Bullard TI Commander User manual

Bullard TI Commander™ Thermal Imager
User Manual
Table of Contents
Imager Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Use and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . .4
Palm andTop Straps . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Care Instructions/Replacing Display Cover . . . . . . . 6
Service/Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . 8
Congratulations
Congratulations on the purchase of your new Bullard TI
Commander Thermal Imager. The Bullard TI Commander
combines advanced thermal imaging performance and
unsurpassed firefighting features with Bullard’s expertise
in high heat, impact resistant thermoplastics. Its
innovative design, extensive feature set, and legendary
durability make the BullardTI Commander the best choice
for firefighters who demand maximum performance and
flexibility.
The benefits of using thermal imaging technology as a
firefighting tool encompass just about every aspect of a
firefighter’s job. Thermal imaging is not, however, a
technology designed to replace current firefighting tactics.
Rather, it is a tool that allows the firefighter to be more
effective and make better decisions. Some of the many
uses for your BullardThermal Imager include:
• Search and rescue
• Scene assessment
• Locating the seat of the fire
• Determining the spread of the fire
• Locating hot spots
• Identifying potential flashover situations
• Determining ventilation points
• Determining entry and exit points
• Overhaul
• Hazmat
•Wildland firefighting
• Incident Investigation
•Training
NOTE
To ensure that we are able to reach you
with any product or software updates,
please fill out the warranty card enclosed
with your BullardTI Commander Thermal
Imager.
Read all instructions and warnings before using this
product. Failure to observe this information could result
in death or serious injury.
WARNING

Imager Diagram
2
Lens
Relative Heat Indicator™ (6)
(Optional)
Pistol Grip (10)
Transmit Button (3)
(Optional)
On/Off/Sleep Button (1)
2X Digital Zoom (5)
(Optional)
Battery
Compartment (7)
Charge and Data
Output Port (11)
LCD Screen
Top Strap (12) Rear Boot Polycarbonate
Display Cover (9)
Lens Bezel (8)
Bullard TI Commander Thermal Imager
Figure 1
ThermalThrottle (2)
Image Capture (4)
(Optional)
Palm Strap (13)

Bullard TI Commander™ Thermal Imager
User Manual
3
Use and Operation
Power
To turn on the BullardTI Commander, depress the large red
“On/Off”button(Item 1, Figure 1) ontheleftsideofthe
unit for approximately one second until the light in the red
button illuminates and remains on.TheTI Commander will
takeapproximately 15secondstoself-calibrateandbecome
operational.Duringthe power-upsequence,youwillseethe
Bullardlogo ortheoptionalcustomlogoonthedisplay.After
thethermalimage appears,theunit isreadyforuse.Toturn
off the Bullard TI Commander, depress and hold the red
“On/Off” button. Continue to depress the button until the
red light in the “On/Off” button has turned off.
The approximate battery level is indicated by the colored
circles on the left side of the screen.When the red circle is
filled,thebatteryhasapproximately8minutesof operating
time remaining. With about 4 minutes of operating time
remaining, the words “LOW BAT” will appear and blink
below the battery indicator to indicate an extremely low
battery. The operating time without the transmitter
activated is approximately 80 minutes.
NOTE
If the TI Commander is turned off when
the battery indicator is on the red circle,
theremaybe insufficientpowerremaining
for the unit to power up. If this occurs,
replace the depleted battery with a fully
charged battery.
Sleep Mode
To conserve battery life, the Bullard TI Commander
includes a“Sleep”feature.Toput the unit into sleep mode,
briefly press and release the “On/Off” button (Item 1,
Figure 1).The unit will immediately initiate sleep mode.
The red “On/Off” button will blink indicating that the unit
isinsleepmode.Tobringtheunitoutofsleepmode,briefly
press and release the red “On/Off” button. The thermal
image will immediately reappear on the screen and theTI
Commanderisfully operational.Thisfeaturecanbehelpful
during a fire company’s response to an incident.The user
can activate theTI Commander during the response, then
place the imager in sleep. This provides an “instant on”
capability for immediate use at an incident.
Thermal Throttle
The Bullard TI Commander features a fully adjustable
aperture, orThermalThrottle, which optimizes the thermal
image and enables advanced scene assessment. Simply
put, the Thermal Throttle is a manual iris control that
regulates the amount of energy that reaches the thermal
detector.The process is similar to that of the pupil in the
eye. When there is bright light the pupil shrinks. When
there is low light the pupil expands.TheThermalThrottle
works the same way. In high heat situations, theThermal
Throttle may be reduced down to obtain the best contrast
andtheclearest image.Inlowheatsituations,theThermal
Throttle should be wide open. Since theThermalThrottle is
manually adjusted, the operator can always get the
clearest image.TheThermalThrottle is manually adjusted
by turning theThermalThrottle dial on the front left of the
unit (Item 2, Figure 1). Turning the dial clockwise
(toward the lens) closes the Thermal Throttle, turning it
counterclockwise opens the Thermal Throttle. For
increased durability, theThermalThrottle is equipped with
a safety slip mechanism, which engages when theThermal
Throttlereachesthe fullyopenorfullyclosed position.This
mechanism prevents over-adjusting or over-tightening the
dial.
Bullard recommends the following Thermal
Throttle adjusting procedure:
Once the unit is turned on and the internal calibration is
completed, turn the Thermal Throttle clockwise until the
image on the screen disappears. This is the closed
reference position.Then turn theThermalThrottle knob in
the opposite direction until the picture contrast is to your
liking. It should take less than one full revolution of the
ThermalThrottle to completely open the iris. Once the iris
is fully open, the safety slip mechanism engages to ensure
the Thermal Throttle is not over-tightened. Continuing to
turnthedialbeyondthatfirstfullrevolution willnotchange
the image.
NOTE
Most of the needed adjustment will be
accomplishedwithinabout1/4ofaturnof
theThermalThrottle.TheThermalThrottle
will not completely close.
Installable Accessories:
The Bullard TI Commander can be equipped with the
following optional accessories:
•Wireless Transmission – enables remote video
monitoring of the image on the thermal imager
(Item 3, Figure 1)
• Digital Image Capture – capture thermal imaging still
images for later retrieval via a personal computer
(Item 4, Figure 1)
• Digital Zoom – digitally zooms the thermal image to
twice the standard size (Item 5, Figure 1)
• Relative Heat Indicator – Measures approximate
temperature of objects (Item 6, Figure 1)
If yourTI Commander has been installed with any of these
options, refer to the Accessories for Bullard TI
Commander User Manual for setup and operational
instructions.
NOTE
TheTI Commander also can supply hard-
wire video out via the data/direct charge
port. A video out cable (part number
CMDRCACABLE) can be purchased to
enable video-out to an external source.
Use and Operation

Charging the Battery
4
Charging the Nickel Metal Hydride Battery
Using the Battery Charger
The battery should be charged in the battery charger,
usingeithertheACorDCadapter provided (Figure 2).
Properly connect the power supply to a power source.
To charge a battery, insert it into the charger so that the
metalcontactsonthebattery are aligned withthemetal
connectors in the charger. A red light will illuminate on
the charger to indicate that the battery is charging.
When the light on the charger turns to green, the
batterywillbefullycharged,andthechargerwillinitiate
a trickle charge to maintain the battery’s charge. You
may leave the battery in the charger indefinitely as it
will not overcharge.
NOTE
If you do not see the red LED illuminate
when you place a battery into the
charger, the battery is not charging.
Using the Direct Charge System
The direct charge system will allow the battery of the
BullardTI Commander to be charged inside the camera.
The standard battery charger should be connected to a
power supply using the AC or DC adapter provided.
Connect the charger to the thermal imager by using the
gray direct charge cord provided (Figure 3). Insert
one end of the cord into the charger using the outlet
provided on the front of the charger and the other end
into the direct charge plug (Item 11, Figure 1) located
on the handle of the thermal imager (Item 10, Figure
1). To connect the cable, lift the connector port cover
with one hand while inserting the cable into the port
with the other hand. The connector is shaped and
directional, so be sure that it is properly aligned so that
it seats fully in the receiver port.
NOTE
To ensure that the cable stays in place, rotate
the screw-in connector ring to lock the cable
to the plug.The threaded connector ring must
be screwed down completely to ensure
proper conection and charging operation.
A red light will illuminate on the charger to indicate that
the battery is charging. When the light on the charger
turns to green, the battery is fully charged. You may
leave the direct charge system in place indefinitely as
the batteries will not overcharge.
Using the Direct Charge System/Battery
Charger
A battery can be charged in the charger at the same
time as the battery in the camera is being charged by
using the directions previously mentioned. Charging
both batteries at the same time will not cause any
damage to the batteries or charging unit.
Loading the Battery
Toopenthebattery compartment(Item 7, Figure 1),
turn the two thumb knobs outward and pull the door
open. Remove the used battery. Insert a fully charged
battery making sure the Bullard decal is facing away
from the camera and the text is right side up. If the
batteryhasnotbeeninsertedcorrectly,thedoorwill not
completelyshutandthe thumbknobscannotbe secured
properly. If the door will not shut, remove the battery
and review the instructions above. The battery can
easily be replaced in the dark. To do so, simply locate
the notched top of the battery.The notch goes into the
battery compartment first, on the left side as you are
looking at the LCD display. If the door will not shut,
remove the battery and try again. Additionally, as with
all batteries, the Bullard rechargeable battery will
experience a slow drain of its charge during storage.
The amount of drain varies widely based on storage
conditions. For best performance, charge each of the
batteries every two weeks.
NOTE
To extend the potential lifespan of your
batteries,fullydrainandrechargeeach
battery monthly.To help extend the life
of the rechargeable batteries and
prevent unexpected instances of
uncharged batteries, develop a clear,
formalized plan for maintaining,
charging and replacing your batteries.
The TI Commander comes with two
ultra performance NiMH batteries.
Using standard NiMH batteries from
Bullard will result in significantly lower
operating time performance.
12 VDC Adapter Figure 2
110 VAC Power Supply Dual Charger Base
Figure 3

Bullard TI Commander™ Thermal Imager
User Manual
Palm and Top Straps
5
Palm and Top Straps
The palm and top straps (Item 12, 13, Figure 1) are
designedtoallowthe user toreplacethetop and sidestrap
without having to return the unit to the factory.
Replacing the Palm Strap
Using a 3/8" wrench, remove the nut on the right side of
the strap. Remove the strap from the screw by lifting away
from the camera. Remove the left side of the strap by
removing the screw with a Phillips screwdriver. The new
strap should be attached by first securing the left bracket
to the camera using the existing screw. The right bracket
shouldthenbesecuredbyplacingthebracketonthe screw
andtighteningthenut.Thestrapiscorrectlyattachedwhen
the Bullard logo or custom lettering is facing outward.
Adjusting the Palm Strap
To adjust the palm strap on the side of the unit, pull open the
leather hand guard and readjust the strap. Once adjusted to
comfortable length, close the leather hand guard.
Adjusting the Shoulder Strap
To attach the shoulder strap, clip the hooks to any of the
three D-rings on the unit. Adjust the strap to a comfortable
length.
Replacing the Top Strap
Unwrap the leather pad from the strap to expose the ends
of the strap. Remove the right side of the strap from the
Velcro. Wrap the end around the anchor on the top of the
camera and re-attach to the Velcro. Remove the left side of
the strap from the Velcro, wrap the end around the anchor
on the top of the camera and re-attach to the Velcro.Wrap
the leather pad around the strap ends.
Wrist Strap
Thisstrap canbeusedasa backup tokeeptheimager from
falling if it should slip from your hand.The adjustable strap
fits over the sleeve of your turnout gear and can adjust to
anysizewrist.Thewrist strap can be easily attached to any
D-ring located on the camera.
Top Strap
Palm Strap
Wrist Strap

Care Instructions/Replacing Display Cover
6
Care Instructions
The design of the BullardTI Commander requires ongoing,
but relatively simple maintenance. For best results,
after each use:
• Ensure that all straps, bumpers, and screws are intact
and working properly. The display cover, straps, and
rubber bumpers are field replaceable.
• Ensure that all screws on rubber bumpers, side strap,
battery door, and display are tight and secure.
• Clean the outside of the unit with a rag or cloth using
mild soap or detergent. Do not submerge the imager in
water to clean it. Use isopropyl alcohol on stubborn
stains.
•Wipe the lens with a soft, damp cloth.
• Clean the display cover with a soft, damp cloth.
• If the unit is equipped with a Relative Heat Indicator, the
temperaturesensor(pyrometer)lens should beroutinely
cleaned using a mild detergent applied with a soft cloth
or cotton swab.
• Check the unit for any damage or cracks. Immediately
report any evidence of damage or operational problems
to your distributor or to the Bullard Service Center so
required service can be performed.
• When not in use, always store your Bullard TI
Commander in the case provided or in the optional truck
mount.
•Allthermalimagersshould be maintainedusingaproper
program of preventative maintenance.
Cleaning the Lens
The BullardTI lens is protected by both a silicone gasket
and a plastic lens bezel. The bezel (Item 8, Figure 1)
containsadrainhole so thatanywaterthatmaygetintoor
behind the bezel will be effectively drained away.The lens
can be cleaned with a soft cloth and soapy water (see
other care instructions above).
Replacing the Video Display Cover Window
The display cover (Item 9, Figure 1) has a scratch
resistant hard coating to minimize marring. However, if
heavy scratching or gouging does occur, the cover can be
replaced.To do this, simply remove the four stainless steel
screwsalong thetopandsidesofthewindow.Thenremove
the battery door thumb knobs by loosening the two screws
that retain them. Remove the plastic display cover and
replace with a new one (part numberTIWINDOW), making
surethattheO-ringcountersinkslotsaroundthemounting
holes are facing outward. When reinserting the screws,
make sure each one has the sealing O-ring in place.
CAUTION
Do not use solvents, paint thinners or ANY Hydrocarbon-
based material to clean your Bullard TI Commander as
they could permanently mar the surface or degrade the
protective properties of the casing.
Ensure that the BullardTI Commander always has each of
its three protective rubber bumpers properly affixed and
that all screws remain tightened.
Do not intentionally submerge the unit underwater or
subject the unit to high pressure water. Follow care
instructions described above.
Do not leave the battery door open during use, while lying
idle, or during storage.
Failureto observetheseinstructionsmay resultinproduct
damage. Any damage caused by improper care is not
covered under warranty.
WARNING
Do not attempt to disassemble the Bullard TI
Commander. If the unit is not functioning promptly
return it to Bullard for evaluation. Disassembling the
unit voids all warranties.
Like all thermal imagers sold at the time of this printing,
the BullardTI Commander is not certified as intrinsically
safe.
ThermalImagingisnot atechnologydesigned toreplace
current fire fighting tactics. Rather, it is a tool that
allows the firefighter to be more effective and to make
better decisions.
Firefighters cannot stop using basic firefighter safety
tactics. All firefighters should receive proper training
on: how thermal imagers work; the uses and limitations
ofthermalimagers; imageinterpretation;and thesafety
considerations for thermal imaging use. Do not attempt
to remove the lens gasket or the rear boot.These parts
providesealingand removalwillbreakthe sealexposing
the unit to potential water damage. Failure to follow
these instructions could result in death, serious injury
and/or product damage.

Bullard TI Commander™ Thermal Imager
User Manual
Service/Warranty
7
Service
If your Bullard Thermal Imager is not performing properly,
pleasecontact BullardTechnicalSupportat877-BULLARD(285-
5273), or [phone]. Describe the problem to the
Bullard representative as completely as possible. Please have
theimagerwithyouwhen youcall. Foryourconvenience,your
representativemaytrytohelpyoucorrecttheproblemoverthe
phone. Before returning your Bullard TI Commander Thermal
Imager, you should:
1.Verify with your representative that the product should be
returned to Bullard. The Bullard Technical Support/Service
Centerwillprovideyouwithwrittenpermission and a return
authorization number.
2.Decontaminate and clean your Thermal Imager to remove
any hazardous or contaminated materials that may have
settled on the product during use. Laws and/or shipping
regulations prohibit the shipment of hazardous or
contaminated materials. Products suspected of
contamination will be professionally decontaminated at the
owner’s expense.
3.Shipreturned products,includingthose underwarranty,with
all transportation charges pre-paid. Bullard cannot accept
returned goods on a freight-collect basis.
Returned products will be inspected upon return to the Bullard
facility. If the repair is under warranty, Bullard will repair the
unit and ship it from our factory within two business days.
If the return is a non-warranty repair, a Bullard Technical
SupportRepresentativeoryourlocaldistributorwillcontactyou
withnotificationthatan estimatehasbeenprepared.Your local
distributor will provide you with a repair invoice estimate.To
authorize repair, you must provide a purchase order to your
distributor for the amount of the estimate. Once Bullard
receives authorization from your local distributor, Bullard will
repair the unit and ship it from our factory within two business
days. If the cost of repairs exceeds the stated quote by more
than 15% or by more than $100, Bullard will re-estimate your
repair and your local distributor will contact you for
authorization to complete repairs. After repairs are completed
and the goods have been returned to you, your distributor will
invoice you for the actual repair amount.
Warranty
Bullard warrants to the original purchaser that the BullardTI
Commander and all features/accessories installed in the unit
are free of defects in materials and workmanship under
intendeduseandservice fora period ofone(1)yearfromdate
of manufacture. Bullard’s obligation under this warranty is
limited to repairing or replacing, at Bullard’s option, articles
that are returned within the warranty period and that, after
examination, are shown to Bullard’s satisfaction to be
defective, subject to the following limitations:
a)Article must be returned to Bullard with shipping charges
prepaid.
b) Article must not be altered from its original configuration.
c)Articlesmustnothavebeenmisused,abused,ordamagedin
transport.
d)Maintenance and field replaceable items, if defective, are
covered under warranty for a ninety (90) day period.
These items include:
• Batteries
• Straps
• Rubber bumpers
• Battery chargers
• Display covers
• AC/DC adapters
• Direct charge and data cables
•Allaccessoriesexcept thoseinstalledinsidethe BullardTI
Commander
Bullard provides a limited lifetime warranty on the TI
Commander outer shell. This warrants that the outer shell is
free of defects in materials and workmanship under intended
use and service for the original purchaser. Bullard’s obligation
under this warranty is limited to repairing or replacing, at
Bullard’s option, articles that after examination are shown to
Bullard’s satisfaction to be defective, subject to the following
limitations:
1.Before an article is returned to Bullard, a Return
Authorization(RA)numbermustfirstbesuppliedbyaBullard
Customer Service Representative..
2. Article must not be altered from its original configuration.
3. Article must not have been misused, abused, or damaged in
transport.
4.WhentheoutershellisobsoleteandBullardnolongerstocks
the part, the limited lifetime warranty will be terminated.
In no event shall Bullard be responsible for damages, loss of
use,orotherindirect,incidental,consequentialorspecialcosts,
expenses or damages incurred by the purchaser,
notwithstandingthatBullard hasbeenadvisedof thepossibility
of such damages.
Any implied warranties, including warranties of
merchantability and fitness for a particular purpose,
are limited in duration to one (1) year from the date
of manufacture of this product.
Some states do not allow the exclusion or limitation of
incidental or consequential damages, or allow limitations on
howlonganimpliedwarrantylasts, so the above limitationsor
exclusions may not apply to you. This warranty gives you
specific legal rights, and you may have other rights which vary
from state to state.
Extended Warranty
The extended warranty has all the same terms and conditions
as the one-year warranty, except it is for the period of two
years.This warranty can be purchased through any authorized
Bullard distributor.

©2005 Bullard. All rights reserved.
Bullard is a registered trademark of Bullard.
“It’s your life and you’re worth it”,TI Commander, and
Relative Heat Indicator are trademarks of Bullard.
Ultem is a registered trademark of General Electric Company.
Velcro is a registered trademark of Velcro USA.
6050037062 (0905)
ISO 9001
certified
Bullard
1898 Safety Way
Cynthiana, KY 41031-9303
Toll free: +877-BULLARD (285-5273)
Tel: [phone]
Fax: [phone]
www.bullard.com
www.thermalimager.com
Bullard GmbH
Hochkreuzallee 36
53175 Bonn-Bad Godesberg
Germany
Tel: [phone]
Fax: [phone]
www.bullardextrem.com
Respiratory
Protection Fire and Rescue Safety
Head
Protection Thermal
Imaging
CMD Includes Bullard TI Commander with direct charge system, two
premium 10V NiMH rechargeable batteries, battery charger with
110VAC,and 15VDCadapters,wrist strap,shoulder strap,multimedia,
interactiveproduct orientationCD, andheavyduty carryingcase
CMDFF Includes Bullard TI Commander with digital zoom, image capture,
Relative Heat Indicator, and custom startup graphics. Also includes
directchargesystem,twopremium 10V NiMHrechargeablebatteries,
battery charger with 110VAC, and 15VDC adapters, wrist strap,
shoulder strap, multimedia, interactive product orientation CD, and
heavyduty carryingcase.Doesnot includetransmitter.
CMDEXT 1yearextended warrantyforTICommander
CMDUPGRADE UpgradesaTIxmodeltoaTICommander–includes5inchdisplayand
upgradeddirect chargeport andcable.Can be equippedwith optional
features.
CMDTRANS Package includes 4 channel wireless remote transmitter, omni-
directionalantenna,4channelreceiverswitchbox,110VAC,and15VDC
adaptersand allnecessarycables
CMDTRANS2 Package includes 2 channel wireless remote transmitter, omni-
directionalantenna,2channelreceiverswitchbox,110VAC,and15VDC
adapters,and allnecessarycables
CMDTRANSONLY 4channelwirelessremotetransmitter–receivingsystemnotincluded
CMDTRANSONLY2 2channelwirelessremotetransmitter–receivingsystemnotincluded
REC 4channelreceiversystemincludesomni-directionalantenna,4channel
receiver switch box, 110VAC, and 15VDC adapters, and all necessary
cablesforreceivingtransmitted videosignal
REC2 2channelreceiversystemincludesomni-directionalantenna,2channel
receiver switch box, 110VAC, and 15VDC adapters, and all necessary
cablesforreceivingtransmitted videosignal
MCC1 2 channel Mobile Command Center. Includes Sony recorder, 5” LCD
screen, two BATTERYNIMHULTRA batteries, hard case, and all
necessarycables forreceiving transmittedvideosignal.
MCC2 2 channel Mobile Command Center. Includes 5” LCD screen, two
BATTERYNIMHULTRAbatteries,hardcase,andallnecessarycablesfor
receivingtransmitted videosignal. Sonyrecordernot included.
MCC3 4 channel Mobile Command Center. Includes Sony recorder, 5” LCD
screen, two BATTERYNIMHULTRA batteries, hard case, and all
necessarycables forreceiving transmittedvideosignal.
MCC4 4 channel Mobile Command Center. Includes 5” LCD screen, two
BATTERYNIMHULTRAbatteries,hardcase,andallnecessarycablesfor
receivingtransmitted videosignal. Sonyrecordernot included.
ML1 2 channel MobileLink handheld receiver. Includes battery, battery
charger, andAC/DCadaptors.
ML2 2channelMobileLink handheldreceiver only.
ML3 4 channel MobileLink handheld receiver. Includes battery, battery
charger, andAC/DCadaptors.
ML4 4channelMobileLink handheldreceiver only.
CMDEXT TICommander One-Year ExtendedWarranty
CMDZOOM TI Commander 2X Digital Zoom Optional Accessory – enables
magnificationof viewedscenetozoom inonfar awayobjects.
CMDCAPTURE TI Commander Digital Image Capture Optional Accessory – enables
digital capturing of 24 thermal images for download to a personal
computer(includessoftwarediskanddatacableforfiletransfertoaPC)
CMDRHI TI Commander Relative Heat Indicator Optional Accessory – enables
relativeheat (temperature)measurementof objectsina scene
CMDGRAPH TI Commander Startup Graphics Option – factory supplied graphics
with your department’s name appearing on display screen during
startup
CMDCUSTGRAPH TI Commander Startup Custom Graphics Option – customer supplied
custom text, logo, or other graphics that appear on display during
startup
CMDDCCABLE TICommander DirectChargeCableforusewith directchargesystem
CMDDATACABLE TICommanderDataTransferCableforusewithDigitalImageCapture
accessory
CMDRCACABLE TICommanderRCA cableenablesvideo-out toan externalmonitoring
orrecording device
BATTERYNIMHULTRA Ultra-Performance 10VNiMHBattery
TIGLARESHIELD Attaches to Bullard TI Commander reducing glare in bright sun
conditions
TRIPOD Heavy-dutyfourfoot tripodfor BullardTI Commander
CLAMP ClampingsystemforusewithBullardTICommanderorasstandalone
systemto mountimagerto almostanysurface
SHSTRAP ReplacementShoulder strap
STRAPKIT ReplacementPalm,Top,andWristStrap Kit
CMDWINDOW TICommanderreplacementHard-coatedPolycarbonateVideoDisplay
cover
DUALCHARGERBASE Replacement12-24VDC DualChargerBase
15VADAPTOR ReplacementACAdaptor
CARADAPTOR ReplacementDC vehicleadaptor
BUMPERKIT ReplacementBumper Kitincludesall threebumpersand hardware
TISP PersonalizedSide Strap
CMDKIT Parts kit includes common replacement parts at reduced cost versus
separate purchase. Kit includes bumpers, side and top straps,
replacementdisplay cover, batteryanddirect chargepowercord
TIPMCMD Factory-provided refurbishment of unit; includes replacement of outer
shellandallmaintenanceparts;completediagnosticofthermalimager
engineand electronics
OMNI Omnidirectional antennawithpermanent andmagneticmounts
OMINONLY Omni directionalantenna– antennamountsnot included
Ordering Information
CATALOG NUMBER DESCRIPTION CATALOG NUMBER DESCRIPTION