Britax MARATHON CS User manual

MarathonTM CS
User Guide
PLEASE READ
INSTRUCTIONS
STORE UNDER
COVER
IMPORTANT:
� DOUBLE CHECK EVERY TIME YOU
USE THIS CAR SEAT.
Double Check Car Seat-to-Vehicle Installation:
� Check that the LATCH or vehicle seat belts connections to the
vehicle are tight and locked.
� Verify the car seat cannot be moved front-to-back or side-to-side
more than one inch (2.5 cm) at the connection point.
Double Check Child-to-Car Seat Installation:
� Tug on the buckle to ensure proper locking.
� Confirm harness straps are snug and over both shoulders and
hips. You should not be able to pinch excess harness strap
webbing at the child’s shoulder.
� Make sure the chest clip is properly fastened and positioned in
the middle of the child’s chest at armpit level.
Britax Child Safety, Inc.
13501 South Ridge Drive
Charlotte, NC 28273
USA
A Britax Childcare Group Limited
company
Tel [phone]
www.BritaxUSA.com

1
Safety Information
Warnings...............................................................................................................2
Important Notes....................................................................................................4
Certification...........................................................................................................5
Registration...........................................................................................................5
Important Harness Adjustments..........................................................................6
Child Seat Features.............................................................................................8
Vehicle Compatibility
Incompatible Vehicle Belts...................................................................................10
Vehicle Buckle Positions......................................................................................11
Vehicle Seating Positions.....................................................................................11
Installation: Rear-facing
LATCH Installation................................................................................................12
Lap-Shoulder Belt Installation .............................................................................14
Lap-Belt Installation .............................................................................................16
Installation: Forward-facing
LATCH Installation................................................................................................18
Lap-Shoulder Belt Installation..............................................................................20
Lap-Belt Installation .............................................................................................22
Installation: Aircraft.............................................................................................24
Installation: Versa-Tether®
Safety Information ................................................................................................25
Using the Versa-Tether®.......................................................................................26
Tether-Connector Strap........................................................................................27
Energy-Absorbing Versa-Tether®.........................................................................28
Child Seat Functions
Storing the LATCH Connectors...........................................................................29
Recline Adjustment ..............................................................................................29
Chest Clip .............................................................................................................30
HUGS™ Chest Pads ..............................................................................................30
Harness Buckle ....................................................................................................31
Adjusting Harness Slot Height ............................................................................31
Securing Your Child ............................................................................................32
Care and Maintenance........................................................................................34
Warranty ...............................................................................................................38
©2009 Britax Child Safety, Inc. All rights reserved. Printed in U.S.A P332400_R1:04.09
This product and its components are subject to change without notice.
Table of Contents

2
3
Use only in a rear-facing position when using it with an infant•
weighing less than 20 lbs (9.1 kg) OR is less than 1 year of age.
Use only with children who weigh between 5 and 65 lbs (2.3 and•
29.5 kg) and whose height is 49 inches (124.5 cm) or less. Rear-
facing for children who weigh between 5 and 35 lbs (2.3 and 15.9
kg) and forward-facing for children who weigh between 20 and 65
lbs (9.1 - 29.5 kg) and are at least 1 year of age.
Snugly adjust the belts provided with this child restraint around•
your child. A snug strap should not allow any slack. It lies in a
relatively straight line without sagging. It does not press into the
child’s flesh or push the child’s body into an unnatural position.
Secure the top anchorage strap provided with this child restraint.•
Secure this child restraint with the vehicle’s child restraint•
anchorage system if available or with a vehicle belt.
Follow all instructions on this child restraint and in the written•
instructions located under the child seat cover.
Register your child restraint with the manufacturer.•
To prevent injury due to deterioration or hidden damage,•
discontinue use of a child seat that is older than six years or has
been in a moderate or severe crash. See Serial Number and
Manufacture Date Label located on child seat (see page 9).
This child seat must not be used in the home, in boats, or other•
non-certified applications.
Based on crash statistics, the National Highway Traffic Safety•
Administration (NHTSA) recommends that parents select the
back seat as the safest location for a properly installed child seat.
Please study the Vehicle Compatibility (pages 10-11) section in
this booklet to ensure your child’s safety and consult your vehicle
owner’s manual.
Secure this child seat even when it is not occupied. In a crash, an•
unsecured child seat may injure vehicle occupants.
When using in a vehicle with air bags, refer to your vehicle owner’s•
manual for child seat installation instructions and precautions.
Never use adjuster strap to lift or carry this child seat. Doing so•
could cause damage to harness adjuster and webbing. Always
carry this child seat by its shell or tether straps.
The primary protection for occupants of a vehicle in a collision is•
the body of the vehicle itself. A child seat will not protect a child
when a vehicle is seriously impacted. However, correctly installed,
a child seat will substantially improve chances for survival in most
crashes. Make sure all users fully understand the correct ways to
use this child seat in a vehicle.
The use of non-Britax Child Safety, Inc. covers, inserts, toys,•
accessories, or tightening devices is not approved by Britax. Their
use could cause this child seat to fail Federal Safety Standards or
not perform as intended in a crash.
HUGS• TM chest pads must be installed for forward-facing use.
Removal of HUGS is optional only for rear-facing use.
WARNING!
DEATH or SERIOUS INJURY CAN OCCUR:

4
5
Safety Information Safety Information
Important Notes
Verify child seat is secure and harness is properly adjusted around•
child each time child seat is used.
Adjust harness to fit clothes the child is wearing. Remove bulky•
coats and/or jackets before putting child in child seat.
Cover child seat when vehicle is parked in direct sunlight. Parts of•
child seat could become hot enough to burn a child.
Store child seat in a safe place when it is not being used. Avoid•
placing heavy objects on top of it.
Do not leave children alone in a vehicle, even for a short time.•
Do not, except as described in this booklet, attempt to disassemble•
any part of the child seat or change the way its harness or vehicle’s
seat belts are used.
Do not leave loose objects, e.g. books, bags, etc., in the back of•
a vehicle. In the event of a sudden stop, loose objects will keep
moving, potentially causing serious injuries.
Do not leave folding vehicle seats unsecured or unlatched. In event•
of a sudden stop, a loose seat back could prevent child seat from
protecting the child as well as it should.
Do not allow children to play with this or any child seat.•
Do not use anything to raise child seat off vehicle seat except as•
described in these instructions. In a crash, child seat could slide
and may not adequately protect the child.
Certification
This child seat system conforms to all applicable Federal Motor Vehicle
Safety Standards. This child restraint is certified for use in motor vehicles
and aircraft.
Registration
Child seats can be recalled for safety reasons. You must register this
child seat to be reached in a recall. Send your name, address, and
the child seat’s model number and manufacturing date to Britax Child
Safety, Inc., 13501 South Ridge Drive Charlotte, NC 28273, or call
1-888-4BRITAX, or register online at www.BritaxUSA.com/registration.
For recall information, call the US Government’s Vehicle Safety
Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to http://
www.NHTSA.gov.
Serial Number:___________________________________
Batch Number:___________________________________
Date of Manufacture:______________________________
WARNING! DO NOT place a child seat
rear-facing in the front seat of a vehicle with
a passenger air bag. DEATH or SERIOUS
INJURY can occur. See your vehicle owner’s
manual for child seat installations. The back
seat is the safest place for children under 12.

6
7
Safety Information Safety Information
Important Harness Adjustments
According to the American Academy of Pediatrics:
All infants should ride rear-facing until they have reached at least 1
year of age and weigh at least 20 pounds (9.1 kg). That means that
if your infant reaches 20 pounds (9.1 kg) before her first birthday, she
should remain rear-facing at least until she turns 1 year old. It is best
for children to ride rear-facing to the highest weight or height allowed
by the manufacturer.
Rear-Facing
Use rear-facing only with children:
who weigh between 5 and 35 lbs (2.3 – 15.9 kg)• and
the top of the child’s head is at least 1” (2.5 cm) or•
more below the top of the child seat (Fig. A) and
the harness straps are in the nearest slots at or•
below the child’s shoulders.
If the child cannot be secured within these requirements because the
child exceeds height or weight requirements, review the forward-facing
guidelines on page 7.
If the child cannot be secured within these requirements because the
child is too small, selection of a different child seat (such as an infant
carrier) may be required.
IMPORTANT: See Adjusting Harness Slot Height on page 31.
WARNING!
Do NOT use the child seat rear-facing if any of the following apply:
the child is less than 5 lbs (2.3 kg) in weight• or
the child exceeds 35 lbs (15.9 kg) in weight• or
the top of the head is less than 1” (2.5 cm) from the top of the child•
seat (Fig. A) or
the harness straps are in a slot above the child’s shoulders.•
WARNING!
Do NOT use the child seat forward-facing if any of the following apply:
the child is less than one year of age• or
the child is less than 20 lbs (9.1 kg) in weight• or
the child exceeds 65 lbs (29.5 kg) in weight• or
the child exceeds 49” (124.5 cm) in height• or
the top of the ears are above the top of the child seat• or
the top harness slots fall below the child’s shoulders, parallel to level•
ground (Fig. B)
1 inch
2.5 cm
Rear-Facing
A
Forward-Facing
Use forward-facing only with children:
who are at least one year of age• and
who weigh between 20 and 65 lbs (9.1 – 29.5 kg)• and
49” (124.5 cm) or less in height• and
the top of the child’s ears are below the top of the child seat• and
the harness straps are in the nearest slots at or above the child’s•
shoulders, parallel to level ground (Fig. B).
IMPORTANT: When using forward-facing recline mode, it may
become necessary to adjust the harness to the next higher set of slots
than would be used when the seat is upright. See Adjusting Harness
Slot Height on page 31.
Shoulder level
Above Shoulder Level
Below Shoulder Level
UprightReclined
Forward-Facing Harness Height
B

8
9
Cover1
LATCH Straps2
LATCH Adjuster Release Buttons3
LATCH Adjusters4
LATCH Connector Release Buttons5
LATCH Connectors (stored under6
cover)
Harness Slots7
Comfort Pads8
Chest Clip9
Harness Holders10
HUGS11
™
(Harness Ultra Guard
System) Chest Pads
Harness12
Buckle13
Belly Pad14
Harness Adjuster15
Lever (under cover)
Click & Safe Snug Harness16
Indicator (under cover)
Harness Adjuster Strap17
Recline Handle18
20
22 25
23
27
26
28
21
19
24
7
8
9
10
11
12
14
13
15
1
17
16
18
2
3
4
5
6
Child Seat Features Child Seat Features
Serial Number & Manufactured19
Date (under cover)
Versa-Tether20 ®(Top Anchorage Strap)-
in pouch
Versa-Tether Storage Pouch21
Harness Yoke22
Belt Guard23
IMPORTANT: When not in use, this user
guide should be stored under the cover.
DO NOT discard the foam inserts found
under the cover.
Shell24
Forward-Facing Lock-off25
Rear-Facing Lock-off26
LATCH Bar27
Base28

10
11
Vehicle Compatibility Vehicle Compatibility
WARNING! The following types of vehicle belts are NOT
compatible with this child seat:
Vehicle belts with top or1
bottom anchor points on
the vehicle door.
Motorized, automaticvehicle
2
belts
Lap-shoulder belts that
3
have a separate retractor
each for the lap section
and shoulder section
Lap belts forward of the
4
vehicle seat bight.
Lap belts that have a retractor that locks only
5
in case of a sudden stop (emergency locking
retractor or ELR).
Incompatible Vehicle Belts Vehicle Buckle Positions
WARNING! The position of the vehicle
belt buckle can adversely affect the stability of
the child seat.
If the buckle lies near the incorrect position ( ) when
the vehicle belt is tightened, try fitting the child seat
in another seating position in the vehicle OR consult
your vehicle owner’s manual to see if you can lower
the vehicle buckle position by twisting the vehicle
buckle stalk. If it is not possible to achieve the correct
position ( ) for the buckle, then another seating
position MUST be used.
Vehicle Seating Positions
WARNING! Some vehicles have no seating positions which
are compatible with this child seat or any other child seat. If in doubt,
contact the vehicle manufacturer for assistance.
Forward-facing vehicle seats MUST be used with this child seat. Side-
facing or rear-facing seats CANNOT be used. See diagram below.
DO NOT place a child seat
rear-facing in the front seat
of a vehicle with a
passenger air bag unless
deactivated. DEATH or
SERIOUS INJURY can
occur. See your vehicle
owner's manual for child
seat installation instruc-
tions. The back seat is the
safest place for children
12 and under.
WARNING!

12
13
Installation: Rear-Facing Installation: Rear-Facing
with the “LATCH Strap Here Rear-Facing”
label on each side of the child seat. (Figs. E
and F).
Push the child seat firmly into the vehicle seat7
while pulling each LATCH strap tight (Fig. G).
IMPORTANT: Ensure the LATCH strap does not fold
into the LATCH adjuster while tightening.
Verify that all connections are secure, the8
LATCH strap is aligned to the “LATCH Strap
Here Rear-Facing” label on each side of the
child seat, and that the child seat is stable.
The child seat is secure when it cannot be moved•
more than 1 in. (2.5 cm) front-to-back or side-to-
side at the belt path. If the child seat is not secure,
repeat the installation process or use an alternate
seating location.
When properly installed in the rear-facing position,•
the back angle of the child seat should be 30º – 45º
from vertical (not to exceed 45º) when the car is
parked on a level surface (Fig. H).
If necessary, the proper recline angle can be•
achieved by placing a rolled towel or pool noodle in
the vehicle seat bight to level the child seat’s base.
Rear-facing installation can be improved by the use•
of the Versa-Tether. See pages 25 – 28.
G
F
E
LATCH Installation
Figure A illustrates a rear-facing LATCH•
installation.
Verify that your vehicle is equipped with LATCH•
anchors. If LATCH anchors are not available, you
must use the vehicle belt installation methods.
If stored, remove the LATCH connectors from1
the storage slots under the cover (page 29)
and pass them through their adjacent belt slots.
Press and hold the first LATCH adjuster2
release button, then pull the LATCH strap to
full length. Repeat for the remaining LATCH
connector.
Recline the child seat and place rear-facing on3
the vehicle seat. This child seat must be in the
recline position when installed rear-facing. See
Recline Adjustment on page 29.
Attach one LATCH connector to its adjacent4
vehicle LATCH anchor (Fig. B) in the upright
position (Fig. C).
An audible click confirms attachment.•
Ensure that the LATCH strap is not twisted.•
TIP: You may need to turn the front of the child
seat toward you for easier access to the
vehicle LATCH anchor.
Attach the remaining LATCH connector to its5
adjacent vehicle LATCH anchor (Fig. D) in the
upright position (Fig. C).
An audible click confirms attachment.•
Ensure that the LATCH strap is not twisted.•
NOTE: If an audible click is not heard when
connecting either LATCH connector, the LATCH
strap may be twisted, or there may be debris in the
LATCH connector. Correct either situation before
continuing with the installation process.
Align each LATCH strap on the LATCH bar6 D
A
B
H
WARNING! Do not raise the child
seat off the front edge of the vehicle seat.
This could cause your child seat not to
perform as intended.
C
Release
Button Top

14
15
Installation: Rear-Facing Installation: Rear-Facing
Lap-Shoulder Belt Installation
Figure A illustrates a rear-facing, lap-shoulder•
belt installation.
When not in use, always store the LATCH•
connectors in the storage slots. See page 29.
Recline the child seat then place it rear-facing1
on the vehicle seat. This child seat must be in
the recline position when installed rear-facing.
See Recline Adjustment on page 29.
Lift the cover to open the rear-facing lock-off2
farthest from where the vehicle belt will be
buckled (Fig. B).
Pull the vehicle belt out, then pass it3 under the
LATCH bar and through the rear-facing belt
slot (Fig. C).
The vehicle belt can be routed over or under•
the cover.
Route the vehicle belt across seat then4
through the opposite rear-facing belt slot and
under the LATCH bar.
IMPORTANT: The vehicle belt must rest behind the
child seat buckle strap.
Verify that the vehicle belt is not twisted,5
position the lap belt portion through the open
lock-off, then buckle (Fig. D).
Push the child seat firmly into the vehicle seat6
while removing slack first from the lap portion
of the vehicle belt, then the shoulder portion
(Fig. E).
Position the shoulder portion of the vehicle7
belt through the open lock-off, tighten belt,
close the lock-off arm (Fig. F), and replace the
cover.
The lock-off is properly closed when a click is•
heard.
To prevent damage, never extend the lock-off arm•
beyond its normal open position and always keep
the lock-off closed when it is not in use.
If your vehicle is equipped with an automatic•
locking retractor (ALR), use of lock-offs is not
required as long as the ALR is locked. Check your
vehicle owner’s manual to determine the type of
retractor your vehicle has, and how to lock the
retractor.
Verify that vehicle belt is tight and that the child8
seat is secure.
The child seat is secure when it cannot be moved•
more than 1 in. (2.5 cm) front-to-back or side-to-
side at the belt path. If the child seat is not secure,
repeat the installation process or use an alternate
seating location.
When properly installed in the rear-facing position,•
the back angle of the child seat should be 30º – 45º
from vertical (not to exceed 45º) when the car is
parked on a level surface (Fig. G).
If necessary, the proper recline angle can be•
achieved by placing a rolled towel or pool noodle in
the vehicle seat bight to level the child seat’s base.
Rear-facing installation can be improved by the•
use of the Versa-Tether. See pages 25 – 28.
A
B F
C G
D
WARNING! Do not raise the child seat off the front edge of
the vehicle seat. This could cause your child seat not to perform as
intended.
E
2
1

16
17
If your vehicle is equipped with an automatic•
locking retractor (ALR), use of the lock-offs is not
required as long as the ALR is locked. Check your
vehicle owner’s manual to determine the type of
retractor your vehicle has, and how to lock the
retractor.
Verify that vehicle belt is tight, locked, and that8
the child seat is secure.
The child seat is secure when it cannot be moved•
more than 1 in. (2.5 cm) front-to-back or side-to-
side at the belt path. If the child seat is not secure,
repeat the installation process or use an alternate
seating location.
When properly installed in the rear-facing position,•
the back angle of the child seat should be 30º – 45º from vertical (not to
exceed 45º) when the car is parked on a level surface (Fig. F).
If necessary, the proper recline angle can be achieved by placing a rolled•
towel or pool noodle in the crease of the vehicle seat to level the child seat’s
base.
Rear-facing installation can be improved by the use of the Versa-Tether. See•
pages 25 – 28.
Lap-Belt Installation
Figure A illustrates a rear-facing, lap-belt•
installation.
When not in use, always store the LATCH•
connectors in the storage slots. See page 29.
Recline the child seat, then place it rear facing on1
the vehicle seat. This child seat must be in the
recline position when installed rear-facing. See
Recline Adjustment on page 29.
Lift the cover and open the rear-facing lock-2
off farthest from where the vehicle belt will be
buckled (Fig. B).
Pull the vehicle belt out, then pass it3 under the
LATCH bar and through the rear-facing belt slot
(Fig. C).
The vehicle belt can be routed over or under•
cover.
Route the vehicle belt across the child seat then4
through the opposite rear-facing belt slot and
under the LATCH bar.
IMPORTANT: The vehicle belt must rest behind the
child seat buckle strap.
Verify that the vehicle belt is not twisted, position5
the belt through the open lock-off, then buckle
(Fig. D).
Push the child seat firmly into the vehicle seat6
while removing slack from the vehicle belt.
Tighten the belt, close the lock-off arm, and7
replace the cover (Fig. E).
The lock-off is properly closed when a click is•
heard.
To prevent damage, never extend the lock-off arm•
beyond its normal open position and always keep
the lock-off closed when not in use.
Installation: Rear-Facing Installation: Rear-Facing
A E
B F
C
D
WARNING! Do not use this seat
with a non-locking, two-point Emergency
Locking Retractor (ELR) vehicle belt.
WARNING! Do not raise the child seat off the front edge of
the vehicle seat. This could cause your child seat not to perform as
intended.

18
19
Installation: Forward-Facing Installation: Forward-Facing
Attach the remaining LATCH connector to its6
adjacent vehicle LATCH anchor (Fig. D) in an
upright position (Fig, C).
An audible click confirms attachment.•
Ensure that the LATCH strap is not twisted.•
NOTE: If an audible click is not heard when
connecting either LATCH connector, the LATCH
strap may be twisted, or there may be debris in the
LATCH connector. Correct either situation before
continuing with the installation process.
Push the child seat firmly into the vehicle seat7
while pulling each LATCH strap tight (Fig.
E).
IMPORTANT: Ensure the LATCH strap does not
fold into the LATCH adjuster while tightening.
Attach the Versa Tether8 ®hook to the vehicle’s
designated tether anchor for the chosen
seating position. Remove all slack from the
tether to secure. Store excess webbing in the
tether pouch. See pages 25 – 28.
Verify that all connections are secure and that the child seat is stable.9
The child seat is secure when it cannot be moved front- to-back or•
side-to-side more than 1 in. (2.5 cm) at the belt path. If the child seat is
not secure, repeat the installation process or use an alternate seating
location.
E
D
B
If stored, remove the LATCH connectors from1
the storage slots under the cover (page 29)
and pass them through their adjacent belt slots.
Press and hold the first LATCH adjuster2
release button, then pull the LATCH strap to
full length. Repeat for the remaining LATCH
connector.
Remove the Versa-Tether from the pouch and3
place it up and over the child seat back.
Place the child seat forward-facing on the4
vehicle seat.
TIP: You may need to raise or remove the vehicle
head restraint to achieve best fit of the child seat.
Attach one LATCH connector to its adjacent vehicle LATCH anchor5
(Fig. B) in the upright position (Fig. C).
An audible click confirms attachment.•
Ensure that the LATCH strap is not twisted.•
TIP: You may need to turn the back of the child seat toward you for
easier access to the vehicle LATCH anchor.
LATCH Installation
Figure A illustrates a forward-facing LATCH•
installation.
Verify that your vehicle is equipped with•
LATCH anchors. If LATCH anchors are not
available, you must use vehicle belt installation
methods.
A
WARNING!
This child seat must not be used forward-facing•
for children less than one year of age OR who
weigh less than 20 lbs (9.1 kg).
This child seat must be in full upright position•
when installed forward-facing for children who
weigh more than 33 pounds (15.1 kg).
WARNING! Refer to your vehicle owner’s manual or
contact the vehicle manufacturer for the maximum weight rating for
their LATCH anchors. Use vehicle belt (not LATCH connectors) for
installations with children who weigh more than the vehicle LATCH
anchor limit. Unless specified otherwise by the vehicle manufacturer,
assume a 40 lbs (18.1 kg) child is the vehicle LATCH anchor limit.
C
Release
Button Top

20
21
Verify that the vehicle belt is not twisted and5
is routed over the LATCH bars, then buckle
(Fig. D).
Push the child seat firmly into the vehicle seat6
while removing slack first from the lap portion
of the vehicle belt, then the shoulder portion
(Fig. E).
Hold the shoulder belt tight, then rotate the lock-7
off until the vehicle belt is secured (Fig. F).
If your vehicle is equipped with an automatic•
locking retractor (ALR), use of lock-offs is not
required as long as the ALR is locked. Check
your vehicle owner’s manual to determine the
type of retractor your vehicle has, and how to lock
the retractor.
Attach the Versa-Tether8 ® hook to the designated
tether anchor (if available according to the vehicle
owner’s manual) for the chosen seating position.
Remove all slack from the tether to secure. Store
excess webbing in the tether pouch. See pages
25 – 28.
Verify that the vehicle belt is tight and the child9
seat is secure.
The child seat is secure when it cannot be•
moved front-to-back or side-to-side more than
1 in. (2.5 cm) at the belt path. If the child seat
is not secure, repeat this procedure or use an
alternate seating location.
F
2
1
E
Installation: Forward-Facing Installation: Forward-Facing
Lap-Shoulder Belt Installation
Figure A illustrates a forward-facing lap-shoulder•
belt installation.
When not in use, always store the LATCH connectors•
in the storage slots. See page 29.
WARNING!
This child seat must not be used forward-facing•
for children less than one year of age OR who
weigh less than 20 lbs (9.1 kg).
This child seat must be in full upright position•
when installed forward-facing for children who
weigh more than 33 pounds (15.1 kg).
If the vehicle is equipped with a designated1
tether anchor for the chosen seating position,
remove the Versa-Tether from the pouch and
place it up and over the child seat back.
IMPORTANT: Britax recommends that the Versa-Tetherbe
used at all times. Using the tether will improve the stability
of the child seat and reduce the risk of injury. Check your
vehicle owner’s manual for approved tether locations.
Place the child seat forward-facing on the vehicle2
seat. Ensure the bottom of the child seat base is in full
contact with the vehicle seat.
TIP:You may need to raise or remove the vehicle head
restraint to achieve best fit of the child seat.
Rotate the lock-off lever to open the forward-facing lock-off farthest3
from where the vehicle belt will be buckled.
Pull vehicle belt out, then pass it4 over the LATCH bar, through the
forward-facing belt path, then over the LATCH bar on the opposite
side (Fig. B).
TIP:Turning the back of the child seat toward you can make routing the vehicle
belt easier (Fig. C).
D
AForward-Facing
B
C

22
23
Installation: Forward-Facing Installation: Forward-Facing
Pull the vehicle belt out, then pass it4 under
the LATCH bar, through the forward-facing
belt path, then under the LATCH bar on the
opposite side (Fig. B).
TIP:Turning the back of the child seat toward you can
make routing the vehicle belt easier (Fig. D).
Verify that the vehicle belt is not twisted, is5
routed under the LATCH bars, then buckle
(Fig. B).
Push the child seat firmly into the vehicle seat6
while removing slack from the vehicle belt
(Fig. C).
AttachtheVersa-Tether7 ®
hooktothedesignated
tether anchor (if available according to the
vehicle owner’s manual) for the chosen
seating position. Remove all slack from the
tether to secure. Store excess webbing in the
tether pouch. See pages 25–28.
Verify that the vehicle belt is tight, locked and8
the child seat is secure.
The child seat is secure when it cannot be•
moved front-to-back or side-to-side more than 1
in. (2.5 cm) at the belt path. If the child seat is not
secure, repeat this procedure or use an alternate
seating location.
Lap-Belt Installation
Figure A illustrates a typical forward-facing, lap-•
belt installation.
When not in use, always store the LATCH•
connectors in the storage slots. See page 29.
If the vehicle is equipped with a designated1
tether anchor for the chosen seating position,
remove the Versa-Tether from the pouch and place it up and over the
child seat back.
IMPORTANT: Britax recommends that the Versa-Tether be used at all times.
Using the tether will improve the stability of the child seat and reduce the risk of
injury. Check your vehicle owner’s manual for approved tether locations.
Place the child seat forward-facing on the vehicle seat. Ensure the2
bottom of the child seat base is in full contact with the vehicle seat.
TIP:You may need to raise or remove the vehicle head restraint to achieve
best fit of the child seat.
If the vehicle is equipped with a designated tether anchor for the3
chosen seating position, remove the Versa-Tether from the pouch and
place it up and over the child seat back.
BD
AForward-Facing
WARNING!
This child seat must not be used forward-•
facing for children less than one year of age
OR who weigh less than 20 lbs.
This child seat must be in full upright position•
when installed forward-facing for children
who weight more than 33 lbs (15.1 kg).
WARNING! Do not use this seat
with a non-locking, two-point Emergency
Locking Retractor (ELR) vehicle belt.
C

24
25
Installation: Aircraft Installation: Versa-Tether®
This child seat is certified for aircraft use. Most
airlines in the U.S. and Canada will allow the use of
a child seat as long as it is labeled as an approved
child seat for airline use and fits properly on the
aircraft seat. Contact the airline about their policy
prior to traveling.
Safety Information
A
B
WARNING!
When using the child seat in forward-facing mode, attach the Versa-•
Tether only to tether anchors designated by the vehicle manufacturer
as tether anchorage points. Use of other locations is not approved
or permitted.
DO NOT modify the vehicle without advice from the vehicle•
manufacturer if a tether anchorage is not available.
IMPORTANT:
Britax recommends that the tether be used at all times. Using the•
tether will improve the stability of the child seat and reduce the risk
of injury.
If your vehicle does not currently have a tether anchor attachment,•
refer to your vehicle owner’s manual or contact the vehicle
manufacturer for assistance.
The FAA recommends that a child weighing up to 40 pounds (18.1 kg)
use a certified, harnessed child seat while traveling on an aircraft.
Install your child seat in a window seat to avoid blocking the aisle.
If the aircraft lap belt is too short, ask the flight attendant for a belt
extender.
Rear-Facing Installation
For rear-facing aircraft installation (Fig. A), follow
Rear-Facing Lap-Belt Installation instructions
on pages 16–17.
To aid installation on aircraft, open the rear-4
facing lock-offs to allow routing of large
buckles.
Forward-Facing Installation
For forward-facing aircraft installation (Fig. B),
follow Forward-Facing Lap-Belt Installation
instructions on pages 22–23.

26
27
Installation: Versa-Tether®Installation: Versa-Tether®
Using the Versa-Tether
Consult your vehicle owner’s manual for1
designated tether anchorage locations.
Locate the tether on the rear of the child seat2
and remove the tether from the pouch.
Place the tether up and over the child seat3
back.
Installthe childseat using theLATCH system or4
the vehicle belts according to the instructions
in this manual.
Tilt the tether release tab then pull to fully5
extend the tether strap into a “V” shape.
Locate the hook on the strap and attach the6
tether hook to the vehicle’s designated tether
anchor.
See figure A for a forward-facing installation.•
See figures B and C for a rear-facing•
installation.
IMPORTANT: The tether should be hooked over,
not under, the vehicle tether anchor.
Pull the tether adjuster strap to remove all7
slack. Roll up excess webbing and store in
tether pouch.
Verify there is tension in the tether strap and8
that child seat is properly secured.
The child seat is secure when it cannot be•
moved front-to-back or side-to-side more than
1 in. (2.5 cm) at the belt path.
Tether Connector Strap
OR
A
OR
B
C
WARNING! Only use the tether connector strap for a rear-
facing tether installation.
Because every vehicle model is different,
sometimes you cannot find a location to
properly anchor the tether. Use the tether
connector strap to assist in creating an anchor
point (Fig. D).
Find a fixed vehicle anchor point that is1
bolted to the floor.
If you cannot find an acceptable location to•
create an anchor point, contact the vehicle
manufacturer to identify a suitable tether
connection point.
Route the strap around the fixed vehicle2
anchor point.
Take the metal D-ring and thread it through3
the webbing loop on the other end of the
strap (Fig. D).
Pull the metal D-ring all the way through until4
the strap is tight.
Use the D-ring as an attachment point for5
the hook on the tether strap.
NOTE: Store the tether connector strap in the
tether pouch when not in use.
D

28
29
Installation: Versa-Tether®Child Seat Functions
Figure A shows the tether when the child seat
is acceptable for continued use (provided the
child seat has not been involved in a crash). The
colored stitching will be intact and the webbing
will be looped inside the shell.
Figures B and C show the tether when the child
seat is unacceptable for continued use. If any of
the loops have pulled through the back side of the
shell and/or any of the colored stitching has been
released on either side, the child seat is no longer
acceptable for use. Discontinue use of the child
seat.
IMPORTANT: Regardless of whether loops have
pulled through the back side of the shell and the
colored stitching has been released, discontinue use
of the child seat if it has been involved in a moderate
or severe crash.
Energy-Absorbing Versa-Tether®
The energy-absorbing Versa-Tether was designed to enhance
the performance of the child seat tether. By introducing a staged
release of the tether webbing, the forward movement of the child
seat is delayed while reducing the amount of energy transferred to
the child seat during a crash. A secondary benefit of the energy-
absorbing Versa-Tether is to help indicate when the child seat has
been involved in a moderate or severe crash and replacement of the
child seat is necessary.
A
B
C
Storing the LATCH Connectors
When the LATCH connector is not in use, lift the cover
to access the LATCH storage slots (Fig. D). Fold the
LATCH adjuster and the connector, then slide each
set into the adjacent slot.
NOTE: Child seats are shipped from Britax with the
LATCH connectors in the storage slots. You will have
to open the rear-facing lock-offs to remove the LATCH
connectors from storage.
Recline Adjustment
Pull the recline handle (Fig. E) then slide the child
seat shell into the desired position. Release the
recline handle, then verify the child seat has locked
into position.
E
D
NOTE: It will be necessary to loosen the tether, vehicle seat belt, and/or
LATCH strap before adjusting the recline position. The tether, vehicle seat
belt, and/or LATCH strap must be properly re-tightened after adjusting the
recline position.
WARNING!
This child seat must be in the recline position•
when installed rear-facing.
Child seat must be in full upright position•
when installed forward-facing with children
who weigh more than 15 kg (33 lbs) optional
only for rear-facing use.

30
31
C
Chest Clip
Fastening the Chest Clip
Fasten the chest clip by pushing the two halves
together until a positive click is heard (Fig. A).
Releasing the Chest Clip
Squeeze the middle tabs together (Fig. B).1
Pull the two pieces apart.2
Adjusting the Chest Clip
Slide the chest clip up or down (Fig. C) on the1
harness so it is positioned at the middle of the
child’s chest, level with the child’s armpits.
Slide the HUGS2 ™chest pads and comfort pads
to a comfortable location for the child.
HUGS™ Chest Pads
Child Seat Functions Child Seat Functions
WARNING! HUGS™chest pads must
be installed for forward-facing use. Removal of
HUGS is optional only for rear-facing use.
B
A
Harness Buckle
Fastening the Harness Buckle
Hold the harness buckle with one hand.1
Use your other hand to insert one buckle tongue2
at a time into the harness buckle (Fig. D).
A proper connection is confirmed with a positive•
click after inserting each buckle tongue.
Releasing the Harness Buckle
Brace the rear of the harness buckle with one1
hand.
Use your thumb to press the release button and2
slide both buckle tongues to remove from the
buckle (Fig. E).
IMPORTANT: Periodically clean the harness buckle to
ensure safe operation (page 37).
x 2
x 2
E
x 2
x 2
D
Adjusting Harness Slot Height
IMPORTANT: See Important Harness Adjustments on
pages 6–7 for instructions on proper harness fit based
on your child’s height and weight.
Loosen the harness by lifting the harness adjuster1
lever while pulling the harness straps forward as
far as possible (Fig. F).
From the rear of the child seat, unhook the shoulder2
harness from the harness yoke (Fig. G).
Pull the harness straps through the shell, foam,3
and cover to the front of the child seat.
Thread the harness straps through the appropriate4
harness slots in the cover, foam, and child seat
shell (Fig. H).
Reattach the harness straps to the harness yoke5
(Fig. G).
Pull the harness-adjuster strap to tighten the6
harness.
Verify that all straps are threaded at the same7
height and are not twisted.
F
G
H

32
33
Buckling and Tightening the Harness
Loosen the harness by lifting the harness1
adjuster release lever located on the front
of the child seat while pulling both shoulder
straps forward (Fig. A).
Release the chest clip by squeezing the tabs2
and sliding the pieces apart (Fig. B).
Unfasten the harness buckle by pressing the3
release button and sliding the tongues out.
Move the harness straps to the side of the4
child seat.
Use the harness holders located on the straps•
and both sides of the cover to aid in holding
the straps.
IMPORTANT: Remove bulky coats and/or jackets
before putting the child in child seat. Adjust the
harness to fit the clothes the child is wearing.
Place child in the child seat.5
Position harness straps around the child and6
fasten harness buckle (Fig. C) and chest clip
(Fig. D).
Proper connection of the harness buckle is•
confirmed with a positive click after inserting
each buckle tongue.
If the buckle will not fasten with an audible•
click after insertion of each buckle tongue,
the harness buckle or adjuster area may
be clogged with food, drink or other debris
that needs to be removed. See page 37 for
cleaning instructions.
A
Securing Your Child Securing Your Child
Slide the HUGS7 ™chest pads down towards the buckle.
Important checklist before tightening the harness:
Check for proper harness height (see pages 6 – 7).9
Remove slack from around the child’s upper thighs.9
Remove slack between the Hugs™ chest pads and the buckle.9
B
C
D
Slowly pull the adjuster strap8
until the harness is snug
around the child. The harness
adjuster will click when the
harness is snug.
NOTE: The Click & Safe™ Snug
Harness Indicator is an audible aide
to help determine when the harness
is within range of appropriate
snugness. When tightening the
harness, this audible click provides
extra assurance that the harness is snug.
A snug strap should not allow any slack. It lies•
in a relatively straight line without sagging. It
does not press on the child’s flesh or push the
child’s body into an unnatural position.
You should not be able to pinch excess•
webbing at the shoulder once the harness is
properly secured.
If there is still slack in the harness, review the9
checklist and then pull the harness adjuster
strap again until another click indicates a snug harness.
Position the chest clip at the middle of the child’s chest, level with the10
child’s armpits (Fig. E).
Verify that the harness is not twisted and the child is properly11
secured.
IMPORTANT: Always pull on the harness after securing the child to ensure
the buckle tongues are secure in the harness buckle.
E
Pull the harness adjuster away from
the child seat to tighten.
Do not pull sideways.

34
35
Care and Maintenance
Cover Removal
Loosen the harness by lifting the harness1
adjuster lever while pulling the shoulder straps
forward as far as possible.
Unhook the shoulder straps from the harness2
yoke on the rear of the child seat (Fig. A).
Pull the upper harness straps through the shell3
and cover to the front of the child seat.
Remove the buckle and belly pad (page 36).4
Gently remove the upper portion of the cover. Be careful not to5
damage the energy-absorbing foam.
Pull the lower harness straps, buckle tongues, HUGS6 ™chest pads,
and chest clip through the lower slots in cover.
Remove the entire cover from the child seat.7
For additional demonstration please visit www.BritaxUSA.com.
Refitting the Cover
To refit the cover, reverse the above directions. Make sure that the
shoulder straps are not twisted, and are threaded properly through
the chest clips, cover, foam and shell.
WARNING! Do not take apart the harness. Never
remove the buckle tongues from the harness. They
cannot be reattached after removal. If reassembled incorrectly,
the child seat may not perform as intended.
A
Care and Maintenance
Cleaning the Cover
HAND WASH using cold water and mild soap.•
LINE or LIE-FLAT DRY to prevent the cover from shrinking.•
DO NOT• bleach, machine wash, machine dry or iron.
Cleaning the Shell
SPONGE CLEAN using warm water and mild soap.•
TOWEL DRY•
DO NOT• use solvents or abrasive cleaners.
Cleaning the Harness
SPONGE CLEAN using warm water and mild soap.•
TOWEL DRY•
DO NOT• bleach, machine wash, machine dry or disassemble
the harness.
Cleaning the Harness Adjuster
Periodically check the adjuster area to be sure it is clean and free of
food, drink or other debris. If debris is present, it must be removed to
prevent interference with the adjuster mechanism.
BRUSH AWAY LOOSE DEBRIS using a soft-bristled brush.•
SPONGE CLEAN using warm water and a mild soap.•
TOWEL DRY•
DO NOT• use solvents, abrasive cleaners or disassemble the
harness.

36
37
Care and Maintenance Care and Maintenance
Harness Buckle Removal
Fully recline the child seat.1
Locate the metal buckle strap retainer on the2
bottom of the child seat.
Pull the retainer away from the child seat to3
loosen.
Turn the retainer so the short side will fit through4
the slot in the child seat shell (Fig. A).
Push the retainer through the slots in the shell and cover, to the top5
of the child seat.
Re-threading the Harness Buckle
Locate the slot in cover and shell for the harness buckle.1
Turn the buckle retainer so the short side will fit through the slot in the2
cover and the child seat shell (Fig. A).
Push the retainer through the slots in the shell and cover, to the bottom3
of the child seat.
Pull the harness buckle away from the child seat until tight and verify4
the strap is not twisted and the release button is facing outward.
A
Cleaning the Harness Buckle
If a child eats and drinks while in the child seat,
the harness buckle may need to be periodically
checked and cleaned of any food, drink or other
debris.
REMOVE BUCKLE as described on page 36.•
THOROUGHLY RINSE using warm water (Fig. B).•
TEST THE HARNESS BUCKLE by fastening•
(Fig. C) and unfastening (Fig. D) until a positive
click is heard after inserting each buckle
tongue. If either click is not heard, repeat
cleaning procedure.
TOWEL DRY•
DO NOT• lubricate, use solvents, abrasive
cleaners, soap or other household detergents.
B
x 2
x 2
D
x 2
x 2
C