Broadata LBH-SDI-EAD-T User manual

LBH-SDI-EAD-T
LINK BRIDGETM HDBASET
SDIVIDEO CONVERTING
TRANSMITTER SYSTEM
BCI reserves the right to make changes to the products described herein without
prior notice or consent. No liability is assumed as a result of their use or
application. All rights reserved.
©2013 Broadata Communications, Inc.

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 3
CAUTION
This symbol alerts the user that important literature concerning the
operation of this unit has been included. Therefore, it should be read carefully
in order to avoid potential problems.
Manufacturer: This symbol shall be accompanied by the name and
address of the manufacturer adjacent to the symbol, and the date of
manufacture where the date shall be located adjacent to the symbol.
SN Serial Number: Indicates the manufacturer’s serial number so that a
specific medical device can be identified.
CLASS II ME EQUIPMENT
Functional Earth Terminal.
Caution, review manufacturer’s documentation for instructions.
WARNING: No modification of this equipment is allowed. DO NOT remove
cover (or back). There are no user serviceable parts inside. Refer servicing
to qualified service personnel.
Product Safety:
This product meets the medical safety requirements.
North American Safety Compliance:
ANSI/AAMI ES60601-1:2005/(R):2012 Medical electrical equipment – Part 1:
General requirements for basic safety and essential performance
CAN/CSA-C22.2 No. 60601-1-08 (3rd Ed.) Medical electrical equipment –
Part 1: General requirements for basic safety and essential performance
WITH RESPECT TO ELECTRIC SHOCK, FIRE AND MECHANICAL
HAZARDS ONLY

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
4
EEC Safety Compliance:
These products meet the requirements of EN 60601-1:2005 so as to conform
to the Medical Device
Directive93/42/EEC (generalsafety information)as amendedby 2007/47/EC.
This equipment is energized from 100-240 VAC 50 / 60 Hz power source. It is
the responsibility of the installer to ensure that the equipment is installed in
accordance with applicable hospital, local and national electrical codes. An
additional multiple socket-outlet or extension cord shall not be connected to
the system
To power unit down, remove power cable from unit or disconnect power cord
from power receptacle. The power supply or the appliance coupler is the only
recognizeddisconnect device,disconnectthepowersupply fromtheAC mains.
Do not position the equipment so that is it is difficult to access the appliance
coupler.
Class II Medical System
No Applied Parts
IP20
LBH Power Supply:
80275-2401 [email protected] Power Supply
For medical applications must use:
MPS-24V 30W-BP (BCI-80275-2475): BridgePower 24V D/T 2.5mm 100-
240V~, 50-60Hz 1.0A LCK MED
MPS-24V-50W-GLT (BCI-80275-2421): GlobTek 24V D/T 2.5mm 100-240V~,
50-60Hz 1.6A LCK MED
Power Cord: Use a hospital grade power cord with the correct plug for your
power source.
Recycling:
Upon termination of the service life of this product please return unit to the
manufacturer for proper waste disposal, or follow local governing ordinances
and recycling plans regarding the recycling or disposal of this equipment , or
contact the Electronic IndustriesAlliance (www.eiae.org).
Declarations of Conformity
FCC and Council Directives of European Standards:
This device complies with Part 15 of FCC rules and 93/42/EEC of the Council
Directives of European Standards Directive as amended by 2007/47/EC.
Operation is subject to the following two conditions: (1) This device may not

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 5
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesirable results.
1. Use the specified cables with this device so as not to interfere with radio
and television reception. Use of other cables and / or adapters may cause
interference with other electronic equipment.
2.This equipmenthas beentested andfoundto complywith thelimits pursuant
to FCC part 15 and CISPR 11. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance
withthe instructions,may causeharmful interferenceto radiocommunications.
IEC:
Thisequipment hasbeen testedand foundto complywith thelimitsfor medical
devicesto theIEC 60601-1-2.These limitsare designedto providereasonable
protection against harmful interference in a typical medical installation. This
equipment generates, uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to other devices in the vicinity.
FCC, Council Directives of European Standards and IEC:
Thereis noguarantee thatinterference willnot occurinaparticularinstallation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
Accessory equipment connected to this monitor must be certified according
to the respective IEC Standards (i.e., IEC 60950-1) for data processing
equipment and IEC 60601-1 for medical equipment). Anyone who connects
additional equipment to the signal input part or signal output part configures
a medical system, and is therefore responsible that the system complies with
the requirements of system standard IEC 60601-1-1. Whoever is responsible
for securing the monitor to a system needs to insure that the mounting
equipment used with this display complies to IEC standard 60601-1. If in
doubt, consult the technical services department or your local representative.

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
6
About this Manual
Thismanual isdesigned toassistthe userwith installation,setup andoperation
of the LBH product series. The functional descriptions in this manual are
representative of:
60722-0800 LBH-SDI-EAD-T
60722-2800 LBH-SDI-EAD-T-WP
Manual ID Number: 60000-LBHSDI-EAD-080814
Intended Use and Contraindications
Intended Use:
This device is intended for use in a medical environment to transmit high
quality video and graphic images . Suitable for Continuous Use. All parts of
the system are suitable for use within the patient environment
Contraindications:
This device is not intended for life support applications.
Not suitable for use in an oxygen rich environment
Operational Failure Conditions and Mitigation
Operational Failure:
End user cannot view the video data from a connected video source due to
Incompatibility with video source equipment, or degraded video data, or the
unit cannot be powered on.
Mitigation:
Bypass the device by connecting via a failsafe cable from the output of the
video source directly to a monitor.
For mission critical applications, we strongly recommend that a replacement
unit be immediately available.
SURGE PROTECTION DEVICE RECOMMENDED
This product contains sensitive electrical components that may be damaged
by electrical spikes, surges, electric shock, lightning strikes, etc. Use of
surge protection systems is highly recommended in order to protect and
extend the life of your equipment.

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 7
TABLE OF CONTENTS
1.0 PRODUCT DESCRIPTION .............................................6
2.0 SETUP..............................................................................9
2.1 MOUNTING......................................................................9
2.2 CABLING AND CONNECTORS......................................9
2.2.1 ELECTRICAL CABLE CONNECTIONS .....................10
2.2.1.1 SDI VIDEO INTERFACE ...........................................10
2.2.1.2 AUDIO INTERFACE ..................................................11
2.2.1.3 SERIAL DATA INTERFACE .......................................12
2.2.1.4 STATUS LED’S .........................................................13
2.2.2 CAT-5e/6 CABLE CONNECTION ...............................13
2.3 DC POWER CONNECTION.........................................15
2.5 IN-WALL POWER/CAT-5e/6 WIRING INSTRUCTION 16
3.0 OPERATION...................................................................19
4.0 MAINTENANCE AND TROUBLESHOOTING..............20
4.1 MAINTENANCE .............................................................20
4.2 TROUBLESHOOTING ..................................................20
5.0 SPECIFICATIONS..........................................................22
6.0 SERVICE PROCEDURE ...............................................24
6.1 REPLACEMENT POLICY .............................................24
6.2 RETURN AND REPAIR SERVICE .................................24
7.0 LIMITED WARRANTY ....................................................25

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
8
1.0 PRODUCT DESCRIPTION
TheLBH-SDI-EAD-TSeriesis a highperformance,lowcost, miniature,
Link BridgeTM HDBaseT SDI Transmission System. It carries one (1)
unidirectionalSDIvideo,one(1) unidirectional embedded stereoaudio
and two (2) bi-directional RS-232 and one (1) bi-directional IR through
oneCAT-5e/6. TheTXunitcanpowertheopposite sideovertheCAT-5e/
6cable,viaPoH (PowerOverHDBT).This unique transmissionsystem
letsyourdigitalflat panel displayextendat4K2K Ultra HDandWUXGA
(1920x1200@60Hz)or720p/1080i/1080pHDTVvideoresolution.
No user adjustment is required for the LBH-SDI-EAD-T system due to
theuseofadvanced digital HDBTtransmissionsystemtechnology with
zero compression and zero bit reduction. This allows for a quick and
easy setup, offering trouble-free operation for many years to come. In
addition,the LBH-SDI-EAD-Ttransmitter iscompatiblewithour LBH-EAD
Series receiver such as LBH-DVI-EAD-R or LBH-HDMI-EAD-R. This
makesbothHDBT transmissionandHDMI/DVI/VGA/YPbPr/SV/CV/SDI
conversion in one single system setup. The LBH-SDI-EAD-T comes
with either a standalone miniature enclosure or a Decora wall-plate
packaging. The units are easily monitored by power and link LED
indicators.
Figures 1-1, 1-2, 1-3 and 1-4 illustrate the front and rear panels of
theLBH-SDI-EAD-Tunit.

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 9
Figure 1-2
LBH-SDI-EAD-T Rear Panel
1.5AMP
+24VDC
LINK
CAT-5e/6
Output Connector
Power
Connector
FRONT PANEL (STANDALONE)
REARPANEL(STANDALONE)
Figure 1-1
LBH-SDI-EAD-T Front Panel
Power
Link LED Data
Out Data
In SPDIF In
Audio In
SDI In

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
10
FRONT PANEL (WALLPLATE)
Figure 1-3
LBH-SDI-EAD-T-WP Front Panel
REARPANEL(WALLPLATE)
Figure 1-4
LBH-SDI-EAD-T-WP Rear Panel
+24V
Power
Connector
CAT-5e/6
Connector
Power
Link LED
Data/IR
Out
Data/IR
In
SPDIF In
Audio
In
SDI In

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 11
2.0 SETUP
LBH-SDI-EAD-Tisatransmitterthatcanbe paired with any DVI/HDMI
centric LBH receiver (such as LBH-HDMI-R). One LBH-SDI-EAD-T
transmitter unit is located at the near-end and connected through one
CAT-5e/6,totheLBH-HDMI-EAD-Rreceiverlocatedatthe far-endofthe
link. Figure 2-1 depicts a typical installation for the LBH-SDI-EAD-T.
Figure 2-1
LBH-SDI-EAD-T/RSetup
2.1 Mounting
Beforeinstallingtheunitsintoyour housing, make surethereis
enough space to pull and connect both the electrical and
CAT-5e/6 transmission cables without stressing them beyond
themanufacturer’slimitations (alsoknownastheminimumbend
radius).
2.2 Cabling and Connectors
In order to setup the LBH-SDI-EAD-T properly, make sure to
observe the following instructions when installing the proper
cables. TheLBH-SDI-EAD-Trequirestwopartstothe cabling
setup, the electrical and the CAT-5e/6 transmission.

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
12
2.2.1 Electrical Cable Connection
Thethreeavailable cable connectionsonthe electrical sideare
forSDIvideo,audioanddataconnections. Followtheproceeding
instructions in order to properly install your electrical
connections.
2.2.1.1 SDI Video Interface
The SDI video connection is the SDI plug connectors for
videoinputandoutput ports. Usethefollowinginstructions
to properly connect your component video as illustrated in
Figure 2-2.
1. Connect the LBH-SDI-EAD-T (Transmitter) unit’s SDI
videoinputport totheuser’s VGAvideosource withthe
appropriateHDMIcables.
2. For the receive unit, connect the LBH-HDMI-EAD-R
(Receiver) HDMI video output port to the user’s HDMI
video receivers with the appropriate HDMI cables
respectively, as illustrated in Step 1.
Figure 2-2
Video Connection
User’s SDI
Video Source User’s SDI
Video Source

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 13
2.2.1.2Audio Interface
Theaudiointerfacesupports single stereochannelhighfidelity
transmissions. One stereo channel is transmitted in one
direction. Line-level audio signals are connected to the
LBH-SDI-EAD-T units. The following steps illustrate the
installationproceduresforaudio devices.
To send audiosignals,labeland connect onestereoaudio-jack
cableto the“AUDIO OUTPUT”connector andthe linelevel audio
receiver, connect the other cable to the front panel stereo jack
connectorlabeled“AUDIO IN”(seeFigure 2-3aand2-3b) tothe
linelevelsource.
Figure 2-3a
Audioinput to
LBH-SDI-EAD-Tunit
Figure 2-3b
Audio output from
LBH-HDMI-EAD-Runit
User’s
Audio Output User’s
Audio Input
LBH-HDMI-EAD-Rx
Out
L/R
SPDIF
OUT
HDMI
HDCP
LINK
PWR/
DATA
DATA
AUDIO
IR
12543 L/R
SPDIF
In
1
122

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
14
2.2.1.3 Serial Data Interface
Each LBH-SDI-EAD-T unit can be used for RS-232 and IR
interface.
RS-232/IR Dataata
The LBH-SDI-EAD-T transmits two channels of data signals.
Followtheproceduresforinstallingdata terminal devices.
1. Labelandconnectoneserialdatacable totheuser’sRS-232
orIRdevice.
2. Connect the other end of this cable to the front panel data
terminal block connector on the LBH-SDI-EAD-T (see
Figure2-4).
Figure 2-4
RS-232/IR Terminal block pinout
Figure 2-5
IR Cable pinout

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 15
2.2.1.4 Status LED’s
AdditionalstatusLED’sare providedfortheuser toindicatethe
presence of HDCP video, audio presence and data presence.
These are to assist the user in identifying right from the front
panelwhethera givensignalis presentfortransmission andaid
in the troubleshooting process if a given signal is missing.
2.2.2 CAT-5e/6 Cable Connection
Followtheensuing instructionsoninstallingand connectingthe
CAT-5e/6 links:
1. Ensure the power is off before proceeding with the
CAT-5e/6 cable installation.
2. Itisrecommendedtouse shielded CAT-5e/6 cabling.
3. ConnecttheCAT-5e/6fromone unittotheotherconnecting
the near end LBH-SDI-EAD-T unit’s HDBT port to the far
end of the LBH-HDMI-EAD-R unit’s CAT-5e/6 RX port as
illustrated in Figure 2-6.
HDCP LED: Will be solid LED when video
input has a HDCP. It will blink when video
input does not have HDCP.
Data in and Data out LED:
It will be on when the unit
detects data signal.
SPDIF & L/R detect LED.
It will be on when the unit detect
the audio input signal.
LBH-HDMI-EAD-Rx
Out
L/R
SPDIF
OUT
HDMI
HDCP
LINK
PWR/
DATA
DATA
AUDIO
IR
12543 L/R
SPDIF
In
1
122

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
16
Figure 2-6
CAT-5e/6 Connection
LBH-SDI-EAD-T
LBH-HDMI-EAD-R
LBH-SDI-EAD-T-WP
LBH-HDMI-EAD-R-WP
1.5AMP
+24VDC
LINK
1.5AMP
+24VDC
LINK
+24V
+24V

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 17
2.3 DC Power Connection
Congratulations! You are now ready to power up the LBH-SDI-EAD-T
and set up your network connection. In order to make sure that you
haveaproperinstallation, please observethefollowing:
1. YourAC jack has power.
2. The24VDCpowersupply is working.
3. Yourelectricalsystemhaspropergrounding (this ensures
that your power supply does not suffer from voltage
variations).
4. Power Surge Protection. This is optional, but highly
recommended. AUPSsystemprovidesvoltage regularity
as well as prevents spikes from occurring, thus protecting
yourLBH-SDI-EAD-Tfrom sensitive voltageconditions.
TheLBH-SDI-EADderivespowerfromanexternal 24VDCpowersupply.
This power supply is a wall mounted AC/DC adapter, 100-240 VAC,
50-60 Hz, at 1.0A. This power supply comes standard for the
LBH-SDI-EAD-Tunlessotherwise specified.
Ifyouhaveanyproblemsorconcerns, regarding the installation, make
sure that you have taken the proper steps to ensure a proper power
connection. Otherwise, feel free to contact us for any questions you
mayhave.

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
18
2.4 In-Wall Power/CAT-5e/6 Wiring Instruction
Thein-wallpower/CAT-5e/6installationfor theLBH-SDI-EAD-T-WP(wall
plateversion)mustconformtonational and local electrical codes,e.g.,
ULjunctionboxesshall be usedandDCpowersource shall notexceed
product rated range (+24VDC @ 1.0A). Follow the following steps for
power/CAT-5e/6 installation:
1. As shown in Figure2-7,feedbothCAT-5e/6 and power cables
throughtheopeningof thewallbox,and secure thecableswith
cableclampstoprovidestrainrelief.
2. Terminated CAT-5e/6withRJ45 connectorto bedirectlyplugged
into the RJ45 connector port of the LBH-SDI-EAD-T-WP units
(see Figure 2-6).
3. Before connecting powerwiretothe LBH-SDI-EAD-T-WPunit,
make sure power supply is off. Prepare the Positive (+24V)
and Negative (GND or +24V return), and chassis ground
(CHASSIS to earth ground) tip of the power wire as shown in
Figure2-8tobedirectlypluggedintothe captivescrew+24VDC
connector of the LBH-SDI-EAD-T-WP units (see Figure 2-7).
Make sure the polarity of the connection is correct. Insulate
any exposed wire shields to prevent short circuits.

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 19
Figure 2-7
In-wall CAT-5e/6/power cable installation
Figure 2-8
Power Connection
LBH-DVI-EAD-WP
Unit
Clamp
Power
Wire
CAT-5e/6
Cable
+24V
GND
Wall
Junction Box
Link Port
+24V GND
+_
Captive
Screw
Connector

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video ConvertingTransmitter System
Broadata Technical Support, [phone]
20
Note 1: Duringinstallation,the installer mayneedtoconnect the power
supplyoutputtoan appropriate ListedNECtypecable before it
isroutedbehindawall. Simply routingthepowersupplyoutput
cable behind a wall will most likely not comply with applicable
installation requirements. Unit should only be powered by a
powersourcethat isListed(NEC) Class2or aListedITE Power
Supply marked/rated as LPS or Limited Power Source.
Note2: The installation shall be in accordance with the applicable
provisions of the National Electrical Code ANSI/NFPA 70,
Article 725 and the Canadian Electrical Code, Part 1,
Section 16.
Note 3: Thepowersupply shall notbepermanently fixed tothebuilding
structure or similar structures.
Note4: Thepowersupplyshall not be located withinenvironmentalair
handling spaces or within the wall cavity.
Note5: The power supply is to be located within the same vicinity as
theA/Vprocessing equipment inanordinarylocation, Pollution
Degree 2, secured to the equipment rack within the dedicated
closet, podium or desk.

LBH-SDI-EAD-TUser’sManual
Link BridgeTM HDBT SDI Video Converting Transmitter System
Broadata Technical Support, [email protected] 21
Table 1
LED Indicator
3.0 OPERATION
After the installation procedure is completed, the units are ready for
operation. Tooperatethe LBH-SDI-EAD-Tunits,simplyapplypower as
indicated in the previous sections. The following describes the LED
activity.
LED Indicator Description
PWR/LINK When power is connected, this LED turns RED.
When power and link are on, this LED turns GREEN
It will be a solid BLUE LED when video input has a
HDCP. It will blink when video input does not have
HDCP
GREEN LED will be on when unit detects the audio
input signal
GREEN LED will be on when the unit detects the SPIF
input signal
GREEN LED will be on when the unit detects data signal
HDCP
L/R
SPDIF
DATA