Bullard CEN10 Owner's manual

READ ALL INSTRUCTIONS AND WARNINGS
BEFORE WEARING THIS HELMET
Carefully read and understand these instructions. Use this
helmet exclusively for the activities for which it is certified
(see labeling) and in strict accordance with ANSI/ISEA Z89.1.
Please refer to the shell label for specific standard “Type” and
“Class.”
WARNING
Hard hats/helmets are designed to provide limited protection
to the head by reducing the force of falling objects striking
the top of the hat shell. While limited protection is provided
in other parts of the shell, this helmet was not designed to
provide front, side, or rear impact protection. Avoid contact
with electrical wires. Never alter or modify the shell or
suspension system. Always use Bullard replacement parts.
Improper use of this helmet can cause serious or fatal injury.
If the instructions are not followed correctly the level of
protection offered by the helmet can be significantly reduced.
Inspect your helmet regularly. Check for cracks and
any sign of damage before each use. Replace helmet
immediately if you notice any signs of wear, damage, abuse,
or environmental degradation. If the helmet has sustained a
forcible blow/impact, dispose of immediately, even if damage
is not visible. Failure to follow these warnings could result in
death or serious injury.
Intended use of this helmet involves activities that are
extremely dangerous. Failure to follow these instructions
and any of these warnings may result in serious injury or
even death.
For adequate protection this helmet must fit or be adjusted
to the size of wearer’s head (see Adjusting the Suspension
Size below). The helmet is made to absorb the energy of a
blow by partial destruction to the shell or foam liner, and even
though such damage may not be readily apparent, any helmet
subjected to severe impact should be replaced. The attention
of users is also drawn to the danger of modifying or removing
any of the original component parts of the helmet other than
as recommended by the helmet manufacturer. Helmets
should not be adapted for the purpose of fitting attachments
in any way not recommended by the helmet manufacture.
Do not apply paints, solvents, adhesives, or self-adhesives
except in accordance with instructions from the helmet
manufacturer. Minimum operating temperatures as marked.
Provides electrical insulation as marked.
INSTRUCTIONS FOR USE
Adjusting the Suspension
Size:
The Cen10 helmet is equipped with
the FlexGen ratchet suspension. To
adjust the suspension, turn ratchet
knob counterclockwise until
headband opens to largest size.
Place helmet on your headand turn
ratchet clockwise until it fits comfortably snug.
DO NOT OVERTIGHTEN. See Figure 1
Replacement Recommendations:
Bullard recommends replacement every 12-18 months or more
frequently as needed for key replaceable parts such as the
comfort crown pad liner, ratchet cover, brow pads, and chin
strap.
Replacement Parts Instructions:
The comfort crown pad liner, ratchet cover, and brow are easily
removed as these are attached via Velcro. To remove and
replace the chin strap, unclip from the helmet and attach new
piece. See Figure 2
Cleaning, Replacing, and Storage:
Clean the helmet with mild soap and lukewarm water. Do not
use paint, solvents, chemicals, adhesives, gasoline, or like
substances on this helmet. The impact resistance and other
protective properties of the helmet may be diminished by such
substances. Damage caused by these substances may not be
apparent or readily detectable by the user.
Safety Helmet Use and Care Booklet
For Industrial Use
www.bullard.com
To Remove To Lock
Figure 1
Figure 2

www.bullard.com
NOTE:
Stickers may contain materials that in time can alter the
physical properties of the helmet. Before applying any of
these products, verify their compatibility with PC/ABS.
Service Life:
This helmet does not have an indefinite service life. Conditions
found in many work environments such as exposure to
ultraviolet light, temperature extremes, chemical exposure,
and wear and tear from daily use will reduce the protective
properties of the helmet over time.
The helmet in its entirety should be replaced every five years.
Please refer to your company guidelines to see if your employer
has a specific replacement program. It is noted that you
must inspect your helmet regularly for cracks or any damage
before use. If any damage appears, this will compromise the
protection the helmet is providing. It is noted that while Bullard
is recommending replacement of the helmet every 5 years, due
to working condition such as environment, storage of helmet,
chemical exposure, etc., you may need to replace the helmet
prior to the 5 year mark.
Storage:
Store helmet in clean, dry environment, not over 120 degrees
(49 degree C). Do not store in direct sunlight. Do not store
helmet in areas such as the dashboard of an automobile or
truck bed of work vehicle.
Three-Year Limited Warranty
Bullard warrants to the original purchaser that the helmet
system is free of defects in materials and workmanship under
normal use and service for a period of three years from the
date of manufacture. Under this warranty, Bullard’s obligation
is limited to repairing or replacing articles that are returned
within the warranty period and that, after examination, are
shown to Bullard’s satisfaction to be defective, subject to
following limitations:
• Helmet must be returned to Bullard with shipping charges
prepaid;
• Helmet must not be altered from its original factory
configuration; and
• Helmet must not have been misused, abused, or damaged in
storage or transit.
In no event shall Bullard be responsible for damages resulting
from loss of use or other indirect, incidental, consequential
or special costs, expenses or damages incurred by purchaser,
notwithstanding that Bullard has been advised of the possibility
of such damages.
ANY IMPLIED WARRANTIES, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE,
ARE LIMITED TO THREE (3) YEARS FROM THE DATE THE
PRODUCT WAS MANUFACTURED.
The above imitations or exclusions may not apply in all states.
Some states do not allow the exclusion or limitations of
incidental or consequential damages or allow limitations on
how long an implied warranty lasts. This warranty gives you
specific legal rights, and you may have other rights which vary
between states.
Return Authorization:
Contact Bullard Customer Service to obtain written permission
to return product. Material returned for credit will be subject
to factory inspection.
Current products or products under warranty may be subject
to a restocking charge. Returned articles should be sent to
Bullard with shipping prepaid.
2
Service Life and Warranty

www.bullard.com
Use and care booklet
Cen10 Safety Helmet
For Industrial Use
3
Helmet Diagram
Accessory Clips
Shell
Foam
Comfort Liner Replacement
Part #: C10CROWNLINER Suspension Replacement
Part #: C10CROWNLINER
Chin Strap Replacement
Part #: C10CHINSTRAP
Browpad Replacement Part
Number: C10BROWPAD Nape Comfort Pad Replacement
Part Number: C10NAPEPAD

©2022 Bullard. All rights reserved.
60210012242C (0322)
www.bullard.com
Bullard Center
2421 Fortune Drive
Lexington, KY 40509 • USA
877-BULLARD (285-5273)
Tel: [phone]
Fax: [phone]
Americas Operations
1898 Safety Way
Cynthiana, KY 41031 • USA
877-BULLARD (285-5273)
Tel: [phone]
Fax: [phone]
Bullard GmbH
Dieselstrasse 8a
53424 Remagen • Germany
Tel: [phone]
Fax: [phone]
Bullard Asia Pacific Pte. Ltd.
51 Changi Business Park Central 2
#03-04 The Signature
Singapore 486066
Tel: [phone]