BWI Eagle AIR-EAGLE SR PLUS 38AN-5-0003-120VAC Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®SR PLUS
Analog & Digital 2.4 GHz RF Receiver
MODEL 38AN/DP-5-0003-120VAC
DESCRIPTION
The AIR-EAGLE SR,MODEL 38AN/DP-5-0003-120VAC Is an RF receiver
equipped with one analog output and one relay output. It is designed to
work with the handheld transmitter model 36UP-HHED-4-001 for both
“On/Off” and “Speed” control. This unit capable of receiving commands
from up to 600 feet away. Eight network frequencies to allow multiple
systems to operate simultaneously in the same area without
interference.
INSTALLATION
1. Mount the AIR-EAGLE SR RECEIVER in a convenient location
2. Install wiring to terminal strip.
3. Install antenna onto TNC connector onside of unit.
4. Plug supplied AC-DC wall plug adapter into 120VAC outlet.
TERMINAL STRIP WIRING
TER1 (LEFT BLOCK)
TER2 (RIGHT BLOCK)
1
(-) 12VDC*
1
Analog Output (-)
2
(+) 12VDC*
2
(+) Current Output
*From supplied 120VAC
wall plug adapter
3
(+) Voltage Output
4
N/O Relay
5
C Relay
6
N/C Relay
7
N/O Relay –2nd Pole
8
C Relay –2nd Pole
9
N/C Relay –2nd Pole
10
Open Drain Output (not used)
Note #1 –Output type MUST be selected for the terminal strip wiring to
take effect! (See OUTPUT OPTIONS & FREQUENCY SET-UP)
Dimensions (with mounting plate) 6.3” L x 4.8” W x 2.3” H
CONTROLS & INDICATORS
POWER LED
Illuminates GREEN when powered on
OUTPUT
FAULT LED
Used in 4-20mA mode only –Illuminates RED when
current loop open

AIR-EAGLE®SR PLUS
Analog & Digital 2.4 GHz RF Receiver
MODEL 38AN/DP-5-0003-120VAC
OUTPUT OPTIONS & FREQUENCY SET-UP
This receiver is factory set with an analog output of 0-24mA selected and
to operate onfrequency #1. If you wish to change the default settings,
follow the instructions using the table below:
1) Remove power from unit
2) Remove top cover.
3) Select desired output option and/or frequency using table below.
4) Reattach cover and apply power.
5) Programming is now complete.
OUTPUT CONFIGURATION
SEL1
SW1 & 2
OUTPUT TYPE
SW1
SW2
0-24mA Output (default)
TER2 Pins 1 and 2
OPEN
OPEN
0-20mA Output
TER2 Pins 1 and 2
CLOSED
OPEN
4-20mA Output
TER2 Pins 1 and 2
OPEN
CLOSED
Voltage Output
TER2 Pins 1 and 3
CLOSED
CLOSED
SEL1
SW3
VOLTAGE TYPE
OPEN
CLOSED
SW3
0-10V Output (default)
0-5VDC Output
Note –SW3 is only to be used if running in “voltage mode”
SEL1
SW4
ANALOG MEMORY
OPEN
CLOSED
SW4
Analog output at 0% at
power up (default)
Power on with previous
analog setting
NOTE: Analog output must stay at a level for 30 seconds before it is
saved.
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
APPROVALS
United States (FCC)
OUR-XBEEPRO
Canada (IC)
4214A-XBEEPRO
Europe (CE)
ETSI
SPECIFICATIONS
Outputs
One 4-20mA or voltage output (0-5 or 0-10 VDC)
One DPDT2amps @120VAC or 30VDC relay output
Fuse Protected
2 amp slow-blow
Safety Timer
15 seconds
AC Input
100-240 VAC, 16 W, 50/60 Hz from
supplied wall adapter
Enclosure
Polycarbonate NEMA 4 (IP66)
Frequency
2.4 GHz Spread Spectrum
8 Independent Networks
Reception Range
Up to 600 Feet
Note: Max range figures are estimates, based on free-air terrain with limited sources of
interference. Actual range will vary based on transmitting power, orientation of
transmitter and receiver, height of transmitting antenna, height of receiving antenna,
weather conditions, interference sources in the area, and terrain between receiver and
transmitter, including, but not limited to, indoor and outdoor structures such as walls,
metal objects, trees, buildings, hills, and mountains.
Operating Temperature
-40oF to +185oF
ACCESSORIES
Standard Antenna (Included):
2.4GHz TNC “Rubber Duck” Antenna
49-1201
Mobile/Base Antennas –
Used to help achieve max range in both non line of sight and line
of sight applications. - Contact BWI Eagle for recommendations
2.4GHz Thru-Hole Mount Mobile Antenna
49-2201
2.4GHz Magnet Mount Mobile Antenna
49-2202
2.4GHz Omni Directional Base Antenna
49-3201
2.4GHz Yagi Directional Base Antenna
49-3202
High Quality Coax Cables –
Used to connect external high gain antennas to control unit
Flex Coax Cable w/Connectors –Available in
5’,15’,25’,30’,40’,60’,80’,100’ Lengths
49-4000-XX
(XX = # of
Feet)
Bulkhead Extensions –
Used to provide an external antenna connection when mounting
control unit inside another enclosure
TNC Male to TNCBulkhead CableAssembly -
Available in 2’, 4’, 7’ Lengths
49-5004-X-ISO
(X = # of Feet)
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and
installed, will be free from defects in material and workmanship fora period of 1 year
after date of purchase. Said warranty to include the repair or replacement of defective
equipment. This warranty does not cover damage due to external causes, including
accident, problems with electrical power, usage not in accordance with product
instructions, misuse, neglect, alteration, repair, improper installation, or improper
testing. This limited warranty, and any implied warranties that may exist under state
law, apply only to the original purchaser of the equipment, and last only for as long as
such purchasercontinues to own the equipment. This warranty replaces all other
warranties, express or implied including, but not limited to, the implied warranties or
merchantability and fitness for a particular purpose. BWI Eagle makes no express
warranties beyond those stated here. BWI disclaims without limitation, implied
warranties of merchantability and fitness for a particular purpose. Some jurisdictions
do not allow the exclusion of implied warranties so this limitation may not apply to
you. To obtain warranty service, contact BWI Eagle for a return material
authorization. When returning equipment to BWI Eagle, the customer assumes the
risk of damage or loss during shipping and is responsible for the shipping costs
incurred.
DOCUMENT DATE: 09/20/2021 / PRODUCT REV.3