Bryant FAN COIL UNITS FF1DNA User manual

Form No. PDS FF1D.18.2
FAN COIL UNITS
FF1DNA,
FF1DNE
Sizes 018, 024, 030
FEATURES
The FF1DNA and FF1DNE Fan Coil units are designed as
upflow indoor air handlers for split-system heat pumps and air
conditioners. They are available with factory- or field-installed
electric heaters both of which include the disconnect. A field-
installed cooling control with disconnect is also available. A TDR
(Time Delay Relay) is included with either the electric heat or
the cooling control packages. The FF1DNE models are avail-
able with a factory installed TXV.
This fan coil may be installed free standing, wall hung or flush
mounted in the wall. The 22-in. wide cabinet size in all models
allows units to fit between standard stud spacings. No return air
ductwork is required if the application provides for return air in
the front of the cabinet through either a louvered closet door or
an optional accessory decorative grille panel.
The cabinet exterior is made of pre-painted galvanized sheet
metal. The cabinet is fully insulated to meet applications in con-
ditioned space. Additional insulation is required if the unit is
installed in an unconditioned space. Unit is supplied with
replaceable filter.
Multispeed direct-drive PSC blower motors have been selected
to provide the proper air handling for both heating and cooling.
Motors are suspended at 3 points on rubber grommets for qui-
eter operation.
All refrigerant lines, electrical power, and thermostat wiring
enter from the top of the cabinet. Sweat-type refrigerant con-
nections on both liquid and suction lines make for swift, low-cost
installation. All service access to the unit is conveniently located
in the front.
The CHECK-FLO-RATER
®
piston ensures efficient and
dependable refrigerant metering, and eliminates potential ser-
vice requirements of other metering devices. The CHECK-FLO-
RATER
®
is located inside the unit, easily accessible for piston
maintenance or changeout.
In addition, units can be factory ordered with a hard shut-off
thermostatic expansion valve (TXV) metering device for perfor-
mance improvement.
The drain pan is constructed of high-impact, sound-deadening,
corrosion-proof polyester resin. Primary and secondary drain
connections exit from the bottom or either side of the cabinet.
FF1D

—2—
MODEL NUMBER NOMENCLATURE
CERTIFICATION APPLIES ONLY WHEN THE
COMPLETE SYSTEM IS LISTED WITH ARI.
PHYSICAL DATA
NOTE: Rough-in dimensions are 38-1/4 x 22-1/4 inches.
CLEARANCES
A minimum clearance of 21 in. is required in front of the access panels for servicing. Please note that this clearance is recommended
for servicing only. Installation clearances from combustible materials are: 0 in. from cabinet and supply-air duct (plenum included).
Leave adequate room for the condensate pan and refrigerant line connection.
NOTE: 22-3/4 to 24-in. on-center between-studs and 38-1/8 to 36-3/4-in. top-to-bottom inside-studs spacing.
F F 1 D N A 018 075
Electric Heater (kw)
000
005
075
011
Nominal Capacity (Btu)
018—18,000
024—24,000
030—30,000
A—Standard
E—TXV
N—208/230-1-60
D—Major Series
1—Upflow
F—Through-the-Wall
F—Fan Coil
MODEL FF1DNA/FF1DNE 018 024 030
Fan
Rpm (2-Speed)
Motor HP (PSC)
Wheel (In.)
810/750
1/12
10 x 6
980/780
1/5
10 x 6
1110/950
1/3
10 x 6
Filter (Permanent) (In.) 16 x 20 16 x 20 16 x 20
Connections (Sweat)
Suction OD
Liquid OD
Condensate (FPT)
(In.)
(In.)
(In.)
5/8
3/8
3/4
3/4
3/8
3/4
3/4
3/8
3/4
Operating Weight
(With Electric Heat) (Lb) 76 79 82
M
A
N
U
F
A
C
T
U
R
E
R
C
E
R
T
I
F
I
E
D
T
O
A
R
I
A
S
C
O
M
P
L
Y
I
N
G
W
I
T
H
A
R
I
S
T
A
N
D
A
R
D
2
4
0
U
N
I
T
A
R
Y
H
E
A
T
P
U
M
P
E
Q
U
I
P
M
E
N
T
®
M
A
N
U
F
A
C
T
U
R
E
R
C
E
R
T
I
F
I
E
D
T
O
A
R
I
A
S
C
O
M
P
L
Y
I
N
G
W
I
T
H
A
R
I
S
T
A
N
D
A
R
D
2
1
0
U
N
I
T
A
R
Y
A
I
R
C
O
N
D
I
T
I
O
N
I
N
G
E
Q
U
I
P
M
E
N
T
•CERTIFICATION •LISTING
•TESTING •INSPECTION
®

—3—
DIMENSIONS —FF1DNA, FF1DNE
A98336
OUTLET AIR
INLET AIR
SUCTION
TUBE
COIL
1 1⁄8″ DIA.
KNOCKOUT
SIDE VIEW FRONT VIEW
TOP VIEW
BOTTOM VIEW
PRIMARY DRAIN
PATCH PLATE
FAN COIL BASE
BLOWER, CONTROL AND
ELECTRIC HEATER
ACCESS PANEL
LIQUID TUBE
FILTER MEDIA
SECONDARY DRAIN
LOW VOLTAGE ENTRY
( 7⁄8″DIA. HOLE)
POWER ENTRY
1 3⁄8″DIA. KNOCKOUT
7⁄8″ DIA. HOLE
22 1⁄8″
11 3⁄16″
3 1⁄4″
24 1⁄16″
5 11⁄16″5″
10 1⁄16″
1 5⁄8″
5 3⁄16″1 9⁄16″
2 13⁄16″
2 7⁄16″
2 3⁄8″
7⁄8″
3⁄4″
15 3⁄16″
8 1⁄4″4 3⁄16″
3⁄4″
11 1⁄16″
9 7⁄16″
13⁄16″
11 1⁄16″
5″
38 1⁄16″
REFRIGERANT
LINES ENTRY
SUCTION, 018, 024, 030 - 3⁄4″I.D. SWEAT
LIQUID, 3⁄8″I.D. SWEAT
CONDENSATE, 3⁄4″ NPT
UNIT CONNECTION SIZES
NOTE:
1. SERIES DESIGNATION IS
THE 14TH POSITION
OF UNIT MODEL NUMBER.
2 3⁄4″

—4—
SPECIFICATIONS
See notes on page 5.
UNITS WITHOUT ELECTRIC HEATERS OR CONTROLS
UNIT SIZE 0180 0240 0300
RATINGS & PERFORMANCES
Nominal Capacity (Btuh)* 18,000 24,000 30,000
Nominal Airflow (CFM) 650 870 1080
ELECTRICAL
Unit Volts-Phase (60 Hz) 208/230—1 208/230—1 208/230—1
Operating Voltage Range 187—253 187—253 187—253
Internal Circuit Protection None
Minimum Ampacity for Wire Sizing —
Minimum Wire Size†14
Maximum Fuse Size (Amps or Ckt Bkr) 15
Control Transformer 24V (Va) —
INDOOR COIL
Rows & Fins Per In. 2 & 14 3 & 14
Height x Width (In.) 18 x 17.8 22 x 17.8
Face Area (Sq Ft) 2.23 2.72
R-22 Refrigerant Metering Device–FF1DNA Check-Flo-Rater
R-22 Refrigerant Metering Device–FF1DNE TXV
Piston Number‡55 63 70
Condensate Drain Connection (Pri-Sec) 3/4 FPT
INDOOR BLOWER & MOTOR
Wheel Diameter x Width (In.) 10 x 6
Filter Size—Cleanable (In.) 16 x 20 x 1
Blower Motor HP 1/12 1/5 1/3
Blower Motor Speeds & Type 2 & PSC 2 & PSC 2 & PSC
Full Load Amps 0.7 1.5 2.0
OPTIONAL EQUIPMENT
Cooling Control Relay-Transformer Package
(with TDR) KFDCC0101DCC
Louvered Wall Panel with Frame (6 Pack) KFBLG0106LGL
Electric Heat Package See ‘‘Optional Field-Installed Electric Heat Packages’’ Table
UNITS WITH FACTORY-INSTALLED ELECTRIC HEATERS OR CONTROLS
SIZES 018005 018075 018011††
RATINGS & PERFORMANCES
Nominal Capacity (Btuh)* 18,000 18,000 18,000
Nominal Airflow (CFM) 650 650 650
Electric Heating Output (kw @240v) 5.0 7.5 11.0
Electric Heating Capacity (MBH @208/230v) 13.5/16.3 19.9/24.2 28.9/35.1
ELECTRICAL
Unit Volts-Phase (60 Hz) 208/230—1 208/230—1 208/230—1
Operating Voltage Range 187—253 187—253 187—253
Internal Circuit Protection None
Full Load Amps 18.1/20.0 27.1/30.0 39.8/44.0
Minimum Ampacity for Wire Sizing 23.5/25.9 34.8/38.4 50.6/55.9
Minimum Wire Size†10/10 8/8 6/6
Maximum Wire Length (Ft)†112/112 118/118 125/125
Maximum Fuse Size (Amps or Ckt Bkr) 25/30 35/40 60/60
Control Transformer 24V (VA) 40
INDOOR COIL
Rows & Fins Per In. 2 & 14
Height x Width (In.) 18 x 17.8
Face Area (Sq Ft) 2.23
R-22 Refrigerant Metering Device–FF1DNA Check-Flo-Rater
R-22 Refrigerant Metering Device–FF1DNE TXV
Piston Number‡55
Condensate Drain Connection (Pri-Sec) 3/4 FPT
INDOOR BLOWER & MOTOR
Wheel Diameter x Width (In.) 10 x 6
Filter Size—Cleanable (In.) 16 x 20 x 1
Blower Motor HP 1/12
Blower Motor Speeds & Type 2 (PSC)
Full Load Amps 0.7
OPTIONAL EQUIPMENT
Louvered Wall Panel with Frame (6 Pack) KFBLG0106LGL
Electric Heat Package See ‘‘Optional Field-Installed Electric Heat Packages’’ Table

—5—
SPECIFICATIONS Continued
* Rated in accordance with U.S. Government DOE test procedures and/or ARI Standard 210/240-94.
†Use copper wire only. Use 75°C in this application.When using non-metallic (NM) sheathed cable, wire size required should be based on that of 60°C con-
ductors, instead of wire sizes shown in table above per NEC 1996 Article 336-30. Length shown is as measured 1 way along wire path between unit and
service panel for voltage drop not to exceed 2%.
‡Check outdoor unit for required piston size.
†† 018 Size with 11-kw heater not approved for use with heat pumps.
UNITS WITH FACTORY-INSTALLED ELECTRIC HEATERS OR CONTROLS
UNIT SIZE 024005 024075 024011 030005 030075 030011
RATINGS & PERFORMANCES
Nominal Capacity (Btuh)* 24,000 24,000 24,000 30,000 30,000 30,000
Nominal Airflow (CFM) 870 1080
Electric Heating Output (kw @240v) 5.0 7.5 11.0 5.0 7.5 11.0
Electric Heating Capacity (MBH @208/230v) 14.0/16.9 20.4/24.7 29.4/35.7 14.3/17.2 20.7/25.0 29.7/36.0
ELECTRICAL
Unit Volts-Phase (60 Hz) 208/230—1 208/230—1 208/230—1 208/230—1 208/230—1 208/230—1
Operating Voltage Range 187—253 187—253 187—253 187—253 187—253 187—253
Internal Circuit Protection None
Full Load Amps 18.1/20.0 27.1/30.0 39.8/44.0 18.1/20.0 27.1/30.0 39.8/44.0
Minimum Ampacity for Wire Sizing 24.5/26.9 35.8/39.4 51.6/56.9 25.2/27.5 36.4/40.0 52.3/57.5
Minimum Wire Size†10/10 8/8 6/6 10/10 8/8 6/6
Maximum Wire Length (Ft)†112/112 117/117 122/122 112/112 117/117 125/125
Maximum Fuse Size (Amps or Ckt Bkr) 25/30 40/40 60/60 30/30 40/40 60/60
Control Transformer 24V (Va) 40
INDOOR COIL
Rows & Fins Per In. 3 & 14
Height x Width (In.) 18 x 17.8 22 x 17.8
Face Area (Sq Ft) 2.23 2.73
R-22 Refrigerant Metering Device-FF1DNA Check-Flo-Rater
R-22 Refrigerant Metering Device-FF1DNE TXV
Piston Number‡63 70
Condensate Drain Connection (Pri-Sec) 3/4 FPT
INDOOR BLOWER & MOTOR
Wheel Diameter x Width (In.) 10 x 6
Filter Size—Cleanable (In.) 16 x 20 x 1
Blower Motor HP 1/5 1/3
Blower Motor Speeds & Type 2 (PSC)
Full Load Amps 1.5 2.0
OPTIONAL EQUIPMENT (P/N’s)
Louvered Wall Panel with Frame (6 Pack) KFBLG0106LGL
Electric Heat Package See ‘‘Optional Field-Installed Electric Heat Packages’’ Table

—6—
COOLING CAPACITIES (MBtuh)
* Saturated suction leaving evaporator coil.
COIL REFRIGERANT TEMPERATURE* (°F)
UNIT
SIZE
EVAPORATOR
AIR
CFM and
BF
35 40 45 50 55
Evap Air—Entering Wet-Bulb Temp (°F)
72 67 62 72 67 62 72 67 62 72 67 62 72 67 62
018
400 27 23 19 25 20 16 22 17 13 19 14 10 15 10 8
0.08 13 14 15 12 13 13 10 11 12 9 10 10 8 8 8
500 30 25 21 28 22 18 24 19 15 21 15 12 16 11 10
0.10 14 16 17 13 14 16 12 13 14 10 11 12 9 10 10
600 33 27 22 30 24 19 26 21 16 23 17 13 18 12 11
0.13 15 17 19 14 16 18 13 14 16 11 13 13 10 11 11
650 34 28 23 31 25 20 27 21 17 23 17 14 18 13 12
0.14 16 18 20 14 17 18 13 15 16 12 13 14 10 11 12
024
600 38 32 26 35 29 22 31 24 18 26 19 14 21 13 12
0.05 18 20 21 16 18 19 15 16 17 13 14 14 11 11 12
700 41 34 28 38 30 24 33 26 20 28 20 16 22 15 13
0.06 19 21 23 18 19 21 16 18 19 14 15 16 12 13 13
875 46 38 31 41 34 27 37 29 22 31 23 19 25 17 16
0.08 21 24 27 20 22 24 18 20 22 16 18 19 14 15 16
030
750 46 38 31 41 33 26 36 28 21 30 22 17 24 16 14
0.04 21 23 25 19 21 22 17 19 20 15 16 17 12 13 14
900 50 42 34 46 37 29 40 31 23 33 25 19 26 18 16
0.06 23 26 28 21 23 25 19 21 22 17 18 19 14 15 16
1075 54 45 37 49 40 32 43 34 26 37 27 22 29 19 18
0.07 25 28 31 23 26 28 21 23 25 18 21 22 16 17 18
Sensible Heat Capacity (1000 Btuh)
Gross Cooling Capacity (1000 Btuh)
BF —Bypass Factor
NOTES:
1. Net capacities shown include a deduction for evaporator fan motor heat.
2. Contact manufacturer for cooling capacities at conditions other than
shown in table.
3. Formulas:
Leaving db = entering db —
Leaving wb = wb corresponding to enthalpy of air leaving coil (h
lwb
)
h
lwb
= h
ewb
—
where h
ewb
= enthalpy of air entering coil.
4. Direct interpolation is permissible. Do not extrapolate.
5. SHC is based on 80°F db temperature of air entering coil. Below 80°F
subtract (corr factor x CFM) from SHC.
Above 80°F db, add (corr factor x CFM) to SHC.
SHC CORRECTION FACTOR
sensible heat cap.
1.09 x CFM
total capacity (Btuh)
4.5 x CFM
BYPASS
FACTOR
ENTERING AIR DRY-BULB TEMP (°F)
79 78 77 76 75 Under 75
81 82 83 84 85 Over 85
Correction Factor
0.10
0.20
0.30
0.98
0.87
0.76
1.96
1.74
1.53
2.94
2.62
2.29
3.92
3.49
3.05
4.91
4.36
3.82
Use formula
shown below
Interpolation is permissible.
Correction Factor = 1.09 x (1 –BF) x (db –80)
OPTIONAL FIELD-INSTALLED ELECTRIC HEAT PACKAGES FOR FF1DNA AND FF1DNE
* Heater capacities shown here are for the largest size fan coil unit, and they do include blower motor heat.
HEATER PART NUMBER
WITH TDR
SIZE
USED
WITH
NOMINAL
KW @
240V
HEATER
VOLTS—PHASE
(60 Hz)
HEATER
CAPACITY
(MBH)*
APPROX
SHIP.
WEIGHT
(lbs)208V 230V
KFDEH0801D05 All 5 208/230—1 14.3 17.2 7
KFDEH0901D75 All 7.5 208/230—1 20.7 25.0 7
KFDEH1001D11 All 11 208/230—1 29.7 36.0 7

—7—
AIR DELIVERY (CFM) AT INDICATED EXTERNAL
STATIC PRESSURE AND VOLTAGE
NOTE: Data reflects a dry coil, filter, and 11-kw electric heater installed.
AIR DELIVERY PERFORMANCE CORRECTION
COMPONENT PRESSURE DROP (IN. WC) AT INDICATED AIRFLOW
Subtract the above pressure drop corrections from unit airflow data when that component or condition is used.The remaining external static pressure will be
available for the duct system.
ESTIMATED SOUND POWER LEVEL (dBA)
* Estimated sound power levels have been derived using the method described in the 1987 ASHRAE HVAC Systems & Applications Handbook,
Chapter 52, p. 52.7.
OTHER ACCESSORIES
* 6 pack
EXTERNAL STATIC PRESSURE—IN. WC
UNIT
SIZE
BLOWER MOTOR
SPEED
0.1 0.2 0.3 0.4 0.5
208V 230V 208V 230V 208V 230V 208V 230V 208V 230V
018 High 610 720 580 665 540 610 475 540 380 415
Low 480 580 450 545 415 500 375 430 320 340
024 High 895 985 860 955 825 915 785 865 730 805
Low 650 740 620 710 585 680 550 640 510 600
030 High 1160 1190 1105 1135 1050 1080 990 1020 935 960
Low 885 1025 870 985 835 940 810 890 770 840
AIR DELIVERY (CFM) 400 500 600 700 800 900 1000 1100
Electric
Heaters
1-Element
5 kw 0.007 0.010 0.015 0.025 0.035 0.055 0.070 0.080
2-Element
7.5 & 11 kw 0.010 0.012 0.018 0.028 0.050 0.075 0.100 0.130
Dry-to-
Wet
Coil
018 —0.019 0.029 0.036 0.043 ———
024 ——0.030 0.039 0.051 0.062 0.076 —
030 ————0.058 0.070 0.082 0.091
UNIT
SIZE
CONDITIONS OCTAVE BAND CENTER FREQUENCY*
CFM
Ext Static
Pressure 63 125 250 500 1000 2000 4000
FF1-018 600 0.25 64.7 60.7 56.7 53.7 51.7 49.7 45.7
FF1-024 800 0.25 66.0 62.0 58.0 55.0 53.0 51.0 47.0
FF1-030 1000 0.25 67.0 63.0 59.0 56.0 54.0 52.0 48.0
KIT NUMBER DESCRIPTION USED ON SIZES
KFDCC0101DCC Cooling Control Package All
KFBLG0106LGL* Louvered Wall Panel with Frame All

—8—
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE
UNIT MUST BE INSTALLED IN ACCORDANCE
WITH INSTALLATION INSTRUCTIONS
Cancels: PDS FF1D.18.1
Form PDS FF1D.18.2
© 2003 Bryant Heating & Cooling Systems, 7310 W. Morris St. Indpls, IN 46231 PRINTED IN U.S.A. Catalog No. 12FF-1D1 1-03
SERVICE TRAINING
Packaged Service Training programs are an excellent way to increase your
knowledge of the equipment discussed in this manual, including:
•Unit Familiarization •Maintenance
•Installation Overview •Operating Sequence
A large selection of product, theory, and skills programs is available, using popular
video-based formats and materials. All include video and/or slides, plus companion
book.
Classroom Service Training plus "hands-on" the products in our labs can mean
increased confidence that really pays dividends in faster troubleshooting, fewer
callbacks. Course descriptions and schedules are in our catalog.
CALL FOR FREE CATALOG 1-800-644-5544
[ ] Packaged Service Training [ ] Classroom Service Training
A94328