Burmester 077 User manual

1 | 76
OPERATION MANUAL
Table of contents
INTRODUCTION 3
List of Functions 6
Unpacking and setting up 8
OVERVIEW OF THE 077 11
Functional overview of the preamp front panel 12
Rear panel with internal power supply (not longer available) 13
Rear panel with external power supply 14
Functional overview of external power supply unit 15
Rear Panel 15
STARTUP AND CONNECTIONS 17
The “simple” preamp - factory settings 19
AC mains switch 26
POWER switch 26
Volume selector 26
Input selector 27
Phase reversal 27
Shifting between MAIN and REC level 27
Display brightness 27
Special functions 29
RECORD output 30
SURROUND input 30
Volume scale 31
Output amplification 31
Input sensitivity 32
Monitor lock 32
Volume balance 32
Input names 33
4 Channel Mode 33
Serial number 34
Switching off control elements of device 34
Initial volume 34
Setup menus 37
Activating the SETUP Menus 38
The Record Setup 49
The Phones Setup 52
The Phono Setup 54
The MC Setup 56
The MM Setup 57

3 | 76
2 | 76
OPERATION MANUAL
2 | 76
Introduction
Remote control and BurLink 61
Remote Control 62
BurLink 65
Connections 65
Commands 65
GENERAL INSTRUCTIONS 69
Warranty 72
Care 72
Battery hazard 72
Technical Specifications 74

5 | 76
OPERATION MANUAL 077 PREAMPLIFIER
Dear Audiophile,
Thank you for choosing this
Burmester audio component.
We sincerely appreciate your trust in our products. You have
purchased a unit, which excels in musical fidelity and combines
uncompromising manufacturing quality with technical
innovation and the highest degree of operating flexibility.
We recommend reading this user manual in its entirety before
initial operation. It will enable you to make full use of all capabilities
of this outstanding audiophile instrument. Should you have any
further questions, please contact your dealer or us directly.
Talk to us about your special requests, even if they seem out of
the ordinary. We happily accept technical reasonable challenges.
Enjoy your enhanced listening pleasure.
Your Burmester Team

7|76
6|76
OPERATION MANUAL 077 PREAMPLIFIER
List of Functions
$Phono MM module (optional), with balanced XLR 3pins inputs, input
sensitivity and input impedance are selectable; connectable subsonic
filters; automatic channel calibration for ideal channel equality
$D/A – converting module (optional), with S/P-DIF input (RCA) and USB slave
input, 069-technology with up sampling to 96kHz and 192kHz selectable
•
2 balanced output terminals, XLR 3pins, with selectable source, RECORD level
programmable for 2-Zone- Mode or TAPE-Record-Mode
• MAIN output terminals supplied with X-AMP MK2 modules
• 2 headphone terminals, audio jack 6,3mm, with selectable source and volume
preset for 2-Zone-Mode
• Global SETUP menu for individual setup of basic functions:
$Input sensitivity adjustable from -6dB to +12dB for each input allowing
better volume control
$Input names may be programmed individually
$Display of serial number adjustable
$4Channel Mode, select both levels, MAIN and RECORD as one preamp
$Device control elements can be switched off manually to eliminate operating
error (child lock)
$Reset to factory settings
• Separate SETUP-Menus for individual preset of every zone:
$Volume balance adjustable for every zone
$Start up volume adjustable for every zone
$Volume control and volume display adjustable in BURMESTER steps or dB
steps for every zone
$Output amplification for MAIN output may be selected between LOW and
HIGH to adjust to connected power amps or active loudspeakers
$Input 6for MAIN zone may be programmed as a regular input or Surround
Throughput
$RECORD output may be programmed with fixed volume for TAPE-Record-
Mode or with variable volume for 2-Zone-Mode
$Monitor lock selectable for every input during TAPE-record-Mode to
eliminate audio feedback
• Display brightness adjustable in four steps, Display-Off-Function
• Remote power up of other devices possible, Master/Slave over DC IN/OUT
connection
• BURmester LINK module for external control via RS232 and USB1.1
Through factory settings a lot of functions are disabled to operate the 077 as
a simple preamp. With the menus you are comfortably able to activate the
numerous options the 077 offers. In daily use these functions are hidden.
If wanted, factory settings can be reestablished.
The most important facts of the factory settings are:
• The output MAIN OUT is the primary output of the preamp to connect to a power
amp or active loudspeakers. This output has an adjustable volume (VARIABLE).
• The output RECORD OUT is preset as a recording output to be connected to the
input of a recording unit e.g. of an analogue tape deck. This output in factory
settings will deliver the maximum volume to the output of the selected input
(FIX).
CAUTION: Never connect a power amp or active loudspeakers to this
output in FIX mode. Serious damage to your ears and equipments may
occur.
• The Input 6/ SURROUND is supposed to be connected to the front-speakers
output of a volume adjustable surround decoder. The incoming signals on this
input will be put through to the output MAIN OUT with maximum volume
bypassing the volume control of the 077.
CAUTION: With these settings never connect a unit to this input
without a volume-control. Serious damage to your ears and equipments
may occur.
Characteristics and functions of the preamp 077:
• 6balanced input terminals, XLR 3pins. On demand operable as unbalanced
inputs by using adapter plugs.
• Surround throughput for ideal integration in home theatre systems
• Module slots for:
$Line module (standard configuration), with unbalanced inputs, RCA
$Phono MC module (optional), with balanced XLR 3pins inputs, input
sensitivity and input resistance are selectable; connectable subsonic filters;
automatic channel calibration for ideal channel equality

9|76
8|76
OPERATION MANUAL 077 PREAMPLIFIER
PLEASE NOTE:The preamplifier 077 and the external power supply unit
(if existent) are very heavy. To avoid injuries while unpacking it is
suggested that only personnel with experiences in heavy weights
unpack the units. The preamp 077 is shipped inside a plastic protective
cover. Make sure that children do not play with it to avoid the danger of
suffocation.
UNPACKING
To avoid damaging the housing, please do not use pointed or sharp tools to open
the box. Please make sure that the content of the box is complete. If something is
missing or you notice any damage while unpacking, do not hook up the unit.
Instead, contact your authorized dealer.
CONTENT OF BOXES
The two boxes should contain the following:
• 1box with the preamp 077
• 1Base plate with 4carbon fiber damping discs for the preamp
• 1AC BURMESTER power cord 2.5mm²
• 4Input adapter plugs XLR – RCA
• 1remote control 005
• 1owner’s manual
• 1box with the power supply unit (only with external power supply)
• 1Base plate with 4carbon fiber damping discs for the power supply unit
(only with external power supply)
• 1multi-pin power cord for connecting the power supply unit to the preamp
(only with external power supply)
PACKAGING
We recommend to keep the original packing in case the unit needs to be shipped in
the future.
Unpacking and setting up
SETTING UP
Too low or too high temperatures may cause damage inside of the preamp.
Therefore we recommend you leave the unit to adapt to room temperature,
before using it for the first time.
Carefully remove the unit from its packaging and set it up in an appropriate location.
To protect the preamp 077 from overheating make sure that the location offers
sufficient air circulation around the unit. Also, avoid excessive exposure to sun,
dust and humidity.
Please make sure that your desired location for the preamp is stable enough to
carry its weight.
Ventilation ducts and openings in the housing serve to keep the unit cool.
They must not be covered up with magazines, tablecloth, curtains etc.
If the preamp has to be operated in an extremely warm environment it may be
necessary to supply additional ventilation. Avoid operating the unit in an
excessively humid environment like bathrooms etc.
SET UP VARIATIONS
The feet of the preamp and of the power supply unit are constructed as spikes.
They can either be placed directly on the aluminum of the base plate or on the
supplied carbon fiber damping discs. Using the Kevlar fiber damping discs
additionally decouples the entire housing acoustically from the ground surface.
FOOT
FOOT
KEVLAR DAMPER
BASE BASE

11|76
Overview of the 077
11|76

12 13 14 15
11
1234 5 678
9 10
13|76
12|76
OPERATION MANUAL 077 PREAMPLIFIER
FUNCTIONAL OVERVIEW OF THE PREAMP FRONT PANEL
1. Input selector
2. PHASE LED lights up when phase is 180˚
between active input and output
3. AUDIO LED shows up sampling of 192kHz,
if a D/A converter module is equipped
4. Alphanumeric display shows the selected
input and the volume
5. REC/MAIN LED lights up when REC is
selected
6. Volume selector controls the playback
volume
7. POWER LED lights up red when the unit
is on
8. POWER switch to switch the unit on & off
9. Base plate
10. Foot – constructed as spike
11. PHASE/DISPLAY switch key switches the
phase and toggles display brightness
12. MODULE FUNCTION switch key functions
depend on installed module
13. IR receiver for commands of remote
control
14. RECORD/PHONES switch key
15. SETUP switch key to enter or leave
GLOBAL, RECORD and MAIN SETUP
REAR PANEL WITH INTERNAL POWER SUPPLY not longer available
17. BURLINK interface RS-232
with check LEDs
18. BURLINK interface USB with check LEDs
19. Phones jack PHONES 1
20. Phones jack PHONES 2
21. MAIN output balanced preamp output
22. RECORD output balanced output for
recording or second preamp output
23. SURROUND or high level input, INPUT 6
balanced
24. High level inputs INPUT 1 to INPUT 5,
balanced
25. Module input as ordered
26. GROUND screw for ground cable of record
player, only with PHONO modules
27. REMOTE output
28. REMOTE input
32. AC Mains Terminal
33. AC Mains Switch

15|76
14|76
OPERATION MANUAL 077 PREAMPLIFIER
16. POWER SUPPLY terminal
17. BURLINK interface RS-232
with check LEDs
18. BURLINK interface USB with check LEDs
19. Phones jack PHONES 1
20. Phones jack PHONES 2
21. MAIN output balanced preamp output
22. RECORD output balanced output for
recording or second preamp output
23. SURROUND or high level input INPUT 6,
balanced
24. High level inputs INPUT 1 to INPUT 5,
balanced
25. Module input as ordered
26. GROUND screw for ground cable of record
player, only with PHONO module
27. REMOTE output
28. REMOTE input
FUNCTIONAL OVERVIEW OF EXTERNAL POWER SUPPLY UNIT
29. Base plate
30. Foot – constructed as spike
31. POWER LED lights up red when the
unit is on
REAR PANEL
32. AC mains terminal
33. AC mains switch
34. POWER SUPPLY terminal
REAR PANEL WITH EXTERNAL POWER SUPPLY

17|76
Start-up and
connections

19|76
18|76
OPERATION MANUAL 077 PREAMPLIFIER
PLEASE NOTE:Before connecting the unit, please check if the input
voltage data on the rear panel, underneath the AC mains terminal (32)
is equal to the local voltage of your wall outlet.
In case of doubt contact a licensed electrician or your power supply
company.
• With external power supply: Connect both components with the multi-pin
power cord. To do this, plug any of the two ends (watch out for the guided grove)
of the cord carefully into the POWER SUPPLY terminal (16) of the preamp and
screw down the connector.
• With external power supply: Use the same procedure to connect the other end
into the POWER SUPPLY terminal (34) of the power supply unit.
• Connect your preferred in- and outputs of the preamp with your HiFi system.
Please refer to the chapter CONNECTIONS.
• Make sure, that the AC mains switch (33) on the rear panel of the 077 or on the
external power supply unit is set to OFF position.
• Connect the AC power cord into the AC mains terminal (32) and plug it into the
wall outlet.
• Switch the AC mains switch (33) to ON position.
• With the POWER switch (8) on the front panel the unit is switched on.
• Detailed information about the manifold functions of the preamp, are available
in the following chapters of this owner’s manual.
First Startup
THE “SIMPLE” PREAMP  FACTORY SETTINGS
All connection terminals are located on the rear panel. While connecting the
preamp, all components of the music system must be turned off.
Through factory settings a lot of functions are disabled to operate the 077 as
a simple preamp. With the menus you are comfortably able to activate the
numerous options the 077 offers. In daily use these functions are hidden.
If wanted, factory settings can be reestablished.
INPUTS
To connect source components like CD-Player, FM-Tuner, Tape deck etc. the
standard version of the preamp provides five balanced inputs (XLR) named
INPUT 1to INPUT 5(24)and one unbalanced module input (RCA) named
INPUT LINE (25). For the best sound we recommend using the balanced inputs
whenever possible.
Instead of the LINE module the preamp may be equipped alternatively with
Phono MC module, Phono MM module or with a D/A converter module.
The pinning of the balanced inputs is: PIN1=GND,PIN2=NEG, PIN3=POS.
SURROUND INPUT
The two front channels (right front / left front) of a surround sound processor or
decoder must be connected to the INPUT 6/SURR (23). In this configuration the
signal is sent directly to the MAIN outputs (not to the RECORD outputs), bypassing
volume control. Therefore connect only components with their own volume
control to the SURROUND input!
This input allows the easy integration of surround sound components into an
existing two- channel hifi system.
The SURROUND input cannot be selected over the RECORD level.
The pinning of the SURROUND input is: PIN1=GND, PIN2=NEG, PIN3=POS.
NOTICE: Never connect a unit to this input without its own volume
control. Serious damage to your ears and equipments may occur.
Connections

21|76
20|76
OPERATION MANUAL 077 PREAMPLIFIER
ADAPTER PLUGS
If your stereo components should only offer unbalanced outputs, you are able to use
our balanced inputs with the adapter plugs as unbalanced inputs. In these adapter
plugs the Pins 2 (negative input) and Pin 1 (ground pin) are connected (see graphic
below). 4 XLR- RCA adapters plugs are delivered with the units, allowing you to use
2 inputs as unbalanced inputs. If you need further plugs you may get them at your
authorized dealer.
NOTICE: Please do only use BURMESTER XLR-RCA adapter.
Wiring of the Adapter Plugs
Cinch XLR
2
1
3
MASSE
SIGNAL 3
GROUND
SIGNAL
RCA XLR
MODULE INPUT
The module input (25) may be equipped alternatively with 4different modules:
• LINE module
The standard version of the preamp is equipped with a LINE module.
In this case the module input is an unbalanced high-level input.
NOTICE: Subsequent installation of other modules must only be done by
your authorized dealer or by Burmester Audiosysteme GmbH.
• PHONO MC module
With a PHONO MC module the module input is a balanced PHONO MC input to
connect a record player with moving coil pickup (no high output MC).
If your pickup has an unbalanced output, the balanced PHONO MC input can be
converted to unbalanced mode by using XLR-RCA adapter plugs.
The input resistance and the amplification of the PHONO MC module can be
attuned to your pickup with the MC SETUP. For detailed instruction please refer
to the chapter THE SETUP MENUS / MC SETUP.
The PHONO SETUP offers an automatic channel calibration, which verifies the
channel equality of your pickup and adjusts it, if necessary. The PHONO SETUP
also offers the chance to switch on a subsonic filter to eliminate low frequency
noise.
The pinning of the balanced PHONO MC input is: PIN1=GND, PIN2=NEG,
PIN3=POS.
On request the PHONO MC modules and the adapter plugs are available at your
local dealer.
NOTICE: Subsequent installation of other modules must only be done by
your authorized dealer or by Burmester Audiosysteme GmbH.
• PHONO MM module
With a PHONO MM module the module input is a balanced PHONO MM input to
connect a record player with moving magnet pickup or high output moving
coil pickup.
If your record player has an unbalanced output, the balanced PHONO MM input
can be converted to unbalanced mode by using XLR-RCA adapter plugs.
The input capacitance and the amplification of the PHONO MM module can be
attuned to your pickup with the MM SETUP. For detailed instruction please refer
to the chapter THE SETUP MENUS / MM SETUP.
The PHONO SETUP offers an automatic channel calibration, which verifies the
channel equality of your pickup and adjusts it, if necessary. The PHONO SETUP
also offers the chance to switch on a subsonic filter to eliminate low frequency
noise.
The pinning of the balanced PHONO MM input is: PIN1=GND, PIN2=NEG,
PIN3=POS.
On request the PHONO MM modules and the adapter plugs are available at your
local dealer.
NOTICE: Subsequent installation of other modules must only be done by
your authorized dealer or by Burmester Audiosysteme GmbH.

23|76
077 PREAMPLIFIER
22|76
OPERATION MANUAL
• D/A converter module
With the D/A converter module inserted two inputs for digital audio signals will be
available: an unbalanced chinch input (RCA), which can receive pulse coded
signals (PCM) in the usual S/P-DIF format with a maximum sampling rate of
192kHz, and a USB input, which supports USB class 1 audio and USB class 2
audio, depending on the operating system of your computer. Since the USB input
is a so-called slave connection, no USB sticks or USB hard disks may be
connected.
The RCA and USB inputs are selected by either pressing the MODULE
FUNCTION (12) key on the front panel of the device or by pressing and holding
the AUDIO button on the remote control for about 2 seconds. The active input
will be indicated on the display.
The sampling rate is toggled between 96kHz and 192kHz by pushing up the
MODULE FUNCTION (12) key on the front panel of the device or by shortly
pressing the AUDIO button on the remote control. With a sampling rate of
192kHz the AUDIO LED (3) will be lit.
The level of both the RCA and USB inputs can be preset individually,
see THE SETUP MENUS / GLOBAL SETUP.
• USB Connection
To establish the connection we will describe the variants for Microsoft and
Apple operating systems.
Connecting the 077 to a Windows™ operating system for the first time will
automatically prompt the installation of the USB class 1audio driver. In the
system management of your operating system you may then select the
Burmester class 1audio output from the list of audio devices. When playing back
music over the PC now, it will be output via the 077. Regrettably problems may
occur on Windows PCs in connection with class 2audio. Therefore we
recommend selecting USB class 1audio on PCs with Microsoft operating
systems.
The Apple® operating systems automatically recognize both USB class 1audio
and USB class 2audio. To select between class 1and class 2audio, simply press
the OSD button on the remote control or the MODULE FUNCTION (12) key on
the 077 for about 2seconds. The operating system will automatically recognize
the selected connection and activate it. You may then adjust the sampling rate
between PC and 077 in the audio settings of the operating system to as high as
192kHz / 24 bit.
• USB Quality
The quality of the two USB audio classes differs in their sampling rate. The D/A
converter module of the 077 offers two options to establish a USB connection:
either as USB class 1audio or as USB class 2audio. USB class 1audio can
transmit signals of up to 96 kHz / 24 bit while class 2audio can handle signals
of up to 192kHz / 24 bit.
PLEASE NOTE: The volume level may be controlled either from the PC or
from the 077. So if the PC volume level is set to zero, the 077 will receive no
signal.
GROUNDING SCREW
When using the PHONO input as an unbalanced input for a record player it is
necessary to connect the GND wire of your record player to the GND screw (26).
Loosen the GND screw, clamp the GND wire of your turntable between the two
washers and tighten the GND screw. The GND-screw is only assembled when
a Phono module is equipped.
PLEASE NOTE:Don’t use any other tools but your hand to tighten the
GND screw! This way you avoid overwinding the screw.
MAIN OUTPUT
To connect power amps or active loudspeakers the preamp provides the
OUTPUT MAIN (21) as a regular balanced preamp output.
This output provides the volume-controlled signal of the selected input of the
MAIN level. e pinning of the OUTPUT MAIN is: PIN1=GND, PIN2=NEG, PIN3=POS.

25|76
24|76
OPERATION MANUAL 077 PREAMPLIFIER
RECORD OUTPUT
The output terminal OUTPUT REC (22) must be connected to the recording
input of an analog recording device (mostly named TAPE IN or REC).
This output provides the signal of the selected input of the RECORD level at
maximum volume level. Signals from the inputs TAPE and SURROUND cannot be
taken from the RECORD output.
Through factory settings, volume controls have no bearing on the signal at the
RECORD output.
If no recording is desired, the RECORD output may be used as a second volume
controlled preamp output. (see chapter RECORD SETUP)
The pinning of the OUTPUT REC is: PIN1=GND, PIN2=NEG, PIN3=POS.
NOTICE: Never connect a power amp or active loudspeakers to this
output with these settings. Serious damage to your ears and equipments
may occur.
HEADPHONE JACKS
The headphone jacks PHONES 1 (19) and PHONES 2 (20) require headphones
with a 6,3mm stereo plug and an impedance of 16Ωor more. Each of the phones
output can playback the MAIN and the RECORD level. The PHONES MENU gives
you the option to choose your favorite settings. The volume level is being reduced
to 01 respectively -79dB while inserting or pulling off the phones plug. With the
volume selector (6) on the front panel or with the buttons VOLUME + and.
VOLUME – on your remote control you select the volume level of the phones
outputs.
NOTICE: The signal at the MAIN or RECORD output will be interrupted
while inserting a headphone plug into the headphone jacks.
REMOTE
Connecting DC OUT (27) to the corresponding DC IN-jack of another BURMESTER-
unit offers the function to switch on or off this other unit simultaneous by the 077. In
this case, the 077 has the master function.
Connecting DC IN (28) to the corresponding DC OUT-jack of another BURMESTER-
unit offers the function to switch on or off the 077 simultaneous by the other unit. In
this case, 077 has the slave function.
BURLINK
To the BURmester-LINK interface plugs (17), (18) a computer system e.g. PC,
CRESTRONTM, AMXTM can be connected to the preamp 077. The computer system
allows a comfortable control of your High End system using for example an indivi-
dual programmable touch panel. With the LEDs beside the plugs named Tand R
(Transmit and Receive) you are able to monitor whether data exchange is working.
You will find the commands to control the 077 in the chapter BURLINK.

27|76
077 PREAMPLIFIER
26|76
OPERATION MANUAL
Operating Controls
With the exception of the AC mains switch, which is located on the rear panel of the
power supply unit, all operating controls are located on the front panel of the
preamp.
AC MAINS SWITCH
The AC mains switch (33) which completely disconnects the AC power to the unit
is located on the rear panel of the 077 or on the rear panel of the external power
supply unit above the AC mains terminal. By switching to the ON position the
standby transformer is powered up.
POWER SWITCH
The POWER switch (8) switches the preamp on and off, presuming the AC mains
switch is in the ON position.
With the POWER switch (8) set to “OFF” all functions of the preamp are powered
down. Flipping the POWER switch (8) from “OFF” to “STBY”, the POWER LED (7)
lights up orange. This shows that the unit is in standby mode.
When the POWER switch is in “STBY” position the unit can be switched on and off
by pulling up the POWER switch, pushing the POWER button on the BURMESTER
remote control, the Burlink interface or by the DC IN jack.
In operating mode (ON) the POWER LED (7) lights up red and all functions of the
preamp are activated.
PLEASE NOTE:Always switch off the preamp with the POWER switch first
before bringing the AC mains switch into OFF position.
VOLUME SELECTOR
The Volume selector (6) controls the volume level in 61 steps from 00 (mute) to 60
(maximum volume) or in dB-step from MUTE to +5dB (maximum volume with LOW
amplification) or + 21dB (maximum volume with HIGH amplification). The volume
setting can be selected separately for MAIN and RECORD level. To change between
MAIN and RECORD level pull the RECORD/PHONES switch key (14) up at the or
push the MODE button on your remote control. If the REC/MAIN LED (5) lights up,
you are controlling the RECORD level.
The selected volume level will be shown in the alphanumeric display (4).
The volume selector also controls functions in the SETUP menus.
INPUT SELECTOR
With the input selector (1) you select the input you want to listen to. The input
selection can be done separately for MAIN and RECORD level. To change between MAIN
and RECORD level push the RECORD/PHONES switch key (14) up or push the
MODE button on your remote control. If the REC/MAIN LED (5) lights up, you are
controlling the RECORD level, if it doesn’t light up you are controlling the MAIN level.
The selected input will be shown in the alphanumeric display (4) .
The input selector also controls functions in the SETUP menus.
PHASE REVERSAL
In factory settings the preamp 077 passes incoming signals without phase reversal
to the MAIN and RECORD outputs. If the pin polarity of a reproducer differs from the
pin polarity of power amps or active speakers connected to the output terminals
(see also owner `s manual PINS 2 and 3 ) there is the possibility to reverse the
phase of the according input by 180 ˚.
The phase reversal is activated or deactivated by pulling the switch key PHASE/
DI SPLAY (11) up, or by longer pressing the DIM button (approx. 2 seconds) on your
remote control. If the phase reversal is activated ( 180 ˚), the PHASE LED (2)
illuminates.
Every input needs to be preset separately for the MAIN and RECORD level.
The presetting will be maintained.
NOTICE: Please be advised that each input can be reversed separately.
A phase reversal of the outputs is not intended.
SHIFTING BETWEEN MAIN AND REC LEVEL
All presets like input selection, volume, input level, phase shift, volume display etc.
are separately selectable. Switching between MAIN and RECORD level is done by
moving the switch key RECORD/PHONES (14) upwards or by shortly pressing the
MODE button on your remote control. When the MAIN/REC LED (5) illuminates,
the device is in RECORD level. If the LED is off, the device is in MAIN level.
DISPLAY BRIGHTNESS
By pushing the switch key PHASE/DISPLAY (11) down, or by shortly pressing the
DIM button on your remote control you can adjust the brightness of your display in
four steps from “maximum brightness” to “off”.
If modus “off” is chosen, the display illuminates when the device is operated to
indicate that a function is controlled, and dims out after a few seconds.
In modus “off”, the device shifts to maximum brightness in SETUP-mode.
The display will stay illuminated until you leave the SETUP-mode.

29|76
Special Functions

31|76
077 PREAMPLIFIER
30|76
OPERATION MANUAL
The preamp 077 offers a variety of special functions in order to allow a personalized
configuration of the device. Most functions are adjustable in the SETUP MENUS.
RECORD OUTPUT
Through factory settings the OUTPUT REC (22) of the preamp 077 is preset to be
connected to an analog tape recorder. Meaning, the recording volume is fixed.
If required, this setting can be changed. The RECORD output can be programmed
as additional volume controllable preamp output. In this setting, it is possible to
provide a second room with music. The REC output is able to reproduce a different
source than the MAIN output and is volume controllable in itself.
To change the output from FIXED to VARIABLE you have to go to the RECORD
SETUP in submenu REC.
For specific instructions please refer to THE SETUP MENU/ RECORD SETUP.
SURROUND INPUT
Through factory settings the SURR/INPUT 6 (23) of the preamp 077 is preset as
a SURROUND input. The signal is transported directly to the MAIN output, avoiding
volume control and all amp stages.
If you prefer not to connect a surround decoder, you can use the input as regular
high-level input with volume control (like INPUT 1to 5). Adjustment options are
available in the MAIN SETUP in submenu M-IN6.
For specific instructions please refer to THE SETUP MENUS / MAIN SETUP.
NOTICE: In RECORD level INPUT 6is always a regular high-level
input.
Special Functions
VOLUME SCALE
Through factory settings the volume steps are set to the BURMESTER curve.
The volume indicator is divided into steps between 0 (mute) to 60 (maximum
volume).
You may change the setting to dB steps. This can be adjusted individually for the
MAIN and RECORD level.
Adjustment options are available in the MAIN SETUP in submenu M-SCALE .
The adjustment for the RECORD level can be found in the RECORD SETUP in
submenu R- SCALE .
For specific instructions please refer to THE SETUP MENUS/ MAIN SETUP
and RECORD SETUP respectively.
OUTPUT AMPLIFICATION
Through factory settings the entire volume of the preamp 077 is set to a maximum
amplification of +5dB (factor 1.8). This preset should be maintained if you are
operating your system with BURMESTER power amps, which have a high input
sensitivity. If you are operating the preamp 077 with power amps or active speakers
with low input sensitivity, it is possible to change the maximum amplification to
+21 dB (factor 11.2).
Adjustment options are available in the MAIN SETUP in submenu M-OUT.
For specific instructions please refer to THE SETUP MENUS/ MAIN SETUP.
NOTICE: The RECORD level has a maximum amplification of +5dB
(factor 1.8) when set to preamp function. The amplification of the
RECORD level cannot be adjusted.
At fixed volume the signal is put through to the RECORD output without
any influence of the preamp.

33|76
32|76
OPERATION MANUAL 077 PREAMPLIFIER
INPUT SENSITIVITY
Through factory settings all inputs are set to the same input sensitivity. As expe-
rience has shown, connected reproducers deliver different output levels. Therefore,
it is possible to decrease every input of the preamp 077 up to -6dB (factor 2) or to
increase it up to 12 dB (factor 4) in order to adjust the different volumes of your
sources.
Adjustment options are available in the GLOBAL SETUP in submenu INPUT LEVEL.
For specific instructions please refer to THE SETUP MENUS/ GLOBAL SETUP.
MONITOR LOCK
Through factory settings the OUTPUT REC (22) of the preamp 077 is preset to be
connected to an analogue tape recorder. The INPUT 3= TAPE cannot be chosen for
recording, because of the audio feedback that would result of this connection.
If your analogue recording device is connected to another input, it is possible to
activate the monitor lock for this input and lift the locking for INPUT 3.
Adjustment options are available in the RECORD SETUP in submenu LOCK.
For specific instructions please refer to THE SETUP MENU/ RECORD SETUP.
This option cannot be chosen if the volume control for the RECORD level is variable.
VOLUME BALANCE
Some spatial arrangements require shifting the volume conditions for each
reproducing channel. The volume shift is realized by reducing one of the two stereo
channels. It is possible to reduce one channel of the preamp 077 up to 9dB
(factor 2.8) in steps of 1dB, and for specific situations to switch off completely.
Adjustment options are available in the MAIN SETUP in submenu M-BAL. For the
RECORD level adjustment options are available in the RECORD SETUP in submenu
R-BAL. If the volume is fixed for the RECORD level, the balance setting has no
effect.
For specific instructions please refer to THE SETUP MENU/ MAIN SETUP and
RECORD SETUP respectively.
INPUT NAMES
Through factory settings all inputs of the preamp 077 are assigned with specific
names. You may, however label the inputs 1through 6with other names. We provide
a range of names. It is of course possible to choose an individual name, e.g. the type
of your device.
Adjustment options are available in the GLOBAL SETUP in submenu INPUT
NAMES. For specific instructions please refer to THE SETUP MENU/ GLOBAL
SETUP.
Factory setting assigns the following names:
• NPUT 1CD
• INPUT 2TUNER
• INPUT 3TAPE
• INPUT 4AUX1
• INPUT 5AUX2
• INPUT 6AUX3
• MODUL INPUT LINE (if equipped with LINE MODULE)
PH-MC (if equipped with PHONO MC MODULE)
PH-MM (if equipped with PHONO MM MODULE)
DA-RCA and DA-USB (if equipped with D/A-CONVERTER MODULE)
Restoring factory settings will reset all the input names to the ones above.
4 CHANNEL MODE
This option allows you to use both, the MAIN and RECORD level, as one
preamp. When activated only the MAIN level is operable. The RECORD level will
automatically reproduce the selected input of the MAIN level. Also the volume will
be adjusted for both levels. However you have the option to fade the volume of the
RECORD level in reverence to the MAIN level.
For the 4Channel Mode the activation option is available in the GLOBAL SETUP
in submenu 4CH-MODE.
For specific instructions please refer to THE SETUP MENUS / GLOBAL SETUP.
For the FADER option please refer to THE SETUP MENUS / MAIN SETUP

35|76
34|76
OPERATION MANUAL 077 PREAMPLIFIER
SERIAL NUMBER
In order to view the serial number of your preamp 077 after switching on the device,
the function needs to be activated.
You will find the activation options in the GLOBAL SETUP in submenu SNR.
For specific instructions please refer to THE SETUP MENUS/ GLOBAL SETUP.
SWITCHING OFF CONTROL ELEMENTS OF DEVICE
In order to prevent undesired control of the preamp 077, it is possible to lock all
controlling elements on the front panel (except the POWER switch). Then all
functions are only operable via remote control. This provides a child proof lock
option.
This option can be found in the GLOBAL SETUP in submenu FR O NT- P.
For specific instructions please refer to the SETUP MENUS/ GLOBAL SETUP.
INITIAL VOLUME
After switching on your preamp 077, a certain volume is set. It is possible to set the
volume separately for MAIN level and RECORD level.
The range of this setting extends from volume 01 and -79 dB respectively up to 20
and -60 dB respectively. If the setting LAST is chosen, the volume that was last
selected will be used. For security reasons, this is only possible up to a maximum
volume of 20 and. -60 dB respectively.
For the RECORD level this setting is only valid if the REORD level is set to adjustable
volume.
You will find the adjustment options for the MAIN level in the MAIN SETUP in
submenu M- VOL. For the RECORD level Adjustment options are available in the
RECORD SETUP in submenu R-VOL.
For specific instructions please refer to THE SETUP MENUS/ MAIN SETUP
and RECORD SETUP respectively.
The different functions of the headphones are available in the
SETUP MENU / PHONES SETUP.
The different functions of the Phono MC and Phono MM module are available in
THE SETUP MENU / PHONO SETUP, THE SETUP MENUS / MC SETUP
respectively THE SETUP MENUS / MM SETUP.

37|76
Setup Menus

39|76
38|76
OPERATION MANUAL 077 PREAMPLIFIER
The Setup Menus
The SETUP menus of the preamp 077 allow comfortable programming of certain
basic settings as well as special functions. Changes in some of the settings have an
impact on the reproduction of the signal. We recommend, selecting a moderate
volume level before activating a setup.
NOTICE: While the SETUP menu is active, the volume selector (6) on the
front panel of the 077 serves to change the settings of the various menu
items. During this procedure the volume level can only be changed by the
volume buttons on your remote control.
ACTIVATING THE SETUP MENUS
GLOBAL SETUP:
Pushing down the switch key (15) or longer pressing (approx. 2seconds) the MENU
button on your remote control activates the GLOBAL SETUP.
MAIN SETUP:
Pulling up the switch key (15) or shortly pressing the MENU button on your remote
control activates the MAIN SETUP, when the unit is in MAIN level.
RECORD SETUP:
Pulling up the switch key (15) or shortly pressing the MENU button on your remote
control activates the RECORD SETUP, when the unit is in RECORD level.
PHONES SETUP:
Pushing down the switch key (14) or longer pressing (approx. 2seconds) the MODE
button on your remote control activates the PHONES SETUP.
PHONO SETUP:
Pulling up the switch key (12) or shortly pressing the AUDIO button on your remote
control activates the PHONO SETUP.
This menu can only be activated, if a PHONO MC or PHONO MM module is equipped
and the PH-MC or PH-MM input is selected.
AS EQUIPPED:
MC SETUP:
Pushing down the switch key (12) or longer pressing (approx. 2seconds) the AUDIO
button on your remote control activates the MC SETUP.
This menu can only be activated, if a PHONO MC module is implemented and the
PH-MC input is selected.
MM SETUP:
Pushing down the switch key (12) or longer pressing (approx. 2seconds) the
AUDIO button on your remote control activates the MM SETUP.
This menu can only be activated, if a PHONO MM module is implemented and the
PH-MM input is selected.
SELECT MENU ITEM
The different items of the setup menus are selected by turning the input selector
(1) on the front panel or pressing the navigation buttons ►◄on your remote
control. (check tables on page 21)
The alphanumeric display (4) shows the selected item.
CHANGE SETTINGS
To change the setting of a selected menu item turn the volume selector (6) on the
front panel or press the navigation buttons ▲▼on your remote control.
The selected value of the menu item is indicated on the right side of the
alphanumeric display (4).
The selected value of any menu item will be saved immediately.
EXIT SETUP
Exiting the setup menu is done by pushing the same switch key that has activated
the setup or by shortly pushing the MENU button on your remote control.
The display will show SETUP SAVED!.