Buffalo DriveStation HD-HBU2 Series User manual

Package contents:
Main Unit (DriveStation) 1
Power Adapter 1
DriveStation Feet 2
USB Cable 1
DriveNavigator Installation CD 1
Quick Setup Guide 1
The front face of the DriveStation has a protective plastic film covering for
protection from scratching during assembly and shipping. The film can be
removed by peeling it away from any corner of the front face.
Quick Setup Guide
HD-HBU2 DriveStation
www.buffalotech.com v3.0

2
DriveStation Setup
Flip the power switch on the back of DriveStation to the OFF position.
Plug DriveStation’s power cord into a power outlet. Then, connect the
included USB cable into the USB port on the back of DriveStation.
Connect the USB cable into the USB port on the computer or device you
are adding the DriveStation to.

3
Flip the power switch on the back of the DriveStation to the ON position.
In Windows 2000 and XP, the DriveStation will automatically install upon
power-on.
Open ‘My Computer’ and the new drive will be present. By default it will
use the first available drive letter and will be named ‘Local Disk’. The
DriveStation comes pre-formatted so you may begin using it immediately.
The DriveNavigator CD includes several useful utilities for your Windows
System. Please insert the DriveNavigator CD into your CD-ROM Drive to
learn more about them.
DriveStation Setup
Windows 2000 & XP

4
Insert the DriveNavigator CD into your CD-ROM Drive. Shortly thereafter
the DriveNavigator Easy Setup program will launch.
NOTE: If the DriveNavigator program does not launch, it can be launched
by pressing on the ‘Start Menu’ and selecting the ‘Run’ option. Once the
dialog opens, type X:\easysetup.exe (where X is CD-ROM drive letter).
Press the DriveStation Setup Wizard button to being the basic setup
of your DriveStation. Please follow the on screen documentation to
complete the DriveStation Setup for your system. The DriveNavigator CD
includes several useful utilities for your Windows System. Please explore
the Documentation to learn more about them.
DriveStation Setup
Windows 98SE & ME

5
Flip the power switch on the back of the DriveStation to the ON position.
Please refer to the User Manual on the LinkStation’s LinkNavigator CD for
LinkStation USB Disk configuration.
DriveStation Setup
Using DriveStation with LinkStation

6
The following is a list of common issues with the DriveStation. Following
each common issue are possible resolutions.
I see the DriveStation in ‘My Computer’ but I cannot access it.
The drive requires formatting. Try using the Disk Formatter
Utility on the DriveNavigator CD-ROM. Consult the manual for
the Disk Formatter Utility for more help. The manual can also be
found on the DriveNavigator CD-ROM.
I cannot see the DriveStation in ‘My Computer’.
Verify that the POWER light is lit green. If it is not, then ensure
that the power switch is in the ON position.
Try toggling the POWER MODE switch right below the power
switch. The POWER MODE switch toggles whether the device is
powered up via a USB signal or purely based on the power
switch’s position.
If you have installed the Power Save Utility, then verify that the
DriveStation was not put into power saving mode. Consult the
manual for the Power Save Utility for additional help. The manual
can be found on the DriveNavigator CD-ROM.
Verify that the hard drive inside the DriveStation is spinning. This
can be verified by placing your hand on the sides of the case
and feeling for a slight vibration. Also, after the DriveStation has
been powered on for fifteen minutes or more it will begin to get
warm. If neither of the preceeding tests verified that the hard drive
is spinning, then please contact technical support for further
assistance.
If you are experiencing any additional troubles, please contact our technical
support for additional assistance.
Troubleshooting
Troubleshooting

7
Technical Support
Buffalo Technology offers free technical support (24/7 Phone Support in
North America, Email Support in Europe). Please see the back page of
this quick start guide for the contact information. Please also visit the
web site at http://www.buffalotech.com
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Technical Specifications
USB Standards: USB Specification Rev. 2.0
Capacity: 160, 250 GB
Seek Time: Max. 11 milliseconds
Transmission Speed: Max. 480 Mbps
Power Consumption: Max. 25W, Average 17W
Power Supply: AC100V 50/60Hz
Dimensions: 53(W) x 173(H) x 164(D) mm
Weight: 3.15 lb.
Operating Environment: 5 - 35 degree C
20-80% humidity (non-condensing)
D
imensions
:
53
(
W
)
x 173
(
H
)
x 164
(
D
)
mm
Power Consum
p
tion
:
Max. 25W, Avera
g
e 17W
Seek Time
:
M
a
x. 11 milli
seco
n
ds
U
SB Standards
:
USB Specification Rev. 2.
0

USA/Canada Technical Support is available 24 hours a day, 7 days a week
Toll-Free: 866-752-6210
email: [email protected]
Europe Technical Support is available between 9am-6pm (Monday-Thursday) (GMT)
and 9am-4:30pm on Fridays.
email: [e-mail]
©2005, Buffalo Technology (USA), Inc.
http://www.buffalotech.com