Buffalo AirStation Nfiniti WZR-HP-G300NH User manual

WZR-HP-G300NH Router Settings (For: Pccw, HGC PPPoE User)
LastUpdated23/06/2009 HorningtonKB: http://kb.hornington.com WZR-HP-G300NH PPPoE Settings Page 1
Hardware Setup of WZR-HP-G300NH Router:: 4. Please connect your broadband service with a network cable (or from
DSL modem) to the “INTERNET” port on the ROUTER. Then use
another network cable to connect “LAN1” port on the ROUTER to the
1. Set Router switch to “ON”. Ethernet adapter on your PC. Make sure indicators “INTERNET” and
“LAN1” near lan ports are ON.
2. Power on Buffalo Router, and wait for 2 minutes.
The “Power”, “Security”, “Wireless” and “Router” indicators will be
ON, and “Diag” will be OFF.
3. To reset the router, please insert “RESET” hole by a paper clip for about
10 seconds, and wait for 2 minutes. The “Power”, “Security”, “Wireless”
and “Router” indicators will be ON, and and “Diag” will be OFF.
5. Wait for 1 minute.

W
1
ZR-HP-G300NH Router Settings (For: Pccw, HGC PPPoE User)
Last pdated23/06/2009 HorningtonKB: http://kb.hornington.com WZR-HP-G300NH PPPoE Settings Page 2U
Prepare for Buffalo Router installation (Windows XP)
.Click “Start”
2. Click “Control Panel” or “Settings” -> “Control Panel”
3. Choose “Internet Options” or “Network and Internet Connections” ->
“Internet Options”
4. Click “Connections” tab, choose “Never dial a connection”, then click
“LAN Settings”
5. Under “Local Area Network (LAN) Settings”, please UNCHECK all
check boxes, then click “OK” twice, and go back to Control Panel

W RZ
LastUpdated23/06/2009 HorningtonKB: http://kb.hornington.com WZR-HP-G300NH PPPoE Settings Page 3
-HP-G300NH Router Settings (For: Pccw, HGC PPPoE User)
6. Under Control Panel, please choose “Network Connections” or
“Network and Internet Connections” -> “Networks Connections”,
then right-click “LocalArea Connection”, and choose “Properties”
7. Highlight “Internet Protocol (TCP/IP)”, and then click “Properties”.
Under “Internet Protocol (TCP/IP) Properties”, choose “Obtain an
IP address automatically” and “Obtain DNS server address
automatically”, then click “OK” twice and go back to Network
Connections
8. Wait for 1 minute.

WZR-HP-G300NH Router Settings (For: Pccw, HGC PPPoE User)
LastUpdated23/06/2009 HorningtonKB: http://kb.hornington.com WZR-HP-G300NH PPPoE Settings Page 4
1.
Buffalo Router WZR-HP-G300NH Internet Connection Setup: 3. Router is now detecting Internet Connection.
Launch Web Browser, enter http://192.168.11.1 in address bar and then
press Enter. Then type username as “root”, password leaves as blank
2. Click “Run the Internet Connection Wizard (Easy Setup)”
4. After a few moment, the following page will be displayed and asking
for“Username/Password”. Please input the login username (e.g.
[e-mail] or [email protected]) and password
(twice) of your broadband service now. Then click “Next”

WZR-HP-G300NH Router Settings (For: Pccw, HGC PPPoE User)
LastUpdated23/06/2009 HorningtonKB: http://kb.honington.com WZR-HP-G300NH PPPoE Settings Page 5
7. Return to “Setup” page, click “Internet/LAN”
5. Wait for about 1 minute.
If “Check the Internet connection” process is successful, the following
page will be displayed. Click “Complete” to close the setup page.
6. If the login information is incorrect, the following page will be displayed.
Please confirm login information. Click “Back” button to return previous
page, re-enter login username/password (twice), and then click “Next” to
check internet connection again.
r

W RZ
LastUpdated23/06/2009 HorningtonKB: http://kb.hornington.com WZR-HP-G300NH PPPoE Setti Page 6
-HP-G300NH Router Settings (For: Pccw, HGC PPPoE User)
8. Under “Method of Acquiring IP Address”, choose “Use PPPoE Client”.
Click “Apply”
9. Wait for 2 minutes
10. Click “Wireless Config”
Under page “WPS”, please UNCHECK “enable” option behind “WPS”
Click “Apply” to save settings
ngs

WZR-HP-G300NH Router Settings (For: Pccw, HGC PPPoE User)
LastUpdated23/06/2009 HorningtonKB: http://kb.hornington.com WZR-HP-G300NH PPPoE Settings Page 7
11. Click "Basic (11n/g/b)"
Behind "Wireless Channel", choose a channel used for the router.
Click "Apply".
In general, you are suggested to try channel 11, 6, or 1.
You may use each channel for a few days to test which channel is more
stable in your environment.
Please do not use “Auto Channel”
Wait for 2 minutes.

WZR-HP-G300NH Router Settings (For: Pccw, HGC PPPoE User)
LastUpdated23/06/2009 HorningtonKB: http://kb.hornington.com WZR-HP-G300NH PPPoE Settings Page 8
Click "Apply" again to confirm
.
Wait for about 2 minutes.
12. There is a label on bottom of router printed with “SSID” and “KEY”
SSID represents the default wireless name of router
KEY represents the default wireless encryption key of router
For related topics about WZR-HP-G300NH, please refer to Hornington
Knowledge Base:
http://support.hornington.com/kb/category.php?catID=115
Setting Completed