Bunn TF 1.0 Gallon Owner's manual

BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: [phone] FAX: [phone]
35075.0001 04/08 ©2006 Bunn-O-Matic Corporation www.bunn.com
USE & CARE INFORMATION
CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE 1 of DAILY CLEANING.
1.0 & 1.5 Gallon
TF SERVER
(With & Without Base)
Black Decor
Stainless Steel Decor

2
INTRODUCTION
This server is intended for use with a BUNN®DUAL®TF DBC, SINGLE®TF DBC or ICB coffee brewer only.
When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server
and then transported to a remote serving location. The server must be placed on a sturdy counter or shelf.
USER NOTICES
The notices on this server should be kept in good condition. Replace unreadable or damaged labels.
DAILY CLEANING
CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY
NOTE: Bunn-O-Matic recommends the 3 step method for cleaning and sanitizing the server. The 3 step method
consists of hot soapy water using an approved detergent, a fresh water rinse, and an aqueous sanitizing
solution using an approved non-chlorine sanitizer. Do not submerge server.
1. Run a complete brew cycle of just hot water into the server and let it set for a minute. Empty the server
completely by opening the faucet.
2. Remove the lid, fill server with cleaning solution and thoroughly clean the inside of server.
3. Rinse server thoroughly using fresh water rinse.
4. Fully fill server with sanitizing solution for 5 minutes then drain through fully open faucet.
5. Remove the large plastic cover from the bottom of the server, then remove the clamps and silicone tube from
the server.
6. Remove the faucet handle/stem assembly by unscrewing the faucet nut just beneath the faucet handle.
7. Remove sight gauge shroud by pulling straight up. Remove sight gauge tube and washers.
8. Use enclosed cleaning brush to thoroughly clean the fill tube of the lid assembly, faucet, and sight gauge
tube.
9. Disassemble the faucet/stem assembly. Thoroughly wash all faucet parts, lid, and silicone tube in a mild
detergent and water solution. Rinse the parts in hot water. Sanitize the parts for five minutes, then air dry
completely.
10. Reassemble the faucet and attach it, the lid, sight gauge and silicone tube to the dispenser.
11. Wash the entire outside surface of the server with a clean damp cloth.
#26186.0000
35075.1 060107

3
REPLACEMENT PARTS
1. 39082.1000 Shroud, Sight Gauge 1.5 Gal.
(Includes Item 4)
39082.1001 Shroud, Sight Gauge 1.0 Gal.
(Includes Item 4)
2. 35010.0000 Plate, Decal Mounting
3. 35009.0000 Decal, Bunn
35009.0001 Decal, Plain Black
4. 35004.0000 Backing, Sight Gauge 1.5 Gal.
35004.0001 Backing, Sight Gauge 1.0 Gal.
5. 35005.0000 Sight Gauge Tube 1.5 Gal.
35005.0001 Sight Gauge Tube 1.0 Gal.
6. 39083.0000 Cap, Shroud
7. 02367.0000 Screw, Truss Head #6-32 x .62”
8. 39143.0001 Washer, Sight Gauge Tube
9. 39081.0000 Handle, Faucet, Bunn
39081.0002 Handle, Faucet, Plain Black
10. 35003.0000 Nut, Faucet Spout
11. 00601.0000 Faucet Spring
12. 29164.0000 Faucet Stem
13. 00600.0000 Faucet Seat Cup
14. 35074.0000 Screw, Hex Hd Black M4 x .7x25
15. 39080.0000 Spout, Faucet
16. 38932.0000 Cover, Drip Tray
17. 38931.1000 Drip Tray Kit (Includes item 16)
18. 26186.0000 Decal, Warning Hot Liquid
19. 39084.0000 Guard, Faucet
20. 12422.0006 Clamp, Tube .53"/.59" I.D.
21. 35342.0000 Tube, Silicone
22. 12422.0001 Clamp, Tube .59"/.66" I.D.
23. 35016.0001 Insert, Stand
24. 38929.0000 Stand, Server
25. 39617.0000 Screw, Pan Head #6-32 x .75"
26. 38930.0000 Base Plate, Stand
27. 35301.0000 Brush, Cleaning
28. 35071.0000 Decal, Black Wrap 1.5 Gal.
37974.0000 Decal, Black Wrap 1.0 Gal.
29. 35365.0000 Lid Assembly 1.5 Gal.
35365.0001 Lid Assembly 1.0 Gal.
30. 39443.0000 Pad
31. 01360.0002 Screw, Pan Head #6 x .375”
32. 38151.0000 Insert, Threaded
6
1
7
2
3
4
8
5
15
14
9
16
17
29
18
19
20
21
22
23
24
25
26
30
31
SERVER WITH BASE
35075.1 042108
P3798
32
13 12 11 10

4
REPLACEMENT PARTS
1. 39082.1000 Shroud, Sight Gauge 1.5 Gal.
(Includes Item 4)
39082.1001 Shroud, Sight Gauge 1.0 Gal.
(Includes Item 4)
2. 35010.0000 Plate, Decal Mounting
3. 35009.0000 Decal, Bunn
35009.0001 Decal, Plain Black
4. 35004.0000 Backing, Sight Gauge 1.5 Gal.
35004.0001 Backing, Sight Gauge 1.0 Gal.
5. 35005.0000 Sight Gauge Tube 1.5 Gal.
35005.0001 Sight Gauge Tube 1.0 Gal.
6. 02367.0000 Screw, Truss Head #6-32 x .62”
7. 38151.0000 Insert, Threaded
8. 39143.0001 Washer, Sight Gauge Tube
9. 39081.0000 Handle, Faucet, Bunn
39081.0002 Handle, Faucet, Plain Black
10. 35003.0000 Nut, Faucet Spout
11. 00601.0000 Faucet Spring
12. 29164.0000 Faucet Stem
13. 00600.0000 Faucet Seat Cup
14. 35074.0000 Screw, Hex Hd Black M4 x .7x25
15. 39080.0000 Spout, Faucet
16. 26186.0000 Decal, Warning Hot Liquid
17. 39084.0000 Guard, Faucet
18. 12422.0006 Clamp, Tube .53"/.59" I.D.
19. 35342.0000 Tube, Silicone
20. 12422.0001 Clamp, Tube .59"/.66" I.D.
21. 35301.0000 Brush, Cleaning
22. 35071.0000 Decal, Black Wrap 1.5 Gal.
37974.0000 Decal, Black Wrap 1.0 Gal.
23. 35365.0000 Lid Assembly 1.5 Gal.
35365.0001 Lid Assembly 1.0 Gal.
24. 39083.0000 Cap, Shroud
24
1
6
2
3
4
8
5
15
14
9
23
16
17
18
19
20
35075.1 060107
SERVER WITHOUT BASE
P3799
7
13 12 11 10

5
REPLACEMENT PARTS
- 39795.0000 Stand, Assy (Includes items 1 - 9)
1. 39449.0002 Bracket, Rear
2. 39448.0002 Bracket, Front
3. 00970.0000 Nut, Keps #8-32
4. 38929.0000 Stand, Server
5. 38930.0000 Base Plate, Stand
6. 39443.0000 Pad
7. 01360.0002 Screw, Pan Head #6 x .375”
8. 38932.0000 Cover, Drip Tray
9. 38931.1000 Drip Tray Kit (Includes item 8)
BASE FOR SERVERS WITHOUT BASE
P3868
35075.1 042108
1
4
3
5
6
7
2
8
9

6
BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY
Bunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:
1) All equipment other than as specified below: 2 years parts and 1 year labor.
2) Electronic circuit and/or control boards: parts and labor for 3 years.
3) Compressors on refrigeration equipment: 5 years parts and 1 year labor.
4) Grinding burrs on coffee grinding equipment to grind coffee to meet original factory screen sieve analysis:
parts and labor for 3 years or 30,000 pounds of coffee, whichever comes first.
These warranty periods run from the date of installation BUNN warrants that the equipment manufactured by
it will be commercially free of defects in material and workmanship existing at the time of manufacture and
appearing within the applicable warranty period. This warranty does not apply to any equipment, component or
part that was not manufactured by BUNN or that, in BUNN’s judgment, has been affected by misuse, neglect,
alteration, improper installation or operation, improper maintenance or repair, damage or casualty. This warranty is
conditioned on the Buyer 1) giving BUNN prompt notice of any claim to be made under this warranty by telephone
at [phone] or by writing to Post Office Box 3227, Springfield, Illinois 62708-3227; 2) if requested by
BUNN, shipping the defective equipment prepaid to an authorized BUNN service location; and 3) receiving prior
authorization from BUNN that the defective equipment is under warranty.
THE FOREGOING WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ANY OTHER WARRANTY, WRITTEN OR
ORAL, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF EITHER
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. The agents, dealers or employees of BUNN
are not authorized to make modifications to this warranty or to make additional warranties that are binding on
BUNN. Accordingly, statements by such individuals, whether oral or written, do not constitute warranties and
should not be relied upon.
If BUNN determines in its sole discretion that the equipment does not conform to the warranty, BUNN, at its
exclusive option while the equipment is under warranty, shall either 1) provide at no charge replacement parts
and/or labor (during the applicable parts and labor warranty periods specified above) to repair the defective
components, provided that this repair is done by a BUNN Authorized Service Representative; or 2) shall replace
the equipment or refund the purchase price for the equipment.
THE BUYER’S REMEDY AGAINST BUNN FOR THE BREACH OF ANY OBLIGATION ARISING OUT OF THE SALE OF
THIS EQUIPMENT, WHETHER DERIVED FROM WARRANTY OR OTHERWISE, SHALL BE LIMITED, AT BUNN’S
SOLE OPTION AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND.
In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales,
loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute
equipment, facilities or services, or any other special, incidental or consequential damages.
35075.1 122706