BRUEL & KJAER LAN-XI Notar BZ-7848-A User manual

BR1754–13
Quick Start Guide
LAN-XI Notar™ BZ-7848-A

2
Table of Contents
Installation – Single Module.................................................................................... 3
Connection and Setup............................................................................................ 4
Connecting a LAN-XI Module to a Network...................................................... 4
Connection of LAN-XI Module Directly to PC ................................................... 5
Setup of LAN-XI Notar...................................................................................... 6
LAN-XI Software Updates ...................................................................................... 6
Using LAN-XI Notar................................................................................................ 9
Installing a LAN-XI Notar License......................................................................... 10
Changing Module Front Panels............................................................................ 10
Using Power over Ethernet (PoE) ........................................................................ 11

3
Installation – Single Module
1) If the system includes optional Battery Module for LAN-XI Type 2831-A,
connect it to the right-hand side (looking from the back) of the LAN-XI
module using the included hex wrench and the four captive screws.
Shown: Hex Wrench QX-1315*, 2 mm.
*Included with LAN-XI Module Types 3050, 3052, 3053, 3056, 3160 and 3161
2
3
4
090122/1
3
4
5
5
1
1

4
2) If you are going to use Type 2831-A, connect it to the LAN-XI module using
Single Module Battery Adaptor ZH-0686*as shown.
3) Connect a network cable. Shown: LAN Cable AO-1450†, 2 m Cat 6.
4) If you will not be using power over ethernet, connect a power cable – one
of:
• Mains Adaptor ZG-0426*, 90 – 264 VAC
• Charger for Li-Ion Battery ZG-0469†,90–264VAC
• Car Utility Socket Cable AO-0546, 10 – 32 VDC
• External Battery Cable AO-0548, 10 – 32 VDC
5) Insert a mini-SD card, or a micro-SD card with an adaptor.
Shown: 16 GB Micro-SD Card with Mini-SD Adaptor UL-1018‡.
Note:
If you connect to a LAN-XI 100 kHz module Type 3052 that is not inside a
frame, the enclosed Ferrite Choke LK-0013 must be attached to the LAN cable,
close to the module, to fulfil the CE requirements of “EN/IEC 61000–6–4:
Generic emission standard for industrial environments."
The Ferrite Choke is not necessary when Type 3052 is in a LAN-XI frame, or
when used without a LAN cable as a LAN-XI Notar recorder.
Connection and Setup
Connecting a LAN-XI Module to a Network
Using DHCP
LAN-XI modules are configured to use a DHCP server by default. If the module
has been set to a static IP address via the module’s home page, you must reset
the module to be a DHCP client. To reset the module, press and release the
Control button on the front of the module to display the menu, then scroll down
the menu by pressing the button once for each menu item. Press and hold the
Controlbuttonfor5 secondswhilethecursorison‘LANreset’inthedisplaymenu.
*Included with LAN-XI Module Types 3050, 3052, 3053, 3056, 3160 and 3161
†Included with Battery Module for LAN-XI Type 2831-A
‡Included with LAN-XI Notar BZ-7848-A

5
When the front-end is a DHCP client, simply connect it to the network and
network settings will be supplied by the DHCP server.
Using a Static IP
To assign the module a static IP, first connect the module directly to the
computer or through a DHCP network as explained above. Open the LAN-XI
module’s web page, by typing the IP address from the front of the module into
your web browser, and follow these steps:
1) Click Network.
2) Click Static.
3) Enter an IP address, and, if necessary, a mask and gateway.
4) Click Save changes.
The module now has a static IP.
Connection of LAN-XI Module Directly to PC
This method only works when both the module and the computer are
configured to be DHCP clients. To reconfigure the module to be a DHCP client,
follow the instructions in Connecting a LAN-XI Module to a Network.
To connect a PC directly to a LAN-XI module:
1) Start up your PC and the LAN-XI module without connecting them. Wait for
them both to detect that there is no LAN connection as indicated (a) in the

6
PC tray if the notification icon is switched on, and (b) on the module, when
it displays the IP address 0.0.0.0.
2) Connect the PC and LAN-XI module with a standard LAN cable and wait
until an IP address is obtained. The message that the PC may give about
having limited or no connectivity (c) is an indication that the connection is
working.
An IP address in the default range 169.254.*.*, will be assigned to the
module and shown on its display (d).
3) Open a browser on your PC, PDA or SmartPhone and enter the IP address
(e) to open the front-end’s web page.
Setup of LAN-XI Notar
If your LAN-XI Notar was ordered at the same time as the LAN-XI module, then
the LAN-XI Notar firmware and license will have been installed and tested at
Brüel & Kjær. Go to “Using LAN-XI Notar” to continue.
If your LAN-XI Notar was ordered separately, go to “Installing a LAN-XI Notar
License” to continue.
LAN-XI Software Updates
Brüel & Kjær continually updates LAN-XI firmware. There are three ways to
download a firmware update to your LAN-XI Module: by connecting to Front-
end Setup following the directions in the next section, by going to
www.bksv.com and selecting Support,Downloads (skip to step 3 below) or
through the front-end’s home page by following the directions below:
e

7
1) Connect to the module’s home page by typing the IP address from the front
of the module into your web browser.
2) Click Downloads.
3) Select LAN-XI under Step 1 and LAN-XI Software Updates under Step 2.
4) Right-click on the latest Firmware.lxi and download the binary firmware to
any location on your PC.
5) On your module’s home page, click Firmware.

8
6) Click Browse... and navigate to the file.
7) Click Start update.

9
Using LAN-XI Notar
1) Open the front-end’s
web page from any
browser and click
Recorder in the menu.
2) Click Create new>> in
the recordings window.
3) Name the recording, set
up the parameters and
click Next>>.
4) Start recording either by
clicking Start on the
module’s web page (4b)
or by pressing the
Control button below
the module’s display
(4a).
5) Click Finish.
Status Control
090124/1
1
2
3
4a
4b
5

10
Installing a LAN-XI Notar License
Changing Module Front Panels
To change a module’s front panel:
1) Remove the hex wrench from the side of the module (see 1 on page 3).
2) Unscrew the screw inside the hole at the bottom of the front panel.
3) Pull out the panel, bottom first.
4) Insert the new panel.
5) Tighten the screw.
Installing a License
1) Insert the CD-ROM or connect the USB Memory
Stick that came as part of the BZ-7848-A package.
2) Open the license.txt file in any word processing or
text editor and copy the text string.
3) Connect to the module’s home page and click
Recorder in the menu to enter the recorder.
4) Paste the license string in the License Key field and
click Submit.