BVM GO FLY GOLD User instructions

I7100 BVM ® 2019
Length: 98”, Wing Span: 85”
Fuel Capacity: 4.8 Liters
For 160 to 200 N Turbine
ASSEMBLY AND OPERATING MANUAL
Version 1.1
November 2019
Vne 200 MPH Limit Thrust to 160 –200 Neutons
Equipped with HV Servos and should not be operated below 7.2 volts
3481 state Road 419 Winter Springs, FL. 32708 USA
tel. [phone] fax. [phone]

Ultra Bandit EVO
Assembly & Operation Manual

Ultra Bandit EVO
Assembly & Operation Manual
Table of Contents
INTRODUCTION................................................................................................................. 1
Disclaimer..........................................................................................................................1
List of BVM supplied items................................................................................................. 1
Recommended Accessories ..............................................................................................1
BVM Accessories Used in Demo Model............................................................................2
Required Tools................................................................................................................... 2
List of Adhesives/Lubricants needed .................................................................................2
List of Adhesives/Lubricants not necessarily needed.........................................................2
UNPACKING....................................................................................................................... 3
Carbon Dowel Preparation ............................................................................................... 3
INSTALLING TAIL SURFACES ......................................................................................... 4
Install the Stabs ................................................................................................................. 4
Install the vertical fin........................................................................................................... 4
WING PREPERATION AND INSTALLATION.................................................................... 5
WING TANK PREPERATION............................................................................................. 6
MOUNTING THE EZ HANGER ......................................................................................... 7
MOUNTING THE TANKS ..................................................................................................7
EQUIPMENT BOARD LAYOUT ......................................................................................... 9
...........................................................................................................................................9
Mounting the RX.............................................................................................................. 10
Mounting the Gyro ...........................................................................................................10
Wiring The Model............................................................................................................. 11
Central Control Unit.......................................................................................................... 11
FUEL SYSTEM ................................................................................................................. 12
BYPASS REMOVAL......................................................................................................... 13
BYPASS PREPARATION................................................................................................. 14
TURBINE INSTALLATION............................................................................................... 14
INSTALL ENGINE ASSESSORIES.................................................................................. 15
Mount RX and Turbine Batteries..................................................................................... 16
Flush Mount Vent and Overflow System.......................................................................... 16
Center of Gravity ............................................................................................................. 17
Control Surface Deflections and Expo Settings........................................................... 18
Connecting RX wires........................................................................................................ 18
DX18 and DX18QQ Transmitter File................................................................................ 18
First Flight Profile............................................................................................................ 19
Flight Time....................................................................................................................... 19
Taxi Test/Engine Run Up................................................................................................. 19
Takeoff............................................................................................................................. 19

Ultra Bandit EVO
Assembly & Operation Manual
Trim.................................................................................................................................. 19
Practice Approaches........................................................................................................19
Landing............................................................................................................................ 19
RX Battery Consumption..................................................................................................19

BVM ® 2019 1 11/12/2019
INTRODUCTION
Thank you for purchasing the Go Fly Ultra Bandit Evo. This model represents the latest in
manufacturing technology and completion for the R/C jet enthusiast. The factory has
expertly crafted and thoroughly inspected all aspects of the model. Only a small amount of
work is required to complete the assembly of your Bandit Evo.
This manual contains instructions for safety, operation and maintenance. It is essential to
read and follow all of the instructions and warnings in the manual.
Please read the entire manual to become familiar with the processes and procedures
before you begin to assemble your aircraft.
Disclaimer
Bob Violett Models Inc. assumes no liability for the operation and use of these products.
The owner and operator of these products should have the necessary experience and
exercise common sense. Said owner and operator must have a valid Academy of Model
Aeronautics license and a “Turbine Waiver” for operation in the U.S.A.
This is a sophisticated jet model aircraft. It must be operated with caution and common
sense and requires some basic mechanical ability. Failure to operate this product in a safe
and responsible manner could result in injury or damage to the product or other property.
Notice: Do not use with incompatible components or alter this product in any way outside
of the instructions provided by BVM, Inc. The BVM Ultra Bandit Evo has been designed
and flight tested around 160-200N class engines. Damage to the aircraft may result from
exceeding this thrust limitation.
List of BVM supplied items
Assembly and Operating Manual Package
Flush Mount Vent Fitting (#PS-SP-0301)
Central Controller Instructions
Recommended Accessories
You may have some of these products in your shop, but if not, refer to this list.
160 to 200N engine of your choice.
BVM HI FLOW U.A.T. (BVM# TA-SR-1001)
BVM Over Flow Tank (BVM# 6047)
12 Channel Power Safe Receiver
(2) 7.4v Batteries 3600 mAh RX
Safety Wire (BVM# 2800)
Bavarian Demon Aero Cortex Pro Gyro (#V-DA-BD-Cortex Pro)
ULTRA BANDIT Jet Foam Cradle (#K7300-65)
Safety Wire

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 2 11/12/2019
BVM Accessories Used in Demo Model
You may have some of these products in your shop, but if not, refer to this list.
180 Class
BVM HI FLOW U.A.T. (BVM# TA-SR-1001)
BVM Over Flow Tank (BVM# 6047)
Spektrum 12 Channel Power Safe Receiver (SPMAR12310T)
(2) 7.4v Batteries Pulse 3600 mAh RX (V-PLURX15-36002)
Bavarian Demon Aero Cortex Pro Gyro (#V-DA-BD-Cortex Pro)
Required Tools
A combination of Metric and SAE hex socket and drivers along with a small standard and Phillips
head drivers will be necessary.
9/64” Long Ball Driver (PS-TO-0008)
List of Adhesives/Lubricants needed
Available at BVMJets.com
Super O-Lube BVM #5779
Axle Super Lube BVM #5784
Dry Lube BVM# 1947
Pacer Z-42 # PT42
List of Adhesives/Lubricants not necessarily needed
Available at BVMJets.com
BVM Aeropoxy # 9566
BVM Qt Poxy # PA-SR-0042
Zap-A-Goo # PT12
BVM Thin Lube for “O” Rings BVM# 1945

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 3 11/12/2019
UNPACKING
Carefully remove items from the box. Open each package and inspect for shipping
damage. After reading this entire manual, get familiar with the major kit components.
Note: Damaged parts must be reported to BVM within 7 days of receiving your kit.
Become familiar with the work completed at the factory. It is important that you inspect and
approve this work now.
Using a stand, such as the BVM Ultra Bandit Jet Foam Cradle (K7300-65) will aid in the
assembly of the Ultra Bandit Evo.
Carbon Dowel Preparation
Use BVM Dry Lube (BVM# 1947) on the
Carbon Rods to allow easier installation
into the wing and tail receptacles.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 4 11/12/2019
INSTALLING TAIL SURFACES
Install the Stabs
Connect the servo leads and secure
with servo clips or tape.
Insert the Carbon Rods fully into the
receiver brackets.
Secure each stab by tightening the
bolts with a 9/64 ball wrench.
Install the vertical fin
Connect the servo leads and secure
with servo clips or tape.
Insert the Carbon Rods into the
receivers.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 5 11/12/2019
Secure the vertical fin by tightening
the clamps bolts with a 9/64 ball
wrench.
WING PREPERATION AND
INSTALLATION
Lubricate the O’Rings with Super O-
Lube (BVM# 5779).
Lubricate the axles with Super Lube
(BVM# 5784).

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 6 11/12/2019
Connect the servo leads and secure
with servo clips or tape.
Insert the Carbon Rods into the
receivers.
Secure each wing by tightening the
(2) clamp bolts with a 9/64 ball
wrench. Front Carbon Dowel only.
WING TANK PREPERATION
Your Wing Tanks have a ¼” Dowel in
the front. A ply tab in the rear and the
EZ Hanger in the middle.
Using a Dremel make the hole in front
so the dowel can slide through the
fiberglass. The structure below
already has a hole for the dowel to sit
in. When this is done slot the rear of
the tank to accept the ply tab. These
can be glued into place using thick
CA glue.
Note a small bevel on the dowel will help when installing the tanks on the wings.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 7 11/12/2019
MOUNTING THE EZ HANGER
The EZ Hanger is mounted to the
tank using 2 #4 counter sunk wood
screws. The tank has 2 predrilled
holes where it mounts.
NOTE: There are 2 longer 4-40 bolts
that come with the EZ Hanger. These
will get used in the next step.
Once the EZ Hanger is on the
tank, remove the 4-40 bolt from
the collar. Using your Dremel
make a slot on the inside of the
tank, use the longer 4-40 bolt to
extend through the side of the
tank and into the collar. This is
what will remove your tank.
MOUNTING THE TANKS
Using the cardstock supplied cut out the card tool
to fit around the carbon flex plate. Tape the
template to the wing. Using the drill sizes on the
template drill the wing accordingly.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 8 11/12/2019
With the template still on the wing mark the
slot at the rear of the template and slot the
wing with a 1/8 carbide cutter.
The center hole gets tapped for a 10-32 stud.
This is what holds your tank to the wing.
NOTE: A small drop of thin CA will harden the
threads and put tension on the stud.
When done it will look like this.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 9 11/12/2019
EQUIPMENT BOARD LAYOUT
CENTRAL
CONTROLLER
AIR VALVES
Air Fill Valve
Gray- Brake
Blue- Gear Up
Red- Gear Down
White- Door Open
Black-Door Close

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 10 11/12/2019
Mounting the RX
Mount your receiver in the following
location.
NOTE: Follow your radio manufacture
recommendations for RX mounting.
You can install the Receivers ON/OFF
switch in the provided mount and install it in
a location easiest for you.
Mounting the Gyro
Use the space aft of the Receiver to mount
the Gyro of your choice. Use the 2-sided
adhesive tape provided by the Gyro
manufacture to adhere the gyro in place.
Follow the manufacture guidelines to
connect to the receiver.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 11 11/12/2019
Wiring The Model
Central Control Unit
Follow the instruction in the Central Control
Unit Manual that was provided along with
this manual.
NOTE: This has been programmed to
Failsafe at 35 PSI.
Servo Wire Color Codes
Throttle
NA
Rudder
Blue
Elevator
Left
Green
Elevator
Right
Purple
Aileron
Left
Orange
Aileron
Right
Yellow
Flap
Left
Brown
Flap
Right
Grey
Brake
Red/White
Steering
Black

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 12 11/12/2019
FUEL SYSTEM
The fuel system is factory installed. Please read the
“Go Fly Fuel System Check” article supplied with your
manual package.
Both Main Tanks and Header tank are shown.
NOTE: We use Safety Wire inside the tanks to secure
fittings and we use Spring Clamps on the outside.
This has been done for you.
Your Bandit will have a factory
installed UAT Mount that also holds
the Pump and ECU.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 13 11/12/2019
BYPASS REMOVAL
Remove the Bypass by removing the (2)
440x 3/8 SHCS that secure the tailpipe to
the bypass.
Slide the Tailpipe towards the aft of the
fuselage.
Remove the (4) SHCS outside holding the
cover down.
Remove the (4) #2 SHCS inside the
bypass.
NOTE: You can radius the ByPass to allow
clearance of the starter motor.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 14 11/12/2019
BYPASS PREPARATION
Tape off and scuff the aft inside portion of
the bypass
Apply (3) coats of BVM Heat Shield to the
inside of the bypass.
Note: A heat gun can be used to speed up
the drying process in between coats.
Install the bypass, Turbine and tailpipe.
TURBINE INSTALLATION
Sight down the tailpipe to ensure the turbine is
centered
Mark the location of the turbine mounting holes
and use your favorite mounting hardware.
NOTE: Our Demo Model use’s 4 SHCS and washer
for mounting.

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 15 11/12/2019
On some mounts it may be necessary to drill
new holes to clear engine rails.
NOTE: You can also notch the rails to fit.
New mounting holes for the KingTech K-210
strap.
INSTALL ENGINE ASSESSORIES
Mount the ECU and Fuel Pump on the
Equipment Board just forward of the
intakes. The ECU battery is mounted on
the tray in the nose area.
NOTE: Here are a few examples.
KingTech Installation
JetCat Installation

Ultra Bandit EVO
Assembly & Operation Manual
BVM ® 2019 16 11/12/2019
Mount RX and Turbine Batteries
RX Batteries and ECU Battery shown
mounted.
NOTE: Woods parts have a catalyzed sealer
on them.
The BVM Demo Model balances with this
configuration and 6 ounces of ballast.
Flush Mount Vent and Overflow System
A flush mounted vent system is used on
the fuel system. A magnetic vent plug
with red “Remove Before Flight” tag and
BVM Overflow/Taxi tank conversion
fittings are provided. (Tank not included)
Install the fittings to your overflow/taxi
tank. Use an overflow tank while fueling
to prevent spillage and to ensure fuel
tanks are full before flight.
Use BVM Overflow tank Part #BVM6047