BWI Eagle AIR-EAGLE SR 38-5000-AC Manual

PRODUCT INFORMATION
BULLETIN
105 Bonnie Drive
Butler, PA 16002
724-283-4681
724-283-5939 (fax)
www.bwieagle.com
AIR-EAGLE®SR
2.4 GHz RF Receiver
MODEL 38-5000-AC
DESCRIPTION
The AIR-EAGLE SRis an RF system designed for short to medium range
wireless remote control of electricalapparatus in avariety of industrial
applications. Systems can consist of any number of receivers and
handheld or contact input transmitters working together.This receiver is
equipped with 4 independent relays that can switch 5 amps @ 120VAC or
30VDC. The relays are user programmablefor momentary or
toggle/latching operation andcan be directly interfaced with the
customer's equipment or P.L.C. Sixteen user-selectable digital addresses
and eight user selectable frequencies allow multiplesystems to be used in
thesame area. Capable of receiving remote signals transmitted from up to
600 feet away, the Air-EagleSR Receiver utilizes spread-spectrum
technology and provides the utmost insecurity and reliability.
INSTALLATION
1. Mount the AIR-EAGLE SR RECEIVERIN a convenient location.
2. Install relay control wiring to the terminal strip.
3. Attach rubber duck antenna or coax from external antennato
connector on side of enclosure.
4. Connect supplied power input cable to your external power source.
Make the following connections on the PC Board Terminal Strip (TER1)
TERMINAL STRIP WIRING (TER1)
Terminal 1
100-250 VAC Power Input
Terminal 2
100-250 VAC Power Input
Terminal 3
CH1 Dry Contact Input (Common)
Not used on
this model
Terminal 4
CH1 Dry Contact Input
Terminal 5
CH2 Dry Contact Input (Common)
Terminal 6
CH2 Dry Contact Input
Terminal 7
N/O Relay 1
Terminal 8
C Relay 1
Terminal 9
N/C Relay 1
Terminal 10
N/O Relay 2
Terminal 11
C Relay 2
Terminal 12
N/C Relay 2
Terminal 13
N/O Relay 3
Terminal 14
C Relay 3
Terminal 15
N/C Relay 3
Terminal 16
N/O Relay 4
Terminal 17
C Relay 4
Terminal 18
N/C Relay 4
CONTROLS & INDICATORS
POWER/TX
LED1
Dual color LED. Illuminates red while receiver is
booting up; changes to green when boot-up is
successful and unit is ready to operate. If this LED
fails to turn green, power unit off for 15-20
seconds, then reapply power.
LED2
Illuminates green while relay 1 is energized
LED3
Illuminates green while relay 2 is energized
LED4
Illuminates green while relay 3 is energized
LED5
Illuminates green while relay 4 is energized
REL1 –REL4
Four SPDT output control relays
RF1 or 2
RF module that transmits/receives data
SEL1
Dip switches for changing address & frequency

AIR-EAGLE®SR
2.4 GHz RF Receiver
MODEL 38-5000-AC
RELAY OPERATION
Relays energize based on commands received fromthe transmitter. See
table below for relay mode configuration forthis receiver:
TX BUTTON
OR INPUT
ACTIVATED
RELAY OPERATION –MODE
1
Relay #1 Energizes, Maintained Momentary
2
Relay #2 Energizes, Maintained Momentary
3
Relay #3 Energizes, Maintained Momentary
4
Relay #4 Energizes, Maintained Momentary
Maintained Momentary –Relay mimics button or input –when
depressed or closed, relay will be energized; when released, relay
de-energizes
DIGITAL ADDRESS & FREQUENCY SET-UP
The unit is shipped from the factory with SEL1 switches set so that unit is
receiving commands on Digital Address “1” / Frequency “1”. If you wish to
change these default settings, follow the instructions onthe table below.
1) Remove power from unit.
2) Remove top cover.
3) Select desired digital address and/or network frequency using table
below.
4) Reattach cover and apply power.
5) Programming is now complete.
DIGITAL ADDRESS SET-UP
SEL1
(SW1-4)
Digital
Address
SW1
SW2
SW3
SW4
1 (default)
OPEN
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
OPEN
3
OPEN
CLOSED
OPEN
OPEN
4
CLOSED
CLOSED
OPEN
OPEN
5
OPEN
OPEN
CLOSED
OPEN
6
CLOSED
OPEN
CLOSED
OPEN
7
OPEN
CLOSED
CLOSED
OPEN
8
CLOSED
CLOSED
CLOSED
OPEN
9
OPEN
OPEN
OPEN
CLOSED
10
CLOSED
OPEN
OPEN
CLOSED
11
OPEN
CLOSED
OPEN
CLOSED
12
CLOSED
CLOSED
OPEN
CLOSED
13
OPEN
OPEN
CLOSED
CLOSED
14
CLOSED
OPEN
CLOSED
CLOSED
15
OPEN
CLOSED
CLOSED
CLOSED
16
CLOSED
CLOSED
CLOSED
CLOSED
FREQUENCY SET-UP
SEL1
(SW5-7)
Network
Frequency
SW5
SW6
SW7
1 (default)
OPEN
OPEN
OPEN
2
CLOSED
OPEN
OPEN
3
OPEN
CLOSED
OPEN
4
CLOSED
CLOSED
OPEN
5
OPEN
OPEN
CLOSED
6
CLOSED
OPEN
CLOSED
7
OPEN
CLOSED
CLOSED
8
CLOSED
CLOSED
CLOSED
SW8& SW9 Not used on this model
SPECIFICATIONS
Power Supply
100-250 VAC, 5 W, 50/60 Hz
Relay Contacts
SPDT 5 amp @ 120VAC or 30VDC per
channel
Fuse Protected
2 amp
Receiver Frequency
2.4 GHz Spread Spectrum
Receiver Range
Up to 600feet
Note: Range figures are estimates, based on free-air terrain with limited sources of
interference. Actual range will vary based on transmitting power, orientation of transmitter
and receiver, height of transmitting antenna, height of receiving antenna, weather
conditions, interference sources in the area, and terrain between receiver and transmitter,
including, but not limited to, indoor and outdoor structures such as walls, metal objects,
trees, buildings, hills, and mountains.
Digital Addresses
Sixteen independent digital addresses
Network Frequencies
Eight independent network frequencies
Operating Temperature
-40oF to +185oF
Enclosure
Polycarbonate, IP66 (NEMA 4)
Weight
Approx 2.11 lbs.
APPROVALS
United States (FCC)
MCQ-XBEE3
Canada (IC)
1846A-XBEE3
Europe (CE)
ETSI
ACCESSORIES
Standard Antenna (Included):
2.4GHz TNC “Rubber Duck” Antenna
49-1201
Mobile/Base Antennas –
Used to help achieve max range in both nonline of sight andline of
sight applications. - Contact BWI Eagle for recommendations
2.4GHz Thru-Hole Mount Mobile Antenna
49-2201
2.4GHz Magnet Mount Mobile Antenna
49-2202
2.4GHz Omni Directional Base Antenna
49-3201
2.4GHz Yagi Directional Base Antenna
49-3202
High Quality Coax Cables –
Used to connect external high gain antennas to control unit
Flex Coax Cable w/Connectors –Available in
5’,15’,25’,30’,40’,60’,80’,100’ Lengths
49-4000-XX
(XX = # of
Feet)
Bulkhead Extensions –
Used to provide an external antenna connection whenmounting
control unit inside another enclosure
TNC Male to TNCBulkhead Cable Assembly -
Available in 2’, 4’, 7’ Lengths
49-5004-X-ISO
(X = # of Feet)
LIMITED WARRANTY STATEMENT
BWI Eagle Inc. warrants the Air-Eagle Remote Control System, if properly used and
installed, will be free from defects in material and workmanship for a period of 1 year after
date of purchase. Saidwarranty to include the repair or replacement of defective equipment.
This warranty does not cover damage due to external causes, including accident, problems
with electrical power, usage not in accordance with productinstructions, misuse, neglect,
alteration, repair, improper installation, or improper testing. This limited warranty, and any
implied warranties that may exist understate law, apply only to the original purchaser of the
equipment, and last only for as long assuch purchaser continues to own the equipment.
This warranty replaces all other warranties, express or implied including, but not limited to,
the implied warranties or merchantability and fitness for a particular purpose. BWI Eagle
makes no express warranties beyond those stated here. BWI disclaims without limitation,
implied warranties of merchantability and fitness for a particular purpose. Some jurisdictions
do not allow the exclusion of implied warranties so this limitation may not apply to you. To
obtain warranty service, contact BWI Eagle for a return material authorization. When
returning equipment to BWI Eagle, the customer assumes theriskof damage or loss during
shipping and is responsible for the shipping costs incurred.
DOCUMENT DATE: 11/04/2021 / PRODUCT REV. 10