Byron Home Easy HE-440 User manual

RE-INVENTING THE HOME
HOME
easy
HE-440 Outdoor Remote
Control 4Gang Kit
V1.0
OFF: An additional safety feature of the HE440 is the ability to switch off the
power as per a normal socket.
Unused accessory Channels should be set to OFF
INSTALLATION WARNING:
ON INSTALLATION TURN OFF YOUR MAINS ELECTRIC SUPPLY
This product should be fitted by a competent person in accordance with the
instructions listed below and with the relevant clauses of the IEE wiring regulations
BS7671.
For fixed installation only
1. Remove the front cover by
unscrewing the front cover.
Installation Guide:
Wiring Remote Socket:
On the outdoor enclosure you will see that there are a number of rubber entry spaces
(‘Entry blanks’) on each side, depending on location and wiring setup a number of
these can be removed.
If installing the HE440 with conduit from the sides or top attachment,a 5mm hole
must be drilled through the bottom left drainage hole.This will allow for any
condensation forming in the conduit,to drain out.
Caution: opening the drainage hole will affect the IP rating of the product. Ensure that
jetted water is not directly sprayed onto the unit.
Do Not drill out the drainage hole when installing the Outdoor socket into a dusty
environment.Always install the unit via the bottom cable entry,making sure that a 5mm
hole is drilled into the lowest point in the conduit system.
The HE-440 allows you to control up to 4
separate outdoor electrical products
independently using the HomeEasy
remote control timer, with a maximum
combined load of 3000W.
AUTO: Allows the Remote Control to switch on/off
the HE440. See Pairing/Deleting with Remote
ON: Sets the Outdoor socket as a standard outdoor socket.
USE THIS OPTION WHEN USING GARDEN
MACHINERY SUCH AS A LAWNMOWER OR HEDGE CUTTERS.
-Selectable timer setting
-12 Programmable memory Settings
-Security Mode Setting
-Single and Daily Timer Functions
easy
HOME
The HE440 should be used in conjunction with a fused spur connection, all connections
to the socket need to be made as instructed, making sure that the cable used is
appropriate for the installation environment, free from stress & terminals are tightened
fully.
-Single and Daily Timer Functions
-IP56 Weather Proof
-30 Metre Wire Free Range
-CR2032/23A Battery (Included)
Product Specification:
4 Gang Remote Control Receiver: HE-440
Input: 230V - 240V ~50Hz
Range:30 Metres (Open Distance)
Frequency: 433.92MHz
Max Load: 3000W
(Combined Resistive load)
IP56 (Lid Closed)
Warning: Never Exceed the Product Specification
Remote Control PIR: HE-403
Battery: 23A & CR2032 (Included)
Range:30Metres (Open Distance)
Frequency: 433.92MHz
Indoor use only
3. Using the back half of the unit as a template, mark
all four corners onto your chosen surface. Insert
suitable wall plugs and secure to the wall using
number '8' screw (recommended size).
2: In the back half of the unit, in all four corners are
purpose made holes for fixing your HE440 to your
intended surface.The HE440 needs to be mounted
onto a flat, vertical surface, free from grease, loose
material and any corrosive substances.We
recommend a house or sturdy garden wall.
Recommended Setup:
Voltage In:
230-240V ~ 50Hz
Channel 3 Out
Channel 1 Out
Channel 2 Out
Channel 4 Out
Once removed the entry blanks
are removed,appropriate cable
glands need to be installed (not
included).
Input Power: (See Wiring Diagram)
1: Switch off and isolate the mains power before Installing or altering the
electrocal connections and remove the terminal covers.
2: Send the cable through the gland and into the HE440.
3: Cut back the cable to reveal the 3 separate wires
  L= Live  Brown
  E= Earth  Green & Yellow
  N= Neutral  Blue
4: Now strip each wire, exposing 10mm of its core
5: Insert the exposed core wires into their related terminals
and clamp down by tightening the respective screw. replace
the terminal covers and tighten the cabel glands,making
sure wall wires are secure.
Wiring Diagram:
Accessory Output 1 Accessory Output 2 Accessory Output 3
Accessory Output 4
Input Power
230 - 240V ~50HZ
 
= Live   Brown
= Earth   Green & Yellow
= Neutral   Blue
The HE-200 Remote Control Timer can be paired with 16 separate
receiver units,to select the required unit code, press the unit
button unitl the required number is displayed.
Each unit code will indavidually can indavidually operate single
channel or all 4 channesl.
The HE-200 comes with a preset to Group code A.When
using additional remote control timers you will need to
select a new group code.
To select a new group code, remove the battery cover and
using a small screw driver, rotate the group dial to a new
setting e.g.Group B
HE440
HE200
WARNING:
You MUST install an earth cable between the origin of the installation and the earth
terminal of the outdoor socket.This must be insulated inside a sleeve protector within
the conduit.
If using metal conduit, earth continuity must be maintained between conduits. Seal
Conduit and conduit entry with a non setting conduit sealant. Purchasable form you
local electrical retailer.
Operating Mode:
Output:
230-240V ~ 50Hz
3000W Combined
6. Reconnect the mains power,the HE440 is now ready programming
(See Pairing/Deleting with Remote).
Replace the front cover and tighten the screws.
Each Acessory Output Channel can operate in 3 seperate modes,use the slide
switch on each channel to select the mode setting.

C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Contact Details:
433MHz
R&TTE
APPROVED
CH Byron Electrical United Kingdom.www.chbyron.com
A
B
DK
FIN
F
D
GR
LT
IRL
I
L
NL
P
E
S
UK
BG
CZ
EST
H
IS
LV
M
N
SK
SLO
CH
PL
RO
0560
Tel: [phone]
Fax: [phone]
Web: www.chbyron.com
E-mail:
[email protected]
Contact:   Helpline: 0845 2301 231
HE200 Programable Remote Control:
Display Functions:
Functions:
1: 12 Programmable Memory Spaces
2: 24Hr Time
3: Timer Setting "On"
4: Timer Setting "Off"
5: Security Mode
6: Timer Mode - Single Timer Setting
7: Timer Mode - Daily Timer Setting
8: Low Battery Warning
9: Unit Code Display
10:Transmission Indicator Signal
Receiver Select
Switch "On" Selected Receiver
Switch "Off" Selected Receiver
Clock Setting
Program Timer/View
Enter
Delete/Pause
Select Up/Down
The HE-200 Remote Control Timer can be paired to 16 separate
receiver units,select the unit code by pressing the unit button.

Unit Setting:
The HE-200 comes with a preset to Group code A.When
using additional remote control timers you will need to
select a new group code.
To select a new group code, remove the battery cover and
using a small screw driver, rotate the group dial to a new
setting e.g.Group B
G
I
K
+_
Remove the battery cover form the back of the remote control.
The HE-200 includes 2 batteries:
 LCD Display: 1 x CR2032 -Byron SX100 (Included)
 RF Transmission: 1 x 23A - Byron SD100 (Included)
Remove the required battery and replace
with new,making sure the polarity matches
the internal markings.
Changing Batteries:
Switching On/Off :
1. Select the unit by
pressing the "unit"
button until the
correct number is
displayed on the
screen.
2. Press the "On"
button, the receiver
socket will switch on.
Never exceed
3000W Combined
maximum load.
3. Press the "Off" button to switch the receiver unit off.
Setting Clock
The remote control displays the time in a 24hr format, to set the time.
1. Press and hold the
clock button for +3sec.
The hrs will now start
to flash
2. Use the
buttons to select
the hours and
press Enter.
3. The minutes will now start to flash, set using the up and down arrows to
select the minutes and then press enter.
Up to Six remote control units can be paired with each HE440 Accessory
Output Channel.To program a channel press the "Learn" button e.g.
accessory output channel 1.
Deleting Remote Control:
To delete a remote control that has been paired with a Accessory Output
Channel, simply press the "Learn" button . The LED will start to blink; press the
"Off" button on the remote control, the LED will blink twice to confirm that the
remote control has been removed from the receiver sockets memory.
Channel reset:
To delete all the remote control units from the memory of the Accessory
Output Channel, hold the "Learn" button for more than 6 seconds, the LED will
start to blink continuously.Press the learn button again, the LED will blink
twice to confirm the deletion of all remote controls form the receiver memory.
Pairing/Deleting with Remote Control:
Accessory Ouput
Channel 1
Learn
Button
LED
The LED will start to flash,
now press the "ON" button
on the remote control,the
LED will stop flashing and the
acessory output will switch
"ON/OFF".
The units are now paired
together, you can test this by
pressing the selected
"ON/OFF" button
Setting Timer :
The HE-200 remote control timer can store up to 12 different timer
programs,ideal for switching on lights throughout the home for added
security.
To program the remote control:
1. Press and hold the "Timer" button for 3 seconds, the
display will show the 12 available memory spaces.Use
the arrows keys to select a memory space, the display
will also show any programmed times already saved.
Press "Enter" to select the program space.
2. Press and hold the "Timer" button for 3 seconds, the
display will show the 12 available memory spaces.Use
the arrow keys to select a memory space, the display will
also show any programmed times already saved.
Press "Enter" to select the program space.
3. The start or On time will start to flash, use the arrow keys to select the hours
and press enter to select the min.
Now select the finish or off time.
4. Finally select the program mode using the arrows keys and press enter to
confirm.
Daily Timer Setting: Activates the program daily
Security Setting: Selecting the security mode will switch the
receiver units "On/Off" randomly through out the set time.
 On = between 40Min - 2Hrs
 Off = between 40Min - 3Hrs
Single Timer: Activates the program for a single time only.
Always refer to the original instruction when using with additional
products
5. Press Timer to exit the setting mode