF OPERATION: MON-THURS 7:00a.m. - 4:00
p
.m. PT
,
FRI 7:00a.m. - 1:00
p
.m. PT
RATED SERVICE FLOW: 0.55 GPM (2998L/day) OPERATING TEMP: 35-100°F (1.7-37.8°C)
FILTER CAPACITY: 1500 gallons (5678L) or 12 months
REPLACEMENT CARTRIDGE: Brita®Filter Model 6441
WATER SUPPLY REQUIREMENTS: 88 PSI (5.99 ATM) max supply pressure; cold water only.
Do not use with water that is microbiologically unsafe or of unknown quality without adequate
disinfection before or after the system. Systems certified for cyst reduction may be used on
disinfected waters that may contain filterable cysts.
NOTE: When installing this unit, all pertinent local, state, or federal codes should be adhered to.
This unit is certified for indoor use onl
y
.

02/15 Model 2500.CT Page 2 of 11
BRITA Trademark Usage Guidelines
The Brita trademark and Brita logo (collectively, the “Brita Marks”) are among the most critical elements of
Brita LP’s identity and convey many aspects of our business. The Brita Marks are widely recognized,
positive industry symbols and can be a very effective way to highlight your commitment to the
environment and providing high quality drinking water to your patrons.
The following guidelines apply to customers of the Brita®Hydration Station®water dispensing units and
Brita®filters.
Your purchase of this Brita®product authorizes your company to use and/or display the Brita Marks as
long as:
You continue to use Brita®filters in the Brita®Hydration Station®water dispensing unit and
replace the Brita® filters as instructed
You maintain your Brita®product at an appropriate level to provide high quality drinking water to
your patrons
You do not disparage Brita, LP or Brita®products
You do not imply a relationship or association with Brita, LP that does not exist
You adhere to these Trademark Usage Guidelines
Improper use of the Brita Marks may be considered a violation of these Trademark Usage Guidelines,
and Brita, LP reserves all rights to enforce proper use of its trademarks, including but not limited to having
you remove or cover up the Brita Mark on the product.
In the event you have questions about the proper use of the Brita Marks, the Brita®filters or the Brita®
Hydration Station®water dispensing unit, please call 888-909-4297 to be connected to a representative of
Haws Corporation. The Brita Marks are registered trademarks of Brita LP and are used under license by
Haws Corporation.
Haws Corporation
1455 Kleppe Lane • Sparks, NV 89431
1-888-909-4297
www.Britahydrationstation.com

02/15 Model 2500.CT Page 3 of 11
Installation
NOTES:
1. Keep the unit upright while moving, operating, or storing it.
2. This unit is certified for indoor use only. Be certain that the installation location for this
unit is level, is not in direct sunlight, is not next to a heat source, and will not freeze. 4” of
clearance around the unit must be maintained to facilitate air circulation.
3. Install this unit within 6’ of its power source. Do not use extension cords or two-pronged
power outlets.
4. Do not use with water that is microbiologically unsafe or unknown quality without
adequate disinfection before or after the system. Systems certified for cyst reduction may
be used on disinfected waters that may contain filterable cysts.
5. For all plastic 1/4" push-in type fitting connections, only connect NSF-61 copper or plastic
tubing. Stainless steel or glass tubing is not recommended. The following assembly
instructions must be followed to ensure a watertight connection:
a. Cut tubing square and clean.
b. Mark 11/16” from end of tube.
c. Push tube into the fitting until it bottoms out.
d. To remove, depress collet and pull tubing out.
Cooler Installation
STEP 1: Remove the bright orange Trademark Usage Guidelines Agreement label on the filter (see
below), thereby accepting the guidelines. The label reads as follows:
Removal of this label signifies you or an appropriate owner’s agent will comply with all
BRITA® Trademark Usage Guidelines as well as maintain the unit to the standards as
first installed. Detailed information noting requirements can be found in the Owner’s
Manual.
Screw the filter cartridge into the filter head.
PARTS LIST: 1 Brita®Hydration Station®, 1 drip tray, 1 filter cartridge, 1 filter head, 1 pressure
regulator with plastic tubing.
OPTIONAL ACCESSORIES: 0006532549 1/4" leak-detecting valve.
RECOMMENDED TOOLS: Phillips screwdriver, tubing cutter, adjustable wrench.
REQUIRED PARTS (NOT SUPPLIED): Water supply shutoff valve, 1/4” tubing (for water supply)
SUPPLY LINE: 1/4" tubing. Cold water supply only. Intended for municipal water only.
ELECTRICAL CONNECTIONS: 115VAC, 60HZ, approx. 4.7A. Unit is equipped with a standard
115VAC plug. NOTE: A Class A ground-fault circuit interrupter (GFCI) shall be installed in the
branch-circuit supplying power to this unit.
S
IZE:
App
r
o
xim
ate
l
y
17-
5/
1
6
”H x 14-1
/
4”W x 1
9
-
3/
4”D.

02/15 Model 2500.CT Page 4 of 11
STEP 2: Remove the top lid of
the cooler. Unscrew
the 3 Phillips screws
that hold down the
internal lid and lift it
out of place. This will
expose the filter area.
STEP 3: Locate the tubing
running into the float
valve on the cooler
tank (see diagram).
There are several
inches of extra length
on this tubing down
in the filter area;
without disconnecting
either end, pull this
extra length out and
cut it squarely approximately at the midpoint.
STEP 4: Lower the filter assembly partway into the filter area. Connect the newly-cut length of tubing
running from the float valve into the filter outlet (ports are labeled). Connect the other cut
length of tubing into the filter inlet. Lower the filter assembly completely into the cooler, taking
care not to kink the tubing.

02/15 Model 2500.CT Page 5 of 11
STEP 5: Install the tubing attached to the pressure regulator outlet into the inlet on the back of the
cooler. Tubing may be shortened if so desired. NOTE: The regulator protects against
sudden pressure increases in the supply line.
STEP 6: Provide a water supply inlet of 1/4" tubing with a code-compliant shutoff valve (valve and
tubing not supplied). If the optional 0006532549 1/4" leak-detecting valve was purchased,
install it in the inlet plumbing as well. This valve is designed to shut off the water supply if
water contacts it, so it is best to secure it firmly to whatever surface the cooler is resting upon,
very close to the cooler itself; supplied tubing may be shortened if so desired (NOTE: Take
care not to introduce water to this valve by mopping, etc.). Connect the assembled water
supply plumbing to the inlet of the pressure regulator.
STEP 7: Elevate the front of the cooler slightly and
slide the drip tray into place beneath the
nozzle. The cooler should sit flat if the
drip tray is properly aligned.
STEP 8: Any new filter cartridge must be purged of
bubbles and carbon particles (both of
which are normal in a new filter) before it
can be used. Do not purge the filter
through the cooler; do this instead:
Disconnect the tubing at the filter outlet
and install a separate length of tubing (by
others) into the outlet (see note 5 on page
3). Direct this tubing into a suitable
container or drain, and turn on the water
supply to purge 5 gallons water through
the filter and into the container. Turn off
the water and re-install the original filter
plumbing when done.
This step is necessary for replacement filters as well.

02/15 Model 2500.CT Page 6 of 11
STEP 9: Remove the top cover from the unit, and then carefully pry the circular lid off of the water tank.
On the underside of the lid are two floats – the larger float is the main float that closes the
water inlet valve when the tank is filled. The smaller float is the failsafe float; it keeps the tank
from flooding if the main float malfunctions.
NOTE: If the failsafe float trips, water cannot flow through the inlet valve until the red
reset button on the top of the inlet valve is pressed.
Make sure the floats have not become dislodged and can move freely. Press the failsafe float
upward against the tank lid to trip it, but do not reset it at this point.
STEP 10: Turn on the inlet water supply – the system should not fill, because the failsafe float
mechanism was tripped in Step 9. Press the red reset button on the inlet valve on the water
tank lid; the system should fill. NOTE: This verifies that the failsafe float is functioning.
Check the inlet tubing and the unit for leaks. Reinstall the inner lid and replace the top lid.
STEP 11: Make sure that the hot
water tank power switch on
the back of the cooler is in
the “Off” position. Plug the
cooler into 115VAC wall
power using the supplied
power cord.
STEP 12: Press the “Cold” button (see
diagram under Operation
section); the ring around the
“Water” button should turn
blue. Press and hold the
“Water” button until water
begins to dispense (if it does not emit from the nozzle after a moment, consult the
Troubleshooting section).
STEP 13: Press the “Hot” button (see diagram under Operation section); the ring around the “Water”
button should turn red. Press and hold the “Water” button. The hot tank will fill and water will
eventually begin to dispense. Stop and restart dispensing until all air is evidently gone from
the system. Flip the hot tank power switch to “On.”
NOTE: Turning on the hot tank power switch without first filling the tank can damage
the unit.
SIP Sanitization Setup
The cooler may be sanitized using the integral SIP (Sanitize in Place) ozone technology. This
can be done by using the default daily sanitization mode (see below) or by running the SIP
manually for a more complete cleaning (see Maintenance section).
NOTE: The system is not available for use while the SIP sanitization is running
(approximately 1 hour), so it is generally preferable to set it to run when the cooler is
least likely to be needed.
STEP 14: Press and hold the white button on the back of the cooler (see diagram above) until it has
beeped twice (about 7 seconds). The light ring around the “Water” button will begin flashing
white.
STEP 15: The SIP system is designed to activate automatically every 24 hours. Press the white button
X number of times, where X equals the number of hours from the current time until the
desired daily sanitization time, then press the “Water” button to save the new setting.
Example: you are setting up the SIP sanitization and it is 2PM. You want the SIP to activate
every day at 10PM, so you press the white button 8 times, and then press the “Water” button.
NOTE: Pressing a button other than the “Water” button or the white SIP button, or waiting 15
seconds without pressing any button, will exit from setup mode without saving.
NOTE: Entering setup mode (as done in Step 14) and immediately pressing the “Water”
button will turn the SIP functionality off.
STEP 16: Sanitize the exterior of the unit with Clorox®Anywhere® Hard SurfaceTM Daily Sanitizing Spray
before using.
See the Maintenance section for further instructions on the SIP user interface.

02/15 Model 2500.CT Page 7 of 11
Operation
Dispensing Cold Water
To dispense cold water, press the
“Cold” button; the ring around the
“Water” button should turn blue.
Press and hold the “Water” button to
dispense; release the button to stop
dispensing.
Dispensing Hot Water
To dispense hot water, press the “Hot” button; the ring around the “Water” button should turn
red. Press and hold the “Water” button to dispense; release the button to stop dispensing.
CAUTION: Water dispensing from the hot tank is sufficiently hot to cause injury. Take care
when dispensing hot water.
Maintenance
Filter Changes
NOTE: Filter life is 1500 gallons
or 12 months, whichever comes
first. With higher usage, filter
life may need to be replaced
sooner. See your water dealer
for more information.
STEP 1: Remove the top lid of the cooler.
Unscrew the 3 Phillips screws
that hold down the internal lid
and lift it out of place. This will
expose the filter area.
STEP 2: Pull the filter out enough to unscrew the cartridge from the head. When the cartridge is free,
move the head aside, pull the cartridge out and lower a new one in its place, screwing it firmly
into the head. Lower the filter back into its place.
STEP 3: The new filter cartridge must be purged before it is used. Shut off the inlet water supply and
see STEP 8 under the Installation section for instructions on how to safely do this.
STEP 4: Turn on the inlet water supply. Dispense water; check for leaks. Replace the covers removed
in STEP 1.
STEP 5: Note the date of filter change on the filter replacement sticker on the back of the unit.
Annual Float Check

02/15 Model 2500.CT Page 8 of 11
Once a year, carefully pry the lid off of the water tank and press the smaller float (i.e. the failsafe
float) against the lid to trip it. This should stop water flow through the inlet valve. Inspect both
floats to assure that they are not dislodged or damaged. Replace the lid and press the red reset
button on the inlet valve to allow water flow through the valve again.
Drip Tray
Remove the tray by lifting the front of the cooler and pulling it out. Reverse to re-install.
Nozzle Light Brightness Control
Press the “Light” button (see button diagram on page 6) to toggle 100% or 50% brightness.
Cleaning
It is recommended that the exterior of the unit and the drip tray be cleaned regularly using a
mild sanitizing cleaner, such as Clorox®Anywhere® Hard SurfaceTM Daily Sanitizing Spray.
SIP Sanitizer Maintenance
Checking the Sanitization Schedule
Press the white button on the back of the unit (see diagram on page 6). It will beep the
number of hours until the SIP is scheduled to start.
Example: It is 3PM and the unit beeps 9 times. The SIP is set to run daily at midnight.
Changing the Sanitization Schedule
See “SIP Sanitization Setup” on page 6 for how to set the daily SIP activation time.
Running SIP Manually for Full Cold Water System Cleaning
NOTE: The cooler cannot be used while the SIP sanitization is running (about 1 hour).
STEP 1: Manual SIP mode cleans the entire cold water system, not just the tank, so water is dispensed
during the cleaning cycle. Place a 1-liter container (or larger) under the nozzle.
STEP 2: Press and hold the white SIP button (see page 7 diagram) until it beeps once (about 3
seconds) to begin the manual SIP cycle. Water will occasionally dispense. At the end of the
cycle, the entire cold water system will be sanitized.
Troubleshooting
BRITA®HYDRATIONSTATION®TROUBLESHOOTING
PROBLEM REPAIR CHECKLIST
1. Water is not dispensing. a.
b.
c.
d.
e.
Verify power and water to the unit.
Check that the float assembly is not tripped
– remove top lid from unit and press the red
reset button on the valve in the lid of the
tank – some water may come out.
Is the SIP feature activated?
Replace filter.
Can the pump be heard coming on when
water is called for?
2. Warm water is dispensing from the cold
side.
a.
b.
c.
Is usage exceeding the cooling capacity?
Is the unit in direct sunlight or near heat?
Check cold thermostat setting (see diagram
on page 6 for thermostat location) – 1/4 turn
clockwise for colder water.
3. Water out of the hot tank is not hot. a.
b.
Is hot tank switch turned on (see diagram
on page 6 for switch location on back of
unit)?
Is usage exceeding the heating capacity?
4. Hot water is boiling. a. Possible air in hot tank – dispense hot water
to remove air from tank.
Please call technical support at 1-800-766-5612 if you are unable to troubleshoot this unit.

02/15 Model 2500.CT Page 9 of 11
PERFORMANCE DATA SHEET
IMPORTANT NOTICE: Read this Performance Data Sheet and compare the capabilities of this unit with
your actual water treatment needs. It is recommended that, before purchasing a water treatment unit,
you have your water supply tested to determine your actual water treatment needs.
Substance Influent Challenge
Concentration
Reduction
Requirement
Maximum Permissible
Product Water
Concentration
Average Percent
Reduction
Chlorine,
Taste
and Odor
2.0 mg/L ± 10% ≥50% N/A 96.6%
Lead 0.15 mg/L ± 10% N/A 0.010 mg/L 99%
Cyst Minimum 50,000/L 99.95% N/A 99.99%
This system has been tested according to NSF/ANSI 42/53 for the reduction of the substances listed.
The concentration of the indicated substances in water entering the system was reduced to a
concentration less than or equal to the permissible limit for water leaving the system, as specified in
NSF/ANSI 42/53.
Testing was performed under standard laboratory conditions. The contaminants or other substances
removed or reduced by this water treatment device are not necessarily in all users’ water. Filter
performance may vary based on local water conditions.

02/15 Model 2500.CT Page 10 of 11
BRITAHYDRATIONSTATION
LIMITEDWARRANTY

TERMSANDCONDITIONS.ThiswarrantyisprovidedbyHawsCorporation(Hereinreferredtoas“HAWS”).Thiswarranty
providesfor,atHAWS’ssolediscretion,theentirereplacementofaPointofUseWaterCooler(Hereinreferredtoas“POU
Cooler”)deemeddefectiveorreplacementofjustthedefectivepartsofthePOUCoolerinquestion.ThisLimitedWarranty
doesnotprovideforanylaborallowancestoDealertorepairdefectivePOUCoolers.ThisLimitedWarrantydoesnotoffer
coverageforcomponentsthatarenotfactoryinstalledsuchasdealer‐installedaccessoriesnotoriginallysoldbymanufacturer.
CustomeragreestonotifyHAWSinwritingifanynonconformity,defect,damage,contamination,orproblemwiththePOU
Cooler.
INSTALLATIONANDOPERATION.ThisLimitedWarrantyappliesonlywhenthePOUCoolerisinstalledandoperatedin
accordancewithHAWS’swritteninstructionsincludedwitheachunit.ItdoesnotapplytoPOUCoolers,whichonexamination
byHAWShavebeensubjectedtoaccident,modifications,reconditioning,abuse,misuse,misapplications,corrosivetype
atmospheres,abnormaluseordamagefromshippingandhandling.
WarrantyCoverage:
FIRSTTWOYEARS:HAWSwarrantsthecompletePOUCoolerincludingcompressor,hermeticallysealed
refrigerationsystem,faucetorfaucets,andelectricalcomponents(coldcontrol,compressor,overload/relay,heatband,and
hotcontrols)tobefreefromdefectsinmaterialandworkmanshipundernormalusefor2years(24months)fromtheInvoice
date.HOWEVER,theFloatAssemblywithtubingiswarrantedfor1year(12months).Noincreaseoralteration,writtenor
verbal,ofthiswarrantyisauthorized.
THIRDYEAR:HAWSwarrantsthefollowingsystemandcomponentstobefreefromdefect.Coverageislimitedto
replacementofdefectivecomponentorreplacementofcompletePOUCooleratHAWS’soption,inanycase,thevalueofthe
WarrantyshallnotexceedthepurchasepricepaidforthePOUCooler.
REFRIGERATIONSYSTEMIncludesreplacementofthefollowinglistedparts:compressor,evaporator,
condenser,connectingrefrigerantlinesanddrier.
MinorRepairs.UponnotificationofadefectivepartandPOUCoolerserialnumberbydealer,HAWSwillreplacethepartsfree
ofchargeeitherprovidingtheactualpartsasreplacement,orissuingcreditforthepurchasepriceoftheparttothedealer
within30days.Dealeracknowledgesthatitmusthaveonlyqualifiedtechnicians,asdefinedbystateandlocalcodes,perform
anypartsreplacementorelsethewarrantysetforthhereinwillbevoided.Anylaborchargesandshippingcostsassociatedwith
minorrepairswillbetheresponsibilityofthedealer.
MajorRepairs/Refrigeration(SealedSystemRepairs).Uponnotification(toincludetheserialnumberandreasoncodefor
themajorfailure)ofamajordefectintherefrigerationsystem,HAWSwillprovidedealerareplacementPOUCoolerwithaone
(1)yearlimitedwarranty,onthesametermsandconditionsascontainedherein,atnochargeoncustomer’snextorder.Dealer
mustholdPOUCoolerswithmajordefectsfor30daysintheeventHAWSpersonnelneedtoinspectthecoolers.Dealermay
thereafterdisposeofthePOUCoolersatdealer’sexpense.
CUSTOMER’SOBLIGATIONS.Customermustprovideproofofinstallationdatewhenrepairisrequired.TheCustomeralsohas
theobligationandresponsibilitytoreturnthecompleteunittotheowner’sequipmentorservicecenterorclosestauthorized
distributor(HAWSatwww.BritaHydrationStation.com;or800‐766‐5612),ifthecompressor,refrigerationorwatersystemis
foundtobedefectiveduringthewarrantyperiod,atCustomer’ssoleexpense.
HAWS’SOBLIGATIONS.HAWS’sobligationunderthisLimitedWarrantyislimitedtosupplyingthepartsorissuingcreditfor
minorpartsortothereplacementoftheentirePOUCoolerorissuingcreditforthePOUCoolerdispenseroranypartofthe
POUCoolerwhichisexpresslycoveredbythisLimitedWarrantyasstatedabove,butonlyifHAWSdeterminesthatthePOU
Cooler,thepartorparts,andthepurporteddefectordefects,arecoveredbythisLimitedWarranty,inHAWS’ssolediscretion.
ThisLimitedWarrantycoversthePOUCooleronly.


02/15 Model 2500.CT Page 11 of 11
PERSONSENTITLEDTOBENEFITWARRANTY.ThisLimitedWarrantyisapplicableonlyto(i)originalpurchaserswhopurchase
thePOUCoolerforresaleorrentalintheordinarycourseofbusiness(i.e.dealer),and(ii)thefirstconsumerwhopurchasesthe
POUCoolerotherthanforresaleorrental(referredtocollectivelyhereinas“Customer”.)Dealeragreestocommunicateto
consumeranyandallwaiversandlimitationscontainedinthisLimitedWarranty.WARNING:ThisproductislistedwithUL.UL
Certificationisvoidifthecoolerismodified,combinedwithotherdevices,orarefurbishingprocessisusedthatcandamage
theelectricalcomponentsandmaycauseelectricalshockorfire.AnyquestionsregardingthisLimitedWarrantyorperformance
ofHAWS’sobligationsunderthisLimitedWarrantyshouldbeaddressedtoHAWSatwww.BritaHydrationStation.com;800‐
766‐5612.
PreservationandPlacementofPointofUseCooler.CustomershalluseanyandallmeansnecessarytoensurethatthePOU
Coolerispreserved,safeguarded,andkeptinitsoriginalcondition.CustomerunderstandsthatPOUCoolerisawaterappliance
andmayexperiencecondensationorothermoisturefromtimetotime,andassuch,shallberesponsibleforproperplacement
ofthePOUCooler.CustomershallberesponsibletocontacttheirauthorizedDealerforinspectingPOUCoolersannuallyand
understandsthatseriouswaterdamagecanoccuriftheunitisnotmaintainedorinstalledproperly.
DisclaimerofExpressandImpliedWarrantiesandConsequentialDamages.InnoeventshallHawsCorporationbeliablefor
thepaymentifanyconsequential,punitive,indirect,orspecialdamages,includingbutnotlimitedtolostprofits,irrespectiveof
whethersuchdamagespurportedlyarisefromcontractortort.HAWS’sliability,ifany,shallbelimitedtoeitherproviding
replacementpartsorreplacementofthePOUCooler.Undernocircumstanceswillliabilityexceedtheamountspaidby
CustomerforitspurchaseofthePOUCooler.HAWSshallnotbeliableforanydamagescausedbyorwhichariseoutoftheacts
oromissionsofathirdparty.THEWARRANTIESANDREPRESENTATIONSSETFORTHHEREINAREINLIEUOFANYOTHER
WARRANTY,EXPRESS,IMPLIEDORSTATUTORY,INCLUDING,BUTNOTLIMITEDTO,ANYIMPLIEDWARRANTYOF
MERCHANTABILITY,QUALITYORFITNESSFORAPARTICULARPURPOSE.CUSTOMER’SSOLEANDEXCLUSIVEREMEDYIN
CONTRACT,TORTORUNDERANYOTHERTHEORYAGAINSTHAWSRESPECTINGTHEGOODSAREASDESCRIBEDHEREINANDNO
OTHERREMEDY(INCLUDING,WITHOUTLIMITATION,CONSEQUENTIALDAMAGES)SHALLBEAVAILABLETOCUSTOMER.Some
statesdonotallowlimitationsonhowlonganimpliedwarrantylasts,andtowhatextentconsequentialdamagesmaybe
limited,sothelimitationsmaynotapplytoyou.Thislimitedwarrantygivesyouspecificlegalrights,andyoumayalsohave
otherrights,whichvaryfromstatetostate.
Miscellaneous.Thisdocumentconstitutesthefinalandentireagreementamongpartieswithrespecttothesubjectmatter
hereof.UnlessmodifiedbyHAWSinwriting,thisLimitedWarrantysupersedesalloralorwrittencommunicationsrelatingto
thePOUCooler,includingstatementsmadebysalespersons.









© 2015 Haws®Corporation – All Rights Reserved
HAWS® and other trademarks used in these materials are the exclusive property of Haws Corporation.
The BRITA trademark and logo are registered trademarks of Brita LP and used under license by Haws Corporation. All rights
reserved.
SHOULD YOU EXPERIENCE DIFFICULTY WITH THE USE OF THIS MODEL, OR
REQUIRE REPLACEMENT PARTS, PLEASE CALL:
TECHNICAL SUPPORT:
1-800-766-5612
HOURS OF OPERATION: MON-THURS 7:00a.m. - 4:00
p
.m. PT
,
FRI 7:00a.m. - 1:00
p
.m. PT