Burster TRANS CAL 7270 User manual

TRANS CAL 7270
www.burster.com
USER MANUAL
PORTABLE INDICATOR
FOR LOAD CELL
POWERED WITH BATTERIES
TRANS CAL 7270

TRANS CAL 7270
www.burster.com 2
INDEX
GENERAL INFORMATION
Packing content ........................................................................................................... 3
Instructions for recycling ............................................................................................... 3
General security considerations ...................................................................................... 3
Pictograms .................................................................................................................. 3
Maintenance ................................................................................................................ 4
Warranty ..................................................................................................................... 4
CE conformity............................................................................................................... 4
Environmental conditions............................................................................................... 5
Personnel ..................................................................................................................... 5
Description of the instrument......................................................................................... 6
Voltage supply.............................................................................................................. 6
Using rechargeable batteries ...................................................................................... 6/7
Using non-rechargeable batteries ................................................................................... 7
Power adaptor .............................................................................................................. 7
Mains/charging operation ............................................................................................... 8
CONTROLS and CONNECTIONS
Controls ....................................................................................................................... 8
Connections ................................................................................................................ 9
START-UP AND CONFIGURATION
Start-up ...................................................................................................................... 9
Configuration .............................................................................................................. 10
FUNCTIONS AVAILABLE BY KEYBOARD
TARE Function ............................................................................................................ 11
SPECIFICATIONS
Technical specifications ................................................................................................ 11

TRANS CAL 7270
www.burster.com 3
GENERAL INFORMATION
With the device is also supplied:
 4 X Battery 1,2V 1300 mAh NI-MH rechargeables, installed in its housing.
 Power adaptor 85-265V AC / 12V DC 600 mA.
 Sub-D male connector with cap.
 User Quick Start.
Packing content
This manual does not constitute a contractual commitment. All the information that appears in it is
subject to modifications without prior notice.
This electronic device falls within the scope of the Directive 2012/19 / EU and as such, is properly marked
with the symbol that refers to the selective collection of electrical appliances that indicates that at the end
of its useful life, you as user, you can not get rid of it as a normal urban waste.
To protect the environment and in accordance with European legislation on electrical and electronic waste
of devices placed on the market after 13.08.2005, the user can return it, at no cost, to the place where it
was purchased, so that proceed to its controlled treatment and recycling.
Instructions for recycling
General security considerations
On the TRANS CAL model 7270 devices and in this manual the risks and hazards related to safety are indicated by the
following symbols:
ATTENTION: Possibility of danger.
Read the related instructions completely when this symbol appears in order to know the nature of the
potential danger and the actions to be taken to avoid it.
Pictograms
ATTENTION: Possibility of electric shock.
Symbols on the device
NiMH rechargeable batteries
Alkaline batteries
ATTENTION ACHTUNG
Richtige Schalterstellung schützt
Vor Gerätedefeckt!
Correct switch position protects
Device from damages!
In the battery compartment there is a sliding switch. It is
very important to put the switch in the correct position to
operate with rechargeable (NiMH) or non-rechargeable
(Alkaline) batteries.
After positioning the switch, place the batteries according
to the chosen type, to avoid damage to the device.

TRANS CAL 7270
www.burster.com 4
TRANS CAL 7270 is guaranteed against any manufacturing defect or material failure for a period of
3 YEARS from the date of purchase.
In case of observing any defect or breakdown in the normal use of the instrument during the warranty
period, contact the distributor where it was purchased who will give you appropriate instructions.
This warranty can not be applied in case of misuse, connection or incorrect handling by the buyer.
The scope of this warranty is limited to the repair of the device, the manufacturer declines any other
liability that could be claimed for incidents or damages caused by the instrument's malfunction.
Warranty
Maintenance
To ensure the accuracy of the instrument, it is advisable to verify compliance with it in accordance with the
technical specifications in this manual, performing calibrations at regular time periods that will be set according to
the application criteria of each application.
The calibration or adjustment of the instrument must be done by an Accredited Laboratory or directly by the
Manufacturer.
The the equipment repair service must be carried out only by the manufacturer or by personnel authorized by the
same.
To clean the instrument, simply wipe it with a cloth soaked in neutral soapy water. DO NOT USE SOLVENTS!
CE Conformity
To obtain the declaration of conformity corresponding to this model enter our website
www.burster.com, w here said document, the technical manual and other
information of interest can be downloaded freely.
Risk of electric shock
Disconnect the TRANS CAL 7270 from the mains socket before cleaning.
DANGER

TRANS CAL 7270
www.burster.com 5
Environmental conditions
Storage:
Store at a temperature between – 20ºC y + 60ºC
The unit must be packed in clean packaging
Store in a dry environment
No condensation
Conditions of use:
The rated temperature range for the TRANS CAL 7270 is 0ºC to +40ºC
Do not switch on the instrument if it is outside this temperature range, as this may damage the instrument
Use the instrument only in an environment that lies with the specified temperature range
Note:
The following requirements must be met when operating the TRANS CAL model 7270
 Use only in enclosed spaces
 Rated temperature range between 0ºC to 40ºC
 Maximum height above sea level 2000 m
 Air humidity of 80% at up to 31ºC, decreasing linearly above that temperature to 50% at Tmax (no
condensation)
 Class of protection: 1
 Transient overvoltage category: CAT II
 Supply voltage: 4 x AA battery or 12 V DC (see pag. 6 : Voltage supply)
Restrictions on use:
The TRANS CAL 7270 does not pose a hazard if used within its specifications and in accordance with the safety
regulations
The manufacturer will not accept liability for any personal injury or property damage arising from
misinterpretation of measurement results.
Note: The TRANS CAL model 7270 is not suitable for use in the medical sector.
Personnel must be familiar with the relevant regulations. They must follow this regulations.
Only trained personnel who are familiar with the applicable safety regulations are permitted to operate the
TRANS CAL model 7270.
Personnel

TRANS CAL 7270
www.burster.com 6
The model TRANS CAL 7270 is a portable digital indicator, powered by batteries or by means of a network adapter,
which allows the user to configure it in order to be used for the following
types of input:
 LOAD CELL (mV/ V) GENERAL DATA:
Strain Gauge
Dimensions : 180 x 100 x 44 mm
Weight: 370 g
Protection type: IP41
Supply voltaje: 12 V DC
Nominal temperature range: 0ºC … 40ºC
Storage temperature range: -20ºC … 60ºC
(for further information please see “SPECIFICATIONS” on pag.11)
Description of the instrument
Voltage supply
The TRANS CAL model 7270 can be operated using batteries (rechargeable or non-rechargeable) or using a power
adapter. Switching between the two supply options for the TRANS CAL model 7270 is done purely electronically
 When the adapter supplies 12V, the battery power is disconnected and the TRANS CAL 7270 is powered
only from the mains adapter.
 When the adapter is disconnected, the power is provided by the battery pack that automatically recon-
nects.
In the battery compartment there is a sliding switch that
must be positioned according to the type of battery used
(rechargeable or non-rechargeable).
Make sure that the switch position matches the type of battery used,
to avoid damaging the device.
NOTICE
The TRANS CAL 7270 is factory equipped with rechargeable type AA batteries and the selector in the NIMH position.
Note: Before connecting the network adapter, make sure that the selector is in the correct position, otherwise
the network adapter will not charge the batteries.
Safety functions:
"Lo Bat" appears on the display w hen the supply voltage is less than 4.6 V DC
Instrument operating periods:
With the instrument connected to a full bridge load cell with 5 V DC excitation, the power required for rechargeable
batteries is around 0.5 W
Using rechargeable batteries NIMH
Use only NIMH rechargeable batteries with a capacity of 1300 mAh.
The instrument may be damaged if this recommendation is ignored.
NOTICE

TRANS CAL 7270
www.burster.com 7
Using rechargeable batteries NIMH
Power Adapter
The rechargeable batteries can be charged via the network adapter supplied with the TRANS CAL 7270.
The charge does not depend on whether the TRANS CAL 7270 is in On or OFF mode.
You can use all the measurement functions during the charging process
Note :Use only rechargeable NiMH batteries with a capacity of 1300 mAh
 The time required to charge the rechargeable batteries that can be charged by the TRANS CAL 7270 is
approximately 2,5 hours (1300 mAh capacity) when using the network adapter that is supplied with the
equipment.
 The power consumption during charging is 7.2 W
 The charging function is switched off for safety reasons if the outside temperature is outside the
range 5ºC .. 50ºC
We recommend using the following batteries::
Battery Operating time until “Lo Bat”Operating time from “Lo Bat” until switch-off
NIMH rechargeable 1300 mAh About 10 hours About 1 hour
Alkaline non-rechargeable
1500 mAh About 6 hours About 1 hour
Using non-rechargeable batteries (Alkaline)
In the battery compartment there is a sliding switch that
must be positioned according to the type of battery used
(rechargeable or non-rechargeable).
Make sure that the switch position matches the type of battery used,
to avoid damaging the device.
NOTICE
With the instrument connected to a full bridge load cell with 5 V DC excitation, the power required for non rechargeable
batteries is around 0.5 W
The instrument can be powered by a continuous voltage of 12 V or with the supplied mains adapter.
DANGER
Risk of electric shock
Inspect the power adapter for damage before use.
Do not connect the power adapter if damage is suspected.
Input voltage: 100..240 V AC
Frequency: 50/60Hz
No load power consumption: <0.3 W
Input power: 10.6 W
Output voltage: 12 V DC
Max load output current: 600 mA
Line regulation: 0.5%
Total output power: 7.2 W

TRANS CAL 7270
www.burster.com 8
Battery charge
The TRANS CAL 7270 has a tricolor LED with the legend "charge status" to indi-
cate the status of the charging process and the presence or not of the network
adapter.
The tricolor LED "charge status" is only active when the network adapter is
connected.
The meaning of the colors in the "charge status" led is:
“OFF”<> Batteries absent or faulty
“RED” <> Fast charge pending
“ORANGE”<> Fast charging
“GREEN”<> Fast charge complete
If the "charge status" LED remains off when you connect the network adapter, disconnect
the TRANS CAL 7270 and follow the instructions below to solve the problem:
 Let the TRANS CAL model 7270 cool down
 Insert the batteries with the terminals the correct way round
 Replace the batteries
ATTENTION
Controls
2
13
4
KEYS : RUN MODE PROG MODE
1<> Switch ON / OFF
2<> Set and reset TARE Increase active digit
3<> No function Shift active digit
4<> View configuration Accept the previous value
LED RG TRICOLOR:
5 <> Charge status with power adapter (approx 2,5h)
DISPLAY :
6<> Display LCD ±19999 with indication “Lo Bat”
7<> Engineering backlit unit programmable
N / kN / MN / bar / mbar / kNm / Nm / mNm
5
67
CONTROLS AND CONNECTIONS

TRANS CAL 7270
www.burster.com 9
9 <> (Supply connector 2,1 x 5,5 mm)
inside + Voltage 12 V DC
outside GND
SUPPLY CONNECTOR :
9<> 2.1 X 5.5 mm DC power plug
8 <> (Sub-D female connector)
1+ Excitation 5V , strain gauge
2N.C.
3N.C.
4N.C.
5- Excitation, strain gauge
6+ Input signal (mV)
7N.C.
8N.C.
9- Input signal (mV)
Connections
START-UP AND CONFIGURATION
Start-up
Risk of electric shock
Do not connect the TRANS CAL 7270 if it shows signs of damage caused by transport.
Use the instrument only under the conditions specified in this manual.
DANGER
In the battery compartment there is a sliding switch that must be positioned accor-
ding to the type of battery used (rechargeable or non-rechargeable).
Make sure that the switch position matches the type of battery used, to avoid damaging the de-
vice.
NOTICE
Start-up is carried out by pressing the ON key located on the front of the instrument.
A new press of this key will cause the instrument to turn off (OFF).
If the batteries are charged it can work without connecting the mains adapter, otherwise connect the mains adapter to
operate the instrument.
The network power adapter also charges the NiMH batteries, the charge is managed by an automatic circuit integrated
in the instrument, indicating its status by means of the tricolor LED "charge status" (see page 9).
After connecting the instrument with the ON key, the display performs a self-test illuminating all the segments and LEDs
of the units, then the model appears and finally the version in a sequence of 1 s for each parameter.
STRAIN GAUGE CONNECTOR :
8<> Sub-D female 9 pins
8
9

TRANS CAL 7270
www.burster.com 10
Configuration
Direct Inverse ratio
DISPLAY
DISPLAY
DISPLAY
DISPLAY
INPUT INPUT INPUT INPUT
±110nU ±120nU
±1unit
±1inP1
±10.000
±1dSP1
±10000
d.P 0
±1inP2
±10.000
±1dSP2
±10000
±1FiLt
±10000
±1Stor
RUN
mode
(5 seconds)
First step is to select the input range (±10mV or
±20mV).
Please note that the 7-segment display does not
allow to write an “m”, and that “nU” is the
alternative.
Select the range with the key and validate
with .
Changes are not saved in the memory until
you get to “Stor” at the end of the routine.
Second step is the engineering unit. The display
shows “unit” and the LED corresponding to the
current unit goes in flash.
Select desired unit with the key.
(< 1s)
(< 1s)
(< 1s)
(< 1s)
(< 1s)
After that, there is a series of five steps to program
the scaling of the display (inP1 –dSP1 –decimal
point –inP2 –dSP2).
An indication flag is shown for 1s before each step
and then, the value is presented with the first digit
in flash.
A value is programmed by using :
to change the digit value and/or the sign
to move to the next digit at right
to validate the entire value
The last step of the routine is the filtering level (FiLt).
0 means no filtering.
1 to 8 means increasing levels of a low-pass filtering
that can be chosen by use of the key.
rAnG
SCAL tEAC
After the unit, we must choose what type of
programming we want for the display.
We can choose SCAL (for scaling with input
values input) or tEAC ( to take the current value
as input value. (Never inP1 = inP2)
Enter the decimal point
position by use of the
key
Value Fc (Hz) Value Fc (Hz)
0-- 50.35
11.20 60.29
20.44 70.23
30.41 80.18
40.38