Buffalo CP793 User manual

Model • Modèle • Modell • Modello • Modelo • Malli:
CP793
Induction
Fryer
Instruction manual
CP793_UK_A5_v1_170621.indb 1 2017/6/21 09:46

2
UK
Safety Tips
• Position on a flat, stable surface.
• A service agent/qualified technician should carry out
installation and any repairs if required. Do not remove any
components on this product.
• Consult Local and National Standards to comply with the
following:
- Health and Safety at Work Legislation
- BS EN Codes of Practice
- Fire Precautions
- IEE Wiring Regulations
- Building Regulations
• Caution! Hot surface!
• DO NOT immerse the appliance in water.
• DO NOT clean with jet/pressure washers.
• DO NOT move or carry the appliance when it is switched on.
• DO NOT leave the appliance unattended during operation.
• Caution! Never switch on the deep fryer without oil inside.
• ALWAYS ensure oil levels are within the ‘MIN’ and ‘MAX’
levels. Failure to do so could result in fire.
• ALWAYS use a suitable cooking oil.
• ALWAYS remove excess moisture/water from food before
frying to avoid excess foaming and spitting of the oil.
• Change oil regularly. The flashpoint of oil (the point at which it
ignites) gradually reduces the more it is used.
• In case of fire, never use water to extinguish it. Never
pour water onto hot oil or fat. Use the lid to cover the
fire instead.
• During and after cooking, the unit is still hot. Never touch the
surface and switch on the tap to avoid scalding.
• non-ionizing electromagnetic radiation.
CP793_UK_A5_v1_170621.indb 2 2017/6/21 09:46

3
UK
• People with a pacemaker fitted should not use the appliance
and keep a minimum of 60cm from the appliance during
operation.
• Suitable for indoor use only.
• Always switch off and disconnect the power supply to the
appliance when not in use.
• This appliance must only be used in accordance with these
instructions and by persons competent to do so.
• Keep all packaging away from children. Dispose of the
packaging in accordance to the regulations of local authorities.
• If the power cord is damaged, it must be replaced by an
BUFFALO agent or a recommended qualified technician in
order to avoid a hazard.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience or knowledge, unless they have been
given supervision or instruction concerning the use of the
appliance by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance.
• Buffalo recommend that this appliance is PAT tested
on an annual basis to ensure the product remains safe.
Introduction
Please take a few moments to carefully read through this manual. Correct maintenance and operation of
this machine will provide the best possible performance from your BUFFALO product.
Pack Contents
The following is included:
• BUFFALO induction fryer - 8Ltrs
• Lid
• Frying basket
• Batter plate
• Instruction manual
BUFFALO prides itself on quality and service, ensuring that at the time of packaging the contents are
supplied fully functional and free of damage.
Should you find any damage as a result of transit, please contact your BUFFALO dealer immediately.
CP793_UK_A5_v1_170621.indb 3 2017/6/21 09:46

4
UK
Installation
1. Place the unit on a heat-resistant surface. Avoid placing it on or close to easy flammable materials.
Maintain a distance of 20cm (7 inches) between the appliance and walls or other objects for
ventilation.
2. Keep the unit away from splashing water and countertop’s edge.
Note: Before using for the first time, clean the lid, basket, batter plate and the
oil tank with warm soapy water. Let dry completely.
Operation
Control panel Frying basket
Lid
Batter plate
Drain tap
Reset
button
Removable
air filter
Oil tank
1. Place the batter plate into the oil tank.
2. Pour cooking oil into the oil tank between the
MIN and MAX markings.
Note: Before filling oil, ensure the
drain tap is at the OFF position.
Tap: OFF position
CP793_UK_A5_v1_170621.indb 4 2017/6/21 09:46

5
UK
Cooking
KEEP WARM
indicator light
HEATING
indicator light
Thermostat POWER switch
with indicator light
1. Connect the appliance to the mains power supply.
2. Set the POWER switch to I(ON position). The power indicator light illuminates.
3. Set the thermostat to the desired temperature. The HEATING indicator light (red) turns On. The
appliance begins to heat the oil.
Note: 170°C to 180°C is suitable for general cooking.
4. When the set temperature is reached, the HEATING indicator light (red) turns Off. Meanwhile the
KEEP WARM indicator light (green) goes on.
5. Lower the basket with food into the oil.
6. Remove the basket from the oil once the food is cooked. Shake gently above the oil tank to remove
any excess oil.
WARNING: The food and oil are very hot! Take care when removing the basket
as oil may drip.
7. After use, set the POWER switch to O(OFF position) and disconnect the appliance from the mains.
Self-protection functions
Function Descriptions
Dryheat protection Each time the appliance starts, it performs the self-checking for 20 seconds.
If no oil is detected in the oil tank, the HEATING indicator light will flash 2
seconds repeatedly. Meanwhile a buzzer alarm is on to alert the user to fill oil.
Oil overheat protection This appliance is fitted with a Thermal Cut-Out safety feature. Should the
temperature exceed safe levels appliance will automatically stop working.
To reset the appliance:
1. Allow the appliance with oil to cool.
2. Press the reset button at the back of the appliance.
Energy saving If the appliance is switched on without being used for 3 hours, it will switch
off automatically.
CP793_UK_A5_v1_170621.indb 5 2017/6/21 09:46

6
UK
Cleaning, Care & Maintenance
• Always turn off and disconnect the appliance from the power supply before
cleaning.
• Always allow the appliance and oil to cool before cleaning.
• Check the temperature with a suitable probe thermometer; 40ºC is the MAXIMUM temperature at
which oil should be removed.
• For best performance, BUFFALO recommend that the appliance is cleaned after each day of operation.
• Pull the air filter out of its slot on the bottom of the appliance. Clean with a vacuum cleaner.
Note: Failure to clean the appliance regularly may result in premature activation
of the thermal cut-out switch.
Empty and clean the oil tank
• When the oil has cooled sufficiently, lift the tap lever and rotate anti-clockwise to the ON position. Let
the drained oil flow into a container.
Tap: ON positionTap: OFF position
• If the oil is to be reused then filtering it before refilling will extend the oil’s cooking life.
• Use a suitable detergent to clean the oil tank.
• Let it dry well, ensuring no moisture enters the inside of the appliance.
Cleaning all removable parts
• Use warm, soapy water and a soft brush to clean the lid, basket and batter plate.
• Dry thoroughly.
• A BUFFALO dealer or qualified technician should carry out repairs if required.
Troubleshooting
Error indications Description Probable Cause Solution
HEATING
indicator light
flashes once
continuously
IGBT on the PCB is
overheated. Buzzer
alarms.
Check ventilation
slots for dirt and
grease. Make sure
there is enough
space around the
appliance.
1. Switch the unit off and let it cool.
2. Check the filter and clean if
necessary.
3. Re-start the unit.
Note: If it occurs frequently, call
BUFFALO agent or qualified technician
CP793_UK_A5_v1_170621.indb 6 2017/6/21 09:46

7
UK
Troubleshooting
Error indications Description Probable Cause Solution
HEATING
indicator light
flashes twice
continuously
Temperature sensor
under the oil tank
is either shorted-
circuited or open-
circuited. Buzzer
alarms.
Temperature sensor
is defective
1. Unit overheated.
2. Let it cool.
Note: If it occurs frequently, call
BUFFALO agent or qualified technician
HEATING
indicator light
flashes 3 times
continuously
Input voltage
exceeds the allowed
Max/Min rating
Electrical installation
is not in order
Have a qualified electrician check it.
HEATING
indicator light
flashes 4 times
continuously
Temperature sensor
in the oil tank is
either shorted-
circuited or open-
circuited. Buzzer
alarms.
Temperature sensor
is defective
1. Unit overheated.
2. Let it cool.
Note: If it occurs frequently, call
BUFFALO agent or qualified technician
Fault Probable Cause Solution
Appliance not
working
The unit is not switched on Check the unit is plugged in correctly and
switched on
Plug and lead are damaged Call BUFFALO agent or qualified Technician
Fuse in the plug has blown Replace the plug fuse
Power supply Check power supply
Internal wiring fault Call BUFFALO agent or qualified technician
Appliance stops
working suddenly
Overheating protection 1. Allow the appliance to cool sufficiently.
2. Press the reset button.
If the problem persists, Call BUFFALO agent or
qualified technician
Appliance does
not reach set
temperature
Faulty thermostat Call BUFFALO agent or qualified technician
Faulty element Call BUFFALO agent or qualified technician
Build-up of fat on the element Clean the appliance
Appliance heats up
but indicator light
does not come on
Indicator light has expired Call BUFFALO agent or qualified technician
Power indicator
light comes on but
appliance does not
heat up
Faulty thermostat Call BUFFALO agent or qualified technician
Faulty element Call BUFFALO agent or qualified technician
Thermostat set incorrectly Check and re-set the thermostat
Appliance slow to
heat up
Build-up of fat on the element Clean the appliance
CP793_UK_A5_v1_170621.indb 7 2017/6/21 09:46

8
UK
Technical Specifications
Model Voltage Power Current Capacity
(litres) Weight Dimensions w x d x h mm
CP793 220-240V
50/60Hz
3000W 13 A 8 13.5kg 288 x 440 x 415
Electrical Wiring
This appliance is supplied with a 3 pin, moulded, BS1363 plug and lead, with a 13 amp fuse as standard.
The plug is to be connected to a suitable mains socket.
This appliance is wired as follows:
• Live wire (coloured brown) to terminal marked L
• Neutral wire (coloured blue) to terminal marked N
• Earth wire (coloured green/yellow) to terminal marked E
This appliance must be earthed.
If in doubt consult a qualified electrician.
Electrical isolation points must be kept clear of any obstructions. In the event of any emergency
disconnection being required they must be readily accessible.
Compliance
The WEEE logo on this product or its documentation indicates that the product must
not be disposed of as household waste. To help prevent possible harm to human
health and/or the environment, the product must be disposed of in an approved and
environmentally safe recycling process. For further information on how to dispose of
this product correctly, contact the product supplier, or the local authority responsible for
waste disposal in your area.
BUFFALO parts have undergone strict product testing in order to comply with regulatory
standards and specifications set by international, independent, and federal authorities.
BUFFALO products have been approved to carry the following symbol:
All rights reserved. No part of these instructions may be produced or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written permission of BUFFALO.
Every effort is made to ensure all details are correct at the time of going to press, however, BUFFALO reserve the right to
change specifications without notice.
CP793_UK_A5_v1_170621.indb 8 2017/6/21 09:46

UK 0845 146 2887
NL 0800 – 29 1 29
040 – 2628080
FR 0800 - 29 2 29
01 60 34 28 80
DE 0800 – 1860806
IT N/A
ES 901-100 133
PT 901-100 133
CP793_UK_A5_v1_170621.indb 9 2017/6/21 09:46

CP793_UK_A5_v1_170621.indb 10 2017/6/21 09:46

CP793_UK_A5_v1_170621.indb 11 2017/6/21 09:46

CP793_UK_A5_v1_170621
http://www.buffalo-appliances.com/
CP793_UK_A5_v1_170621.indb 12 2017/6/21 09:46