BWI Eagle AIR-EAGLE SR 38-2020 Manual

PRODUCT INFORMATION
BULLETIN
238 Pillow Street
Butler, PA 16001
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®SR
2.4 GHz RF Receiver
MODEL 38-2020
DESCRIPTION & GENERAL OPERATION
The AIR-EAGLE SRis an RF system designed for short-range wireless
remote control of electrical apparatus in a variety of industrial applications.
This receiver is designed to operate with the model 38-1320 Air-Eagle SR
Transmitter. Relays 1 and 2 are fail-safenormallyclosed relays that will
energize when 120VAC power is applied to the unit. Relay 1 will stay
energized as long as the transmitter is communicating withthe receiver.
If the Stop button on the transmitter is depressed, Relay 1 will
momentarily de-energize. Relay 1 will also de-energize after a one minute
loss of communication between the transmitter andreceiver. Both Relays
1 and 2 willde-energize if 120VAC power is lost at the receiver. Relays 3
and 4 are not used on this model.
APPROVALS
United States (FCC) OUR-XBEEPRO
Canada (IC) 4214A-XBEEPRO
Europe (CE) ETSI
INSTALLATION
DISCONNECT AC Power from all equipment before installation.
1. Mount the AIR-EAGLE SR RECEIVER in a convenient location.
2. Install antenna. The unit has an antenna connector located on the
rightside on the enclosure.Attach the suppliedportable antenna to
this connector.
3. ConnectAC power and control tothe proper terminals in your control
circuit.
TERMINAL STRIP WIRING
1 N/O Relay #1 7 N/O Relay #3 13 120 VAC - (Neutral)
2 C Relay #1 8 C Relay #3 14 120 VAC - (Hot)
3 N/C Relay #1 9 N/C Relay#3
4 N/O Relay #2 10 N/O Relay #4
5 C Relay #2 11 C Relay #4
6 N/C Relay#2 12 N/C Relay#4
Dimensions (withmounting plate) 6.3” L x 4.8” W x 2.3” H
CONTROLS AND INDICATORS
TER1
D6
R11
D7
D3
R3
VR1
D2
MOV1
F1
BP1
BP2
MOV2
REL1
MOV3 MOV4
+
C3
FET3
+
+
INPUT OUT
--
PWR1
D1
R10
C1
C2
FET2
RF1
R9
D4
R8
R4
R5
R2
SEL1
D5
FET1
R6
FET4
LED1
R7
IC1
T1
R1
LED4LED3 REL4REL3 LED2
REL2
3.3V
N/O C N/C
- +
||
1 2
|
|| | | |
N/O C N/C 43
AC/DC INPUT
N/O C N/C N/O C N/C
.
LED1 Illuminates when relay #1 is energized
LED2 Illuminates when relay #2 is energized
LED3 Not used on this model
LED4 Not used on this model
RF1 RFmodule thatreceives data from theremote
transmitter
REL1 thru REL4 Four SPDT output control relays
SEL1 Seven dip switches for selecting relay options
and operating frequency

AIR-EAGLE®SR
2.4 GHz RF Receiver
MODEL 38-2020
RELAY & FREQUENCY SET-UP
The unit is shipped from the factory with SEL1 switches in the open
positions. All four relays will operate as maintained momentary and unit is
receiving commands on frequency one. If you wish to change these
default settings,follow the instructions on the table below.
RELAY CONFIGURATION
SEL1
SWITCH
NUMBER OPEN CLOSED
"1" N/A N/A
"2" N/A N/A
"3" N/A N/A
"4" N/A N/A
FREQUENCY SET-UP
Frequency
Selection SEL1 –
SWITCH NUMBER
“5”
SEL1 –
SWITCH NUMBER
“6”
1 OPEN OPEN
2 CLOSED OPEN
3 OPEN CLOSED
4 CLOSED CLOSED
OTHER
SEL1
SWITCH
NUMBER
“7”
Reserved for future use
SPECIFICATIONS
AC Input 120 VAC, 16 W, 50/60 Hz
Relay Contacts SPDT 5 amp @ 120VAC per channel
Fuse Protected 1 amp
Transceiver Frequency 2.4 GHzSpread Spectrum
Receiver Range Approximately 300 feet
Receiver Channels Four independentnetworks
Enclosure Polycarbonate /NEMA 4, 4x, 12+ 13
Operating Temperature -40oF to +185oF
REPLACEMENT PARTS & ACCESSORIES
PC Board 38-2022
2.4GHz Rt. Angle TNC Rubber Duck Antenna 99-ANT-0004
Air-Eagle SR Transmitter 38-1320
Optional Antennas/Accessories:
2.4GHz TNC Portable Antenna 49-1201
2.4GHz Mobile Magnetic Mount Antenna 49-2201
2 Ft. Bulkhead Assembly (Used whenmounting
receive inside another enclosure) 49-5004
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly
used and installed, will be free from defects in materialand workmanship
for a period of 1 year after date ofpurchase. Saidwarranty to include the
repair or replacement of defective equipment. This warrantydoes not
cover damage due to external causes, including accident, problems with
electrical power, usage not in accordance with product instructions,
misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, and anyimplied warranties that mayexist
under state law, applyonlyto the originalpurchaser of the equipment,and
last only for as long as such purchaser continues to own the equipment.
This warrantyreplaces allother warranties, express or implied including,
but not limited to, the implied warranties or merchantability and fitness for
a particular purpose. BWIEagle makes no express warranties beyond
thosestated here. BWI disclaims without limitation, implied warranties of
merchantability and fitnessfor a particular purpose. Some jurisdictions do
not allow the exclusion of implied warranties so this limitation may not
apply to you. To obtain warrantyservice, contact BWI Eagle for a return
material authorization. When returning equipment to BWI Eagle, the
customer assumes the risk of damage or loss during shipping and is
responsible for the shipping costs incurred.
DOCUMENT DATE: 22-Mar-06
238 Pillow Street
Butler, PA 16001
[phone]
Fax [phone]
www.bwieagle.com