Buffalo TeraStation Live HS-DH-TGL/R5 User manual

User Manual
TeraStation Live
HS-DHTGL/R5
www.buffalotech.com v1.0

2
Introduction
Congratulations on your new TeraStation! This user manual is intended to assist you in
confi guring it.
Because we’re constantly updating our product, the images and text in this manual may vary
slightly from the images and text displayed by your TeraStation. These changes are minor
and should not affect the ease of setup adversely. As time passes, future user interfaces,
updated software, and later versions of this manual may be freely available for download at
our web site: http://www.buffalotech.com.
If you run into diffi culties or need additional help, feel free to contact our technical support.
Contact information for Buffalo Technology and our technical support is available on pages
80 and 81.

3
Table of Contents
TeraStation Quick Setup...................................................4
Installing Software ............................................................8
Accessing TeraStation Data from a PC............................. 11
Accessing TeraStation Data from a Mac...........................15
TeraStation Layout..........................................................20
Advanced Settings........................................................... 23
Network Settings.............................................................27
Hard Drive Settings.........................................................29
Adding Extra Hard Drives ...............................................36
Shared Folders................................................................ 40
Groups ...........................................................................45
Users ..............................................................................46
Troubleshooting Multiple Shares.....................................48
Backups .........................................................................50
Maintenance Settings......................................................60
PCast and DLNA .............................................................54
System Information.........................................................66
Client Utility ...................................................................71
Troubleshooting .............................................................. 74
Safety Warning ...............................................................75
Changing Hard Drives..................................................... 76
Technical Specifi cations ..................................................80
Technical Support...........................................................81
GPL Information .............................................................83

4
Begin setting up your TeraStation by plugging
your power cable and Ethernet cable into the
back of the TeraStation as shown.
TeraStation Quick Setup

5
Plug the power cord into a wall socket or
surge protector. Plug type and socket will
differ according to country of use.
Plug the other end of the Ethernet cable into
a hub, router, or switch in your network.
TeraStation Quick Setup
Connect your cables

6
TeraStation Quick Setup
Press the power button on the front panel. LEDs will
light as your TeraStation boots up.
After your TeraStation has completed booting up, check
the LINK/ACT LED on the front of the TeraStation. If
it’s lit, then your TeraStation is connected properly, and
you can go on to page 8. If it’s not lit, turn to page 7 for
troubleshooting.

7
The TeraStation’s Ethernet port will automatically adjust to use either a Crossover or Patch cable,
so you may connect the TeraStation to your network with either type of Ethernet cable. Buffalo
Technology doesn’t recommend connecting the TeraStation directly to a PC.
Verify that the LINK/ACT LED on the front of TeraStation is lit (see page 6’s picture). If it’s lit, go to
page 8 to continue setting up TeraStation. If the LINK/ACT LED is still not lit, try the suggestions
below to verify that you’re not suffering from common setup problems.
Having problems? Make sure that:
•the TeraStation and the router, hub or switch are both powered on,
•the Ethernet cable is securely plugged in at both ends, and
•the Ethernet cable is not damaged. Verify this by trying a different Ethernet cable.
If problems persist, you may contact Buffalo Technology’s technical support. See pages 66 and 67
for technical support contact information.
TeraStation Quick Setup

8
Installing Software
Insert the TeraNavigator CD into your computer’s CD-ROM drive.
On a PC, setup should automatically launch. If it does not, manually
launch setup.exe by pressing Start and selecting the Run... option.
When the Run dialog opens, type d:\TSnavi.exe (where d is the drive
letter of your CD-ROM drive). Press OK to continue.
If you are installing the software on a Mac, open the CD and click
TeraNavigator to begin installation.

9
TeraNavigator Setup
Press the Begin Installation button to begin.
If you’re installing on a PC, click on Connect this PC to
TeraStation (the green, lower button). Mac users can skip this
step.
Click Next to step through the installation.

10
TeraNavigator Setup
Continue pressing Next to step through the installation.
When installation is complete, you may close the installation
window.