Buckingham BuckWheel 487 User manual

Buckingham Mfg. Co., Inc.
INSTRUCTIONS AND WARNINGS
BuckWheel
(MODEL NO. 487)
The BuckWheel (model 487) is intended to be used in conjunction with the Wood Pole Fall Protection Devices,
(models 483 & 484). Although intended for use on models manufactured without the Cleat and Serrated Rotosnap
depicted by our 2010 design, it can be used on any BuckSqueeze design manufactured to date. With proper
installation and operation the BuckWheel will prevent models 483 & 484 from slipping on iced poles. (See 480 Series
Instructions / Warnings). To use the Wood Pole Fall Protection Device (WPFPD) with the addition of the BuckWheel,
grasp the Paddle and Carabiner Connector and slide the Outer Strap up the pole to its desired location. Keep the
BuckWheel as flat to the pole as possible. With the top of the Outer Strap angled slightly away from the pole and
downward force applied, the BuckWheel will penetrate the pole, preventing the Outer Strap from slipping. To aid in
descending the pole when using the BuckWheel, lean slightly into the pole to create slack, thrust the outer strap away
from your body so that the BuckWheel unit does not make contact with the pole and let the outer strap drop down the
pole to its desired location (waist level or above). Never let the BuckSqueeze fall below your waist.
BUCKWHEEL PARTS DESCRIPTION:
1. BACK PLATE
2. TWO SCREWS (10-24 x ½”)
3. BODY / WHEEL ASSEMBLY
4. SPRING TENSIONER
Also included – One 1/8” hex head wrench
BUCKWHEEL ASSEMBLED
(Shown without strap for clarity)
BuckWheel Assembly
WARNINGS Proper use and assembly are critical to the performance of the BuckWheel.
Read carefully, understand and heed these instructions and warnings before using this equipment.
Also read carefully, understand and heed the 480 Series instructions and warnings before using this
equipment. Failure to do so could result in your serious injury or death.
This equipment is intended for use by properly trained professionals only.
The BuckWheel should be inspected for damage and proper operation before each use.
If the BuckWheel is subjected to impact loading it should be inspected by properly trained
personnel and replaced if deemed necessary.
BUCKINGHAM MFG. INC.
1-800-937-2825
E-mail – sales @buckinghammfg.com
Web site – www.buckinghammfg.com
487Inst-Warn.doc (Rev. 02/08/11) P/N 230217 Page 1 of 3
Back Plate
10-24 x 1/2”
Screws
Bod
y
/ Wheel Assembl
y
S
p
rin
g
Tensione
r

INSTRUCTIONS
To Install the BuckWheel to the Outer Strap of the WPFPD:
A. Remove the two screws from the BuckWheel assembly.
B. Remove the Back Plate to expose the strap slot.
C. Mount the Body / Wheel Assembly to the center of the Outer Strap by placing the Outer Strap in the top
of the strap slot of the Body / Wheel Assembly then press the strap into the bottom of the slot (Fig. 1a).
Caution: Make sure that the Body / Wheel Assembly is mounted so that the wheel will be against
the pole and that the end of the assembly with the brass rollers is towards the ground (Fig. 1b).
D. Slide the Back Plate and the Body / Wheel Assembly together ensuring that the tapered pockets of the
Back Plate properly engage with the corresponding tabs of the Body / Wheel Assembly then align the holes
(Fig 2a).
E. Insert the two screws and securely tighten using the supplied hex head wrench (Fig 2b).
487Inst-Warn.doc (Rev. 02/08/11) P/N 230217 Page 2 of 3
Fig. 1a
Towards
Ground
Fig. 1b
Against
Pole
NOTE: When re-adjusting the WPFPD hardware locators to the 3
and 9 o’clock positions it will be necessary to adjust the
BuckWheel so that it is always at the rear of the pole
(12 o’clock position).
Fig. 2a Fig. 2b

INSPECTION
Prior to each use, carefully inspect this equipment for indications of wear or deterioration. The inspection should
include, but not be limited to the following:
unit is free from cracks, excessive wear or corrosion.
unit is properly assembled and all screws are in place, fully seated and properly tightened.
the slot and the wheel of the BuckWheel Assembly are free of dirt, debris and ice build up (excessive
build up may cause improper operation of this unit).
wheel and rollers rotate freely without any binding.
If any evidence of wear / deterioration as outlined or any unusual conditions not outlined above be observed, or you
have reasonable doubt about a particular condition, immediately remove the equipment from service and notify your
Supervisor, Safety Director or contact Buckingham Mfg. (1-800-937-2825) for clarification.
CLEANING
The BuckWheel may be cleaned by using a cotton swab, limited air pressure or dipping it into a container of water to
remove fine particles and any foreign matter which may enter around wheel pin and prevent proper function. The
exterior should be dried with a clean cloth. The inside should be air-dried and re-lubricated as needed.
MAINTAINENCE
Lubricate as often as required to maintain smooth operation (no binding) with a lightweight lubricant such as WD-40®.
Do not excessively lubricate, wipe away any excess lubricant with a clean dry cloth.
STORAGE
Proper cleaning, maintenance and storage of your equipment will prolong its useful life and contribute toward its
performance. Your equipment should be stored and transported so that it does not come into contact with debris,
moisture, or chemical agents.
BUCKINGHAM MFG. INC.
1-800-937-2825
E-mail – sales @buckinghammfg.com
Web site – www.buckinghammfg.com
487Inst-Warn.doc (Rev. 02/08/11) P/N 230217 Page 3 of 3