BWI Eagle AIR-EAGLE 38-2000-VBR-AC Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®SR
2.4 GHz RF Receiver
MODEL 38-2000-VBR-AC
DESCRIPTION
The AIR-EAGLE SRis an RF system designed for short to medium range
wireless remote control of electricalapparatus in avariety of industrial
applications. Systems can consist of any number of receivers and
handheld or contact input transmitters working together.This receiver is
equipped with 4 independent relays that can switch 5 amps @ 120VAC or
30VDC. The relays are user programmablefor momentary or
toggle/latching operation andcan be directly interfaced with the
customer's equipment or P.L.C. Eight userselectable frequencies allow
multiple systems to be used inthe same area. Capable of receiving
remote signals transmitted from up to 600 feet away, the Air-Eagle SR
Receiver utilizes spread-spectrum technology and provides the utmost in
security and reliability.
MODEL NOTES
This receiver was designed specifically to communicate with the “36”
series “VBR” transmitters and features a confirmation signal that is sent
back to the transmitter causing it to vibrate when its transmission has
been received.
INSTALLATION
DISCONNECT Power from all equipment before installation.
1. Mount the receiver in a convenient location.
2. Install relay control wiring to the terminal strip.
3. Attach rubber duck antenna or coax from external antennato
connector on side of enclosure.
4. Connect supplied power input cable to your external power source.
TERMINAL STRIP WIRING (TER1)
Terminal 1
100-250 VAC Power Input
Terminal 2
100-250 VAC Power Input
Terminal 3
CH1 Dry Contact Input (Common)
Not used on
this model
Terminal 4
CH1 Dry Contact Input
Terminal 5
CH2 Dry Contact Input (Common)
Terminal 6
CH2 Dry Contact Input
Terminal 7
N/O Relay 1
Terminal 8
C Relay 1
Terminal 9
N/C Relay 1
Terminal 10
N/O Relay 2
Terminal 11
C Relay 2
Terminal 12
N/C Relay 2
Terminal 13
N/O Relay 3
Terminal 14
C Relay 3
Terminal 15
N/C Relay 3
Terminal 16
N/O Relay 4
Terminal 17
C Relay 4
Terminal 18
N/C Relay 4
CONTROLS & INDICATORS
POWER/TX
LED1
Dual color LED. Illuminates red while receiver is
booting up; changes to green when boot-up is
successful and unit is ready to operate. If this LED
fails to turn green, power unit off for 15-20
seconds, then reapply power.
LED2
Illuminates green while relay 1 is energized
LED3
Illuminates green while relay 2 is energized
LED4
Illuminates green while relay 3 is energized
LED5
Illuminates green while relay 4 is energized
REL1 –REL4
Four SPDT output control relays
RF1
RF Module that transmits/receives data

AIR-EAGLE®SR
2.4 GHz RF Receiver
MODEL 38-2000-VBR-AC
RELAY & FREQUENCY SET-UP
The unit is shipped from the factory with SEL1 switches in the open
positions. All four relays will operate as maintained momentary and unit is
receiving commands on frequency one. If you wish to change these
default settings, followthe instructions onthe table below.
1) Remove power from unit
2) Remove top cover.
3) Select desired relay operation and/or network frequency using table
below.
4) Reattach cover and apply power.
5) Programming is now complete.
RELAY CONFIGURATION
SEL1
SWITCH
NUMBER
OPEN
CLOSED
SW1
Relay #1 momentary (default)
Relay #1 toggle/latch
SW2
Relay #2 momentary (default)
Relay #2 toggle/latch
SW3
Relay #3 momentary (default)
Relay #3 toggle/latch
SW4
Relay #4 momentary (default)
Relay #4 toggle/latch
Maintained Momentary –Relay mimics button or input –when
depressed or closed, relay will be energized; when released, relay de-
energizes
Toggle Latch –Relay changes (and holds) its state each time the
corresponding button or input is depressed or closed.
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
SW8& SW9 Not used on this model
SPECIFICATIONS
Power Supply
100-250 VAC, 5 W, 50/60 Hz
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC per
channel
Fuse Protected
1 amp
Receiver Frequency
2.4 GHz Spread Spectrum
Receiver Range
Up to 600feet
Note: Range figures are estimates, based on free-air terrain with limited sources of
interference. Actual range will vary based on transmitting power, orientation of transmitter
and receiver, height of transmitting antenna, height of receiving antenna, weather
conditions, interference sources in the area, and terrain between receiver and transmitter,
including, but not limited to, indoor and outdoor structures such as walls, metal objects,
trees, buildings, hills, and mountains.
Receiver Channels
Eight independent network frequencies
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate, IP66 (NEMA 4)
Weight
Approx 2.11 lbs.
APPROVALS
United States (FCC)
MCQ-XBEE3
Canada (IC)
1846A-XBEE3
Europe (CE)
ETSI
Australia
RCM
Brazil
ANATEL 06329-18-01209
ACCESSORIES
Standard Antenna (Included):
2.4GHz TNC “Rubber Duck” Antenna
49-1201
Mobile/Base Antennas –
Used to help achieve max range in both non line of sight and line
of sight applications. - Contact BWI Eagle for recommendations
2.4GHz Thru-Hole Mount Mobile Antenna
49-2201
2.4GHz Magnet Mount Mobile Antenna
49-2202
2.4GHz Omni Directional Base Antenna
49-3201
2.4GHz Yagi Directional Base Antenna
49-3202
High Quality Coax Cables –
Used to connect external high gain antennas to control unit
Flex Coax Cable w/Connectors –Available in
5’,15’,25’,30’,40’,60’,80’,100’ Lengths
49-4000-XX
(XX = # of
Feet)
Bulkhead Extensions –
Used to provide an external antenna connection whenmounting
control unit inside another enclosure
TNC Male to TNCBulkhead Cable Assembly -
Available in 2’, 4’, 7’ Lengths
49-5004-X-ISO
(X = # of Feet)
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants theAir-Eagle Remote Control System, if properly
used and installed, will be free from defects inmaterial and workmanship
for a period of 1 year after date of purchase. Said warranty to include the
repair or replacement of defective equipment. This warranty does not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair,improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist
under state law, apply only to the original purchaser of the equipment, and
last only for as long as such purchaser continues to owntheequipment.
This warranty replaces all other warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWI Eagle makes no express warranties beyond
thosestated here. BWI disclaims without limitation, implied warranties of
merchantability and fitness for a particular purpose. Some jurisdictions do
not allowthe exclusion of implied warranties so this limitation may not
apply to you. To obtain warranty service, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss duringshipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 3/7/2022 / PRODUCT REV. 10
105 Bonnie Drive
Butler, PA 16002
[phone]
Fax [phone]
www.bwieagle.com