Burley d'lite Instruction Manual

Contents
Introduction 2
I. Hardware Bag Contents and Tool List 3
II. Mounting the Reflectors 3
III. Installing the Quick-Release Levers 4
IV. Attaching the Wheels 5
V. Unfolding and Folding Your Burley d’Lite 6
VI. Using the Seat Harness 11
VII. Padded Seat & Shoulder Harness,
Child Seat Recliner™, Recessed Helmet
Pocket™, and Child Seat Divider™ 13
VIII.Completing Assembly 15
IX. Hitching a Burley d’Lite to Your Bicycle 17
X. Trailer Maintenance and Care 18
XI. Safety Guidelines 19
XII. Safety Checklists 25
XIII.Parts List and Drawing 26
Warranty 28
d’Lite
Owner’s
Instruction
&
Safety
Manual

2
Burley d’Lite Owner’s Instruction and Safety Manual
Congratulations!
You’ve just purchased a Burley® trailer,the leading choice of discriminating
bicycle trailer owners worldwide.Every effort has been made to ensure your pur-
chase is of top quality and proven design,ready to provide you with many years
and miles of happy,safe trailering.
IMPORTANT: Because some of the features and guidelines for using
the Burley d’Lite merit close attention, it is very important that you
familiarizeyourselfwiththetrailerbyreadingthisentiremanualbefore
use. If you have any questions, we encourage you to contact your
authorized Burley dealer.
Introduction
Your Burley d’Lite is shipped almost completely assembled from the factory. This
manual is written sequentially to assist initial setup.You need only to:
- Install the quick-release levers
- Mount the reflectors
- Attach the wheels
- Unfold the trailer
- Install the safety flag and snap on the cover
Once you've read the safety guidelines,you're ready to go! Before trailering,
be sure you have a thorough understanding of the safety harness and of trailer
hitch operation.Practice folding and unfolding your trailer;it can easily be done
in less than a minute after practice,no tools required.Check to see that the trailer
wheels and hitch are securely attached. We again request that you read this
manual from start to finish before use,and then refer to it as necessary in the
future.
NOTE: Any reference to left or right is made in the direction of travel,
as if you were sitting in the child seat looking forward.
When Loaning or Selling Your Trailer
If you loan or sell your Burley d’Lite,supply the new user with this manual.They
must familiarize themselves with all sections—especially sections“XI.Safety
Guidelines”and“XII.Safety Checklists”prior to use.It is essential that they under-
stand the differences between riding a bicycle with a trailer and without one.It
is also essential that they understand correct wheel attachment,folding,and use
of the harness,safety flag,cover,and hitch.Always ensure that both adult and
children are wearing helmets.Never loan your trailer if it is need of maintenance
or repair.

3
Burley d’Lite Owner’s Instruction and Safety Manual
I. Hardware Bag Contents and Tool List
IMPORTANT: Please verify that you have received all of the contents
listed.Donotproceedwithassemblyifanypartsaremissing;contact
Burley immediately for replacement parts.
Hardware Bag Contents
Reflectors: Quick-Release Levers:
(2)Front reflector, clear (2) Quick-release lever
(2)Rear reflector, red
(4)Self-tapping screw, reflector
Envelope: Tools Required:
Trailer Checklist 5/16", 8mm or small adjustable wrench
Warranty Card Small, straight blade screwdriver
Burley d’Lite Owner’s Instruction & Safety Manual
II. Mounting the Reflectors
REAR REFLECTORS:
1. With the trailer side panels in
folded position locate one of the
black molded hinges (A) at the rear
trailer corner.
2. At the top of the hinge locate the
screw hole (B) and reflector locating
boss (C).Each reflector has a screw
hole (D) and a location stub (E).
3. Take a red reflector and screw it
to the hinge as shown in the figure
below.Line the reflector hole (D) up
with the hinge screw hole (B) and
the reflector stub (E) with the hinge
locating boss (C).
4. Repeat the procedure with the
second red reflector,on the other
rear trailer hinge.
A
B
D
E
C

4
Burley d’Lite Owner’s Instruction and Safety Manual
FRONT REFLECTORS:
1. Locate one of the front
tongue mounts (A). Locate
the screw hole (B) and the
locating boss (C) on the front
tongue mount. Each reflec-
tor has a screw hole (D) and a
location stub (E).
2. Position the back face of
the reflector onto the front
of the tongue mount. Line
up the tongue mount screw
hole (B) with the reflector
screw hole (D) and the reflec-
tor stub (E) with the tongue
mount locating boss (C).
3. Insert the mounting screw thought the screw hole (B) in the rear of the tongue
mount and then into the reflector screw hole (D). Tighten the screw until it is
snug. Do not overtighten.
4. Repeat for the other side of the trailer.
III. Installing the Quick-Release Levers
In the bag with the reflectors you’ll find two quick-release levers.Install these
through the hollow axle of the wheel.Make sure the lever is on the flat sideofthe
wheel,the thumb nut is on the deep-dished side,and the springs are mounted
on each side as shown in the illustration below.
The quick-release
lever must be on
flat side of wheel
and thumb nut on
deep-dished side.
This ensures that the
lever will be on the
outsidewhenwheel
is properly installed.
Deep Dish
Quick Release Lever
Thumb Nut
Flat
A
B
C
E
D

5
Burley d’Lite Owner’s Instruction and Safety Manual
IV. Attaching the Wheels
First,verify that the tires are inflated to 30–35 P.S.I.Next,tip the trailer frame on its
back end.If you are working on a rough or dirty surface,lay down a cloth or other
protective barrier to avoid damage to your trailer.Move the quick-release lever
to the unlocked position and place the wheels into the dropouts,making certain
that the axles go all the way into the slots.
IMPORTANT: Wheels are dished off-center and must be installed so
that tires are offset away from side panels, closest to outer frame.
Dished wheels are a unique feature from Burley; they create a wider
track, and thus a more stable trailer.
Once the wheels are fully seated in the dropout slots,the quick-release lever
should be positioned so that it operates in the fore and aft direction.The lever
is marked for open or closed positions.Tighten the right-hand wheel by moving
the lever from the front (open) to the rear (closed) position.Tighten the left-hand
wheel by moving the lever from the rear (open) to the front (closed) position.Use
the thumb nut to adjust for correct spacing of the quick-release lever.
When properly adjusted,you will feel resistance halfway through tightening the
lever (when the lever is pointing straight out away from the trailer).If you are
unfamiliar with the use of quick-release levers,contact your Burley dealer for a
demonstration.
Thequick-releaseleveroperatesin
fore-aft direction (with lever below
the axle). The drawing shows left-
hand wheel in the closed position.
Correct Wrong
open
closed

6
Burley d’Lite Owner’s Instruction and Safety Manual
Make sure wheels are held securely; you should not be able to rock
or shift wheels. Improperly installed wheels can fall off, causing ac-
cident and serious injury.
Only use dished, 20 x 1.75 wheels supplied with Burley d’Lite. Do not
operatewithtiresinflatedabove35P.S.I.Failuretocomplycancause
trailer tip over, resulting in accident and serious injury to cyclist or
passengers.
V. Unfolding and Folding
Your Burley d’Lite
Your Burley d’Lite is designed with a lightweight
aluminum frame,complete roll cage,and bright-
colored polyester software.Setting it up or fold-
ing it down is accomplished in a few easy steps
as follows:
Raise the Side Panels
With the trailer frame lying flat,unfold the two
side panels so that they are vertical.You will find
the roll bar lying against the left side panel.Raise
it to a horizontal position and pull it into the
right roll-bar receptacle at the top of the right
side rail.Slip the safety pin through the hole
in the roll-bar receptacle to lock the roll bar in
place.Refer to the illustration on the following
page showing the locked posi-
tion of the safety pin.Connect
the buckles at the back of
the child seat and tighten the
straps.
IMPORTANT:Alwaysfastenupper
and lower buckles behind child
seat when using trailer.

7
Burley d’Lite Owner’s Instruction and Safety Manual
Tongue Installation and Operation
The tongue is the structure that connects the trailer to the bicycle hitch. It is
designed to be removed for storage and to adjust for either trailer or stroller use.
Tip your trailer frame on its back end. If you are working on a rough or dirty
surface,lay down a cloth or other protective barrier to avoid damage to your
trailer. To insert the tongue,slide it through the front and rear tongue mounts as
shown below. Depress the safety button to allow the tongue to insert past the
front tongue mount. The safety button will spring back out once it is completely
behind the front tongue mount.
Both safety pins must be locked in place before using trailer, oth-
erwiseroll baror tonguecould shiftand causean accidentor serious
injury.
Trailer Use
For use as a trailer,line up the rearmost hole on the tongue with the hole in the
rear tongue mount. Insert the pin through both holes. Once inserted,rotate the
pin’s spring clip to engage the pin underneath the tongue mount. Always check
to ensure the tongue is properly installed before using trailer.
Front Tongue
Mount
Pin
Rear Tongue
Mount
Button
Trailer Pin
Hole
Stroller Pin
Hole
Open Locked

8
Burley d’Lite Owner’s Instruction and Safety Manual
Always check that the tongue is properly installed before each use.
Failure to do so can result in serious injury or death.
Stroller Use (requires optional Walk n’ Roller™ kit)
Your Burley d’Lite is
ready for stroller use
with the purchase
of the optionalWalk
‘n Roller™ kit from
your local bike shop.
For strolling,slide the
tongue back until the
stroller pin hole on the
tongue lines up with
the hole in the rear
tongue mount.Depress
the safety button a
second time to allow the tongue to slide past the rear tongue mount.Be sure to
replace the pin through the rear tongue mount and the tongue,and then en-
gage the pin’s clip.This option brings the stroller wheel closer to the main body
to stroller easily in tight spaces.
DO NOT attempt to attach the bicycle with the tongue in the
stroller position. There will not be adequate clearance for a bicycle
wheel.
Tongue in Trailer
position
Pin locked through
Rear Tongue Mount
and Trailer Pin hole

9
Burley d’Lite Owner’s Instruction and Safety Manual
Installation and Use of the Handle
Your Burley d’Lite comes with a two-position handle that allows for easier ma-
neuvering of the trailer when it is not attached to your bicycle. The handle is also
an important part of the optional Burley Jogger Kit ™ and the optional Walk‘n
Roller™ kit. Both of these accessories are available at your local bike shop.
The handle for the d’Lite is installed quite easily. Simply depress the buttons on
either side of the handle and slide the handle into the handle bar receivers as
shown in the illustration below. The handle is designed for either a high or low
position depending on the height and comfort of the user. This position can be
changed by flipping the handle over and installing it as described above.
Parking Brake Operation
The pre-installed parking brake on your Burley d’Lite is used to keep the trailer
stationary when you park your bike or when using the optional Burley Jogger
Kit™ or BurleyWalk‘n Roller Kit™.
To engage the brake,
move the handle to
the left.
Simply move the
handle to the right to
disengage the brake.

10
Burley d’Lite Owner’s Instruction and Safety Manual
Installing the Safety Flag
Insert the safety flag pole through the loop of ½”webbing on the outside of the
trailer and into the flag pocket at the bottom left hand corner of the trailer as
shown below. DO NOT USEYOURTRAILERWITHOUTTHE SAFETY FLAG IN PLACE.
Folding Your Burley d’Lite
Folding your Burley d’Lite is basically the reverse of unfolding it.Familiarize your-
self with unfolding the trailer as outlined above.To fold your trailer:
1. Remove the safety flag and the handle.
2. Remove the safety pin at the roll bar and discon-
nect the two buckles at the back of the child seat.
Fold the roll bar against the side panel. Fold the left
side panel first, then the right side panel.
3. Remove the wheels and store them in a safe area
with the handle.
4. Remove the safety pin at the rear tongue lock.
5. Depress the safety button and slide the tongue
out of the trailer.
We recommend reinserting the safety pins in their receptacles for storage or
transport to avoid snagging.
You can partially fold your Burley d’Lite as needed.Your options are to fold only
the side panels,remove only the tongue and hitch,remove the quick-release
wheels,or any combination of the above. Do not operate your Burley d’Lite in a
partially folded condition.

11
Burley d’Lite Owner’s Instruction and Safety Manual
VI. Using the Seat Harness
IMPORTANT: Only passengers who are able to wear a helmet and
sit upright, unassisted should ride in a child trailer. Adequate neck
strength is required to hold head upright while trailering. A physician
shouldevaluate anyonewhois ofquestionabledevelopmental age
for trailering.
Junction of Y-buckle must be positioned at child’s sternum to work
correctly.Beltsorbucklespositionednearyourchild’sneckcancause
discomfort or serious injury. Check child periodically to ensure that
he/she has not slipped from correct seated position.
Your children will ride comfortably and safely in your d’Lite with Burley’s five-
point restraint system. In addition to the safety and comfort afforded by Burley’s
restraint system,you also have the option of seating one or two passengers.
Single Passenger:
1. Unclip the center support strap (with O-ring).
2. Remove both shoulder harnesses from the
shoulder straps (see Section VII for details on
removing the shoulder harness). Unclip the
Y-buckle if necessary. Store one of the shoulder
harnesses in a safe place. Leave outboard shoul-
der straps dangling. Do not unthread the straps
from the ladder locks in this step.
3. Remove the two center shoulder straps by
unthreading them from the ladder locks.
4. Trade the position of the shoulder straps and
re-insert the straps into the ladder locks as shown
in the illustration at left. The flat parts of the male
portion of the Y-buckle should face toward the
center.
5. Install one shoulder harness assembly in the
center position as shown at above left.See Sec-
Ladder Lock

12
Burley d’Lite Owner’s Instruction and Safety Manual
tionVII for details on installing the shoulder harness.
6. Seat the child in the center of the seat.
7. Snap in the shoulder straps at theY-buckle. Ensure that theY-buckle is ad-
justed so that it is at the child’s sternum.
8. Ensure that the shoulder straps are adjusted so that the child is comfortably
kept from moving too far forward in the seat.
9. Fasten and adjust the lap belt so that it is snug.
Two Passengers
For two children,use both shoulder harnesses and two outer crotch straps.
1. Ensure that the restraint system is set up for two children so that the male
portion of each Y-buckle is facing the center of each seating position. If your
trailer was set up for single-child use,reverse the process above in the Single Pas-
senger section.
2. Attach the center support strap with O-ring.
3. Seat the first child on one side of the trailer.
4. Snap in the shoulder straps at theY-buckle. Ensure that theY-buckle is ad-
justed so that it is at the child’s sternum.
5. Ensure that the shoulder straps are adjusted so that the child is comfortably
kept from moving too far forward in the seat.
6. Repeat for the second child.
7. Fasten and adjust the lap belt so that it is snug.
Ladder Lock

13
Burley d’Lite Owner’s Instruction and Safety Manual
Child and cyclist must wear helmets when trailering. Helmets can
prevent or significantly reduce head injury in event of accident.
The straps and sliding buckles sewn to the backrest of the child seat are part
of a self-adjusting system that keeps the shoulder straps at the correct height
forchildrenofvarioussizes.Whenyoutightentheshoulderharness,thesliding
bucklesallowtheshoulderbeltstocomeacrossthetopofthechild’sshoulders,
creating a snug fit.In addition,the sliding buckles keep the straps from falling
off of the shoulders.
IMPORTANT: Always fasten and adjust the two buckles behind the
child seat when using the trailer.
VII. Padded Seat & Shoulder Harness, Child
Seat Recliner™, Recessed Helmet
Pocket™, and Child Seat Divider™
IMPORTANT: The trailer seat is intended only for children old enough
towearahelmetand sit upright by themselves unassisted. Yourchild
must have enough neck strength to hold his or her head up while
trailering.
The seat in your Burley d’Lite is designed to provide the utmost comfort for your
children. From a padded seat and shoulder harnesses to reclining the seat to
room for your children’s helmets to flow-thru mesh to keep your children cool,
the Burley d’Lite is the most comfortable trailer on the market.
Seat Pad and Shoulder Harnesses
The seat pads and shoulder harnesses in your Burley d’Lite are made of a durable
spacer weave fabric for ventilation to keep your children cool,and a high tech
foam material to provide the padding necessary for a comfortable ride. If the
seat pad and/or shoulder harnesses become dirty,they can be easily removed
and hand-washed with mild soap and water. If it is extremely hot,the seat pad
and/or harnesses can be removed to provide maximum flow-thru ventilation.

14
Burley d’Lite Owner’s Instruction and Safety Manual
Installing the seat pad and shoulder harnesses is quick and easy. Simply follow
the steps below.
Seat Pad
1) Ensure that shoulder straps and lap belt
are not in the way of the seat pad
during installation.
2) The seat platform and seat pad each
have two strips of Velcro material as shown
at right. Install the front part of the seat pad
so that the square edges of the pad face
match up with the front of the seat.
3) Attach the top part of the pad to the seat
to complete the process.
Shoulder Harness Pad
Insert the shoulder straps into the
shoulder harness pad as shown in the
drawing at right. The shoulder straps
should be oriented so that the FLAT
parts of the male buckles are facing
toward each other.
Using the Child Seat Recliner
The child seat can be reclined for added com-
fort by making the following adjustments:
• Loosen tension on lower buckle strap (A)
located behind child seat.
• Connect/tighten upper buckle strap (B),
also located behind child seat.
• For maximum recline,the lower buckle
strap (A) must be loose to allow
seat to move backward.
B
A

15
Burley d’Lite Owner’s Instruction and Safety Manual
NOTE:Foraddedsafety, always keep upper and lowerbucklestraps
fastened.
Using the Recessed Helmet Pocket
The helmet pocket on the child seat is designed to provide added room for the
back side of a child's helmet.The seatback can be modified by making the follow-
ing adjustments:
• Loosen tension on upper buckle strap (B) located behind child seat (illustra-
tion page 14).
• Connect/tighten lower buckle strap (A) located behind child seat (illustration
page 14).
The size and shape of the helmet pocket can be adjusted by adding/subtracting
tension from the upper buckle strap (B).
Using the Child Seat Divider
This feature is designed to provide additional comfort and structure to the child
seat by limiting two passengers from sliding to the center of the seat.
• Connect center crotch strap O-ring to snap hook located on the front splash
guard.
• Seat divider strap tension can be adjusted using the plastic slider on the crotch
strap.
NOTE: We recommend that the Child Seat Divider feature be used
when transporting two (2) passengers only.
VIII. Completing Assembly
At this time your trailer is nearly assembled.Snap the fabric tail gate and splash
guard to the snap studs on the side rails if you haven’t already done so.
NOTE: It’s easier to snap these when the trailer is folded; they can
remain snapped in place during folding and unfolding.

16
Burley d’Lite Owner’s Instruction and Safety Manual
Installation and Use of the Cover
Your d’Lite Big Screen 2-in-1 Cover is held in
place by six snaps at the rear and top,and front.
Always use your cover to keep debris out (and
toys inside) of the trailer when it’s in use. To
install the cover,unfold it and snap the top two
snaps first. Next,pull the cover toward the back
of the trailer and snap the two rear snaps. Finally,
using the B-tabs in front,pull the cover taut and
affixing the snaps to the front corners.
Folding and Stowing the Front Window
Folding and stowing the front window is quick and easy. Begin by unzipping the
window. Next,fold the window in half toward the back of the trailer. Then roll
the window up toward the top of the trailer. Hold the window in place by insert-
ing the elastic straps into theVelcro holders on the top of the trailer.
Using the Adjustable Sunscreen
Your Burley d’Lite is equipped with an adjustable
sunscreen to keep your kids in the shade during
bright,sunny days. To move the adjustable sun-
screen,simply pull on the tabs to move it up or
down on the trailer as necessary. If more visibility
is required,pull the sunscreen up in the middle.
This is depicted in the illustration at right.
Light Installation
To make your trailer more visible,clip a light into
the light-holder tab sewn on the upper part of the back of your cover.There are
several brands of inexpensive clip-on lights that will make your trailer more vis-
ible to motorists and other cyclists.You’re done! Please go back over these direc-
tions and recheck your work.
For increased security and safety,Burley offers a clear front and red rear LED light
package. These lights mount directly in the place of the left hand side reflectors.
See your Burley dealer for details.

17
Burley d’Lite Owner’s Instruction and Safety Manual
IMPORTANT: Read and study sections “IX. Hitching the Burley d’Lite
to Your Bicycle,” “XI. Safety Guidelines,” and “XII. Safety Checklists”
before using your Burley d’Lite.
IX. Hitching a Burley d’Lite to Your Bicycle
The trailer hitch was designed to quickly and safely attach to virtually all types of
bicycles.It is inserted in front of the left rear dropout of your bicycle.
Hitching the Trailer to Your Bicycle
1. Loosen the knob on the eyebolt until the two arms are spread fully apart.
2. Slip the lower hitch arm under the chain stay (A) and the upper arm above the
seat stay (B).
3. Wedge the hitch cone all the way back into the angle formed by the stays at the
wheel.
4. Tighten the knob until the arms are firmly clamped against the stays.Wrap the
safety strap around the inside of the chain stay,over the hitch body,and back to
the D-ring at the end of the tongue.
Make sure that the cone is wedged securely into the stays.The knob should be
finger-tight;do not overtighten.The hitch should not move,but should allow the
bicycle complete movement,including lying it down on the ground.It should
clear any racks,bags,or fittings you have on your bicycle.If there is any inter-
ference,contact your Burley dealer.
IMPORTANT: Remove trailer from your bicycle when it’s not in use to
prevent deforming the plastic hitch.
B
A

18
Burley d’Lite Owner’s Instruction and Safety Manual
Do not operate trailer without hitch safety strap properly installed. A
dangling safety strap can contact spokes and damage rear wheel
or cause accident resulting in serious injury.
Hitch must seat properly into stays and not interfere with racks, bags,
or fittings. Inspect hitch and tongue frequently for damage or loose
fasteners. Interfering parts or damaged hitch can cause accident
resulting in serious injury.
Do not use or store trailer at temperatures below 32˚Fahrenheit as
hitch rubber flex connector can become brittle and possibly break,
causing accident resulting in serious injury.
X. Trailer Maintenance and Care
Hitch and Tongue Maintenance
Your trailer is designed for low maintenance and easy care.Clean and grease the
eyebolt threads on the hitch periodically to ensure that the eyebolt knob can be
properly tightened.
Because of ultraviolet degradation,we recommend that the hitch be replaced
every five years under normal use.In sunny or smoggy locations or for trailers
that are stored outdoors,the hitch should be replaced every two to three years
for safety.Replace your hitch or tongue if there are any signs of damage—i.e.,
cracks,dents,scratches.
1. Gently remove inner cap on the end of tongue with a
medium flat-blade screwdriver.
2. Using grease gun equipped with needle type injec-
tor,squirt grease into small hole in brass bushing
until old grease flushes out ends of bushing.
3. Replace inner cap on end of tongue to protect pivot
bushing from dirt and moisture.

19
Burley d’Lite Owner’s Instruction and Safety Manual
IMPORTANT: For any spindle service other than lubrication, contact
your Burley Dealer.
Fabric Care
Your Burley d’Lite is manufactured from a tough,durable polyester.The fabric
is coated for waterproofness and is highly resistant to fading.It can be easily
cleaned with any mild soap or detergent and warm water.For more persistent
soil,use a nylon bristle brush.When not in use,store your trailer in a dry,well-ven-
tilated area;wipe it dry before storing to help avoid mildew.
Polyester fabric will eventually fade,especially when exposed to direct sunlight.
To extend the life of your fabric,as well as the hitch and other components,do
not store your trailer in direct sunlight. Do not use bleach for cleaning,as it will
damage the fabric. The fabric is an important part of your trailer’s structure,and
provides a safety envelope for child passengers. Replace any fabric that is ripped,
scuffed,or otherwise damaged.
Burley offers a durable polyester storage cover to protect your d’Lite from the
elements when it is not in use. Contact your Burley dealer for details.
Trailerwithdamagedorrippedfabriccomponentscanpermitharmful
contact between child and spinning spokes or moving pavement,
and cause serious injury. Replace damaged components.
XI. Safety Guidelines
Bicycling with a trailer is different from bicycling without one,in ways which
aren’t always obvious.It is therefore essential that you read and understand all of
the following safety guidelines—in addition to the warnings and instructions in
the previous sections—prior to using your trailer.Before loaning your trailer to
others,make sure they too understand its proper,safe use.Contact your dealer or
Burley if any of these instructions are unclear.

20
Burley d’Lite Owner’s Instruction and Safety Manual
Bicycling with a trailer, and bicycling in general, can be hazardous.
Failure to observe any of section “XI. Safety Guidelines” could result
in accident and serious injury or death.
Use Well-Maintained Bicycle and Trailer
Use a bicycle which is in good working condition,with good brakes.A frequent
safety check of your bicycle is essential.Inspect and maintain your trailer as
outlined in section“XII.Safety Checklists”of this manual.Have your Burley dealer
maintain and inspect your bicycle and trailer if you are not qualified to do so.
Loading Your Trailer
Do not overload the trailer.Maximum trailer load limit for children and/or cargo
is 100 lbs.When placing children or cargo into the trailer,keep the load centered
or forward of the axle.Pack the load as low as possible and make sure items can-
not shift around.Loose,heavy objects can injure passengers in event of a sudden
stop or tip over.
Starting and Stopping
Because of the trailer’s additional weight,a bicycle pulling a trailer will be slower
to start up and stop,and because of its length it requires more time to cross
streets or paths.Your entire vehicle is heavier and less responsive.This means you
should think further ahead in anticipating stops,turns,and starts.Note that your
trailerextendsoutfurther on the left;allowforthis differencewhen turning,pass-
ing pedestrians,or approaching obstacles (like posts on bike paths).We recom-
mend you spend some time experimenting with a loaded trailer in an uncon-
gested area to become familiar with how your heavier,longer vehicle responds.
Prevent Trailer Tip Over
Just like automobile and motorcycle trailers,bicycle trailers can tip over.To avoid
overturning:Do not pull your trailer over curbs or hit holes or other obstructions
in the road.Instruct children not to bounce,rock,or lean,which can cause a shift
of weight.Do not make high-speed turns or descents when pulling the trailer.
Always corner with caution at 5 m.p.h.or less,as the trailer cannot lean into a
turn the way a bicycle can.Do not under any circumstances travel faster than 15
m.p.h.—all road irregularities and your slowness to react are greatly magnified.