Butterfly Fitness Outdoor Table Tennis Table User manual

Fitness Outdoor
Table Tennis Table
Assembly Instructions
Safety Instructions: Children below 14 years should not assemble the table. When lowering each half of the table top, make sure
that the outer legs P6 are pulled gently outwards from the underside of the table, so far as they can go. Failure to do this may result
in injury or damage to the table. This table is suitable for indoor & outdoor use.
Make sure that the wheel brakes are off when moving the table and are on when the table is stored or in the play position.
Always cover the table when it is not in use.
STORING THE TABLE
STEP- 1
PULL OUTTHE SIDE LOCK (P23) TO LIFTTHE TABLE ON THE WHEELS.
MAKE SURE THAT LOCK (P22) IS LOCKED PROPERLYFOR STORAGE
REPEAT THE SAME FOR THE 2ND HALF.
STEP- 2
STEP- 5 STEP- 6
YOUR TABLE IS NOW READY FOR PLAY
STEP- 3
STEP- 4
REPEAT THE SAME FOR THE 2ND HALF OFTHE TABLE AS IN STEP- 1, 2 & 3
ADJUST THE HEIGHTREQUIRED WITH THE HELP OF LEVELLERS (P20)ATTACHED
ONALL 4 OUTER LEGS (P6).
NOW SLIGHTLY PULL
OUT THE SIDE
LOCK (P23) &
SLOWLY BRING
DOWN THE TABLE
ATTACH POSTS
TO THE LEFT
AND RIGHT
SIDE OF THE
TABLE.
PLACE NET ONTO
POSTS, FEED
STRING THROUGH
GROOVES.
ADJUSTTENSION
OF THE NET WITH
THE PLASTIC STRIP
Page 4
STEP- 7

1. TABLE TOP 12MM WATERPROOF BOARD- 1525×1370×12MM - 2 NOS.
2. END FRAME PIPE -1485×30×20MM - 2 NOS.
3. SIDE FRAME PIPE - 1330×30×20MM - 4 NOS.
4. INNER FRAME PIPE -1200×30×20MM - 2 NOS.
5. SMALL BACK SUPPORT PIPE- 800×19MM SQ - 4 NOS.
6. OUTER LEG - 1090×720×25×15MM - 2 NOS.
7. INNER LEG -1220×510×25×15MM - 2 NOS.
8. LONG BRACE SUPPORT - 665×25×6MM - 4 NOS.
9. WHEEL ASSEMBLY- 510×260×30×20MM - 4NOS.
10. SET OF 8 WHEELS - 50 MM WITH 2 LOCK WHEELS
11. BRACKETS FOR OUTER/INNER LEG - 75×27MM - 16 NOS.
12. BRACKETS FOR FRAME PIPE - 32MM SQ - 36 NOS.
13. LONG BACK SUPPORT PIPE - 1310×19MM SQ - 2NOS.
14. BOLTS FOR OUTER/INNER LEG 38×6MM - 8 NOS.
15. BOLTS FOR LONG BRACE SUPPORT FIXED TO OUTER/INNER LEG
- 32×6MM - 4 NOS / 38×6MM - 4 NOS.
16. BOLTS FOR SIDE LOCK ATTACHED TO OUTER LEG - 50×6MM
WITH NUT WASHERAND BHOGLI - 2NOS.
17. BOLTS FOR SIDE LOCK ATTACHED TO BRACKET - ×6MM - 2 NOS.
18. DOME NUT - 10MM- 8 NOS.
19. OUTER CORNER - 40MM - 4 NOS.
20. LEVELLERS - 25×15MM CAPSULE - 4 NOS.
21. PLASTIC CAPS FOR INNER FRAME PIPE - 20×30MM- 8 NOS.
22. CENTRE LOCK - 2 NOS.
23. SIDE LOCK - 2 NOS.
24. WHEEL ASSEMBLY CAP - 25×15MM - 8 NOS.
25. NET POST SET - 1 NOS.
26. SPARE NET - 1 NOS.
27. SCREW FOR BRACKETS ON TOP 6/95- 342 NOS.
28. SCREW FOR OUTER CORNER - 8/13 CSK- 12 NOS.
29. BOLT TO ATTACH WHEELASSEMBLY (P9) WITH INNER LEG (P7)
32×6MM - 8 NOS.
30. SPANNER - 7.5/6MM - 2 NOS.
38
PARTS LIST
P23
Page 2
P1
P25
P2
P6
P8
P9
P24
P19
P20
P10
P7
P29
P3
P11
P12
P14
P15
P13
P17
P5
P16
P18
P22
P21
P4
ADULT ASSEMBLY REQUIRED
P-29 - 32×6MM - QTY. - 8
P-30 - 7.5/6 MM - QTY. - 2 P-9 - 510×260×30×20 MM - QTY. - 4
PLEASE READ THE SAFETY INSTRUCTIONSAT THE BOTTOM OF PAGE- 4
STEP - 1
CAREFULLY LIFT THETABLE TOP HALF TO ATTACH WHEELASSEMBLY (P9) WITH INNER LEG (P7)
USING NUT & BOLT 32×6MM ANDTIGHTEN IT WITH THE HELP OF TWO SPANNERS (P30).
STEP- 2
SLIGHTLY PULL OUT THE
OUTER LEGS(P6) &
PUSH OPEN
THE TABLE SLIGHTLY BY
OPENING CENTRE
LOCK (P22).
P-29 - 6MM - QTY. - 8
Page 3