C Prox Ltd FP1 User manual
1
C Prox Ltd (inc Quantek)
59 Sheffield Road, Dronfield, S18 2GF
Standalone Fingerprint Access Control
FP1
User Manual
Please read the manual carefully before installing this unit
2
1. Packing list
Name
uantity
Remarks
Fingerprint reader
FP1
1
Infrared remote control
1
User manual
1
Screw driver
1
Special screw tool
Diode
1
IN4004
Ru er
wall
plug
4
Φ6mm
×25 mm, used for fixing
Self
-
tapping
screws
4
Φ4mm
×25 mm, used for fixing
Please ensure that all the a ove contents are correct. If any are missing please notify us immediately.
2. Description
The FP1 is a metal zinc alloy shell standalone fingerprint reader for access control. It uses the American
Atmel’s MCU, with precise electron circuit and good productive technology. This unit applies world
advanced fingerprint identification technology, making it safe and relia le, which means it is an ideal
choice for situations demanding high security. Its programming is done y infrared remote control or
master fingerprint. It can store up to 1,000 fingerprints, including two master fingerprints and 998 user
fingerprints. Each fingerprint has one ID code.
3. Functions
Sleeping function
High environmental awareness energy-saving control system, with auto sleep and wake up function. The
sleeping power consumption is less than 0.20W.
Master fingerprints operation function
This device can add/delete users fingerprints y master fingerprints quickly and easily. (One add master
fingerprint, one delete master fingerprint.
Infrared programmer
Supplied with an infrared programmer to allow easy add/delete of fingerprint. Useful if a user fingerprint
needs to e deleted without them eing present.
Lock driving function
With NC, NO and COM, the control time is 0 – 99 seconds. (0s is 50ms). Wires are isolated from the inner
circuit, the contactors current is 2A.
Anti-tamper alarm function
When the unit is disassem led, the internal uzzer will sound a consecutive alarm for one minute.
3
4. Specification
Input voltage
12V dc ± 10%
Sleeping current consumption
≤20mA
Idle current consumption
≤80mA
Door relay contact load
2A
Operating
temperature
-
20 to 5
0
⁰C
Operating humidity
20% to 95% RH
Fingerprint capacity
1000
Resolution
450 DPI
Fingerprint input time
<1s
Identification time
<1s
FAR
<0.0000256%
FRR
<
0.0198%
Structure
Zinc alloy
Dimensions
115 x 70 x 35 mm
Weight
500g
5. Installation
•Remove the ack cover using the supplied security driver
•Use the ack cover to mark the four fixing holes and one ca le hole, drill holes.
•Fit ack cover firmly to the wall using the wall plugs and self-tapping screws.
•Thread the wires through the hole.
•Attach the front to the ack cover.
4
6. Wiring
Colour Function Description
Yellow OPEN Exit utton
Red 12V + 12V + DC regulated power input
Black GND 12V – DC regulated power input
Blue NO Relay output NO
Purple COM Relay output COM
Orange NC Relay output NC
7. To reset to factory default
a. Disconnect power from the unit.
. Press and hold the ‘Reset’ utton on the PCB whilst powering the unit ack up.
c. On hearing three short eeps, release the ‘Reset’ utton, system is now ack to factory default.
Please note only installer data is restored, user data will not e affected.
8. Sound and light indication
Operation Status Indicator Light Colour Finger Sensor Light Buzzer Description Buzzer
Power On Slow flash in red Bright Long ring
Di
-
Sleeping Slow flash in red Goes out
Voided Key Short ring Di
Enter Programming Red Goes out Long ring Di -
Programming Orange
Input Fingerprint
successful Green Long ring Di ---
Input Fingerprint
Failed
3 short rings Di Di Di
Unlock the Door Green Goes out Long ring Di -
Alarm Quick flash in red Bright Continuous long ring Di
－
……
5
9. Programming guide
10. Anti-tamper alarm
When the unit is removed illegally the anti-tamper switch will e activated and the internal alarm will
sound for one minute. Or it can e turned off in the following ways: Input .Master fingerprint. or .User
fingerprint. or .Master code.
To enter programming mode
.*. Master code .#.
9999 is the default master code
To exit programming mode
.*.
Note that to undertake the following programming the master user must be logged in
To change the master code
.0. .New code. .#. .New code. .#.
The master code is any 4 digits
To add a fingerprint
.1. ID code .#. .Input fingerprint. .Input fingerprint. .#.
ID code range is 1 to 1000. ID code 1 is master add fingerprint, ID code 2 is master delete fingerprint, ID code 3 to
1000 are users’ fingerprints. Each ID code e assigned one fingerprint, master fingerprints must e added y ID code.
Advice for adding fingerprints: when the LED lights up, input fingerprint. It gives a short eep when the fingerprint is
inputted for the first time. Release fingerprint, then input the same fingerprint again. The unit will emit a longer eep
and the LED will turn green, this means the fingerprint has een successfully added. If the operation has failed, three
short eeps will e emitted, attempt the process again. In order to improve the success rate, please put middle of the
fingerprint on the middle of the induction area.
To add users continuously
ID code will e auto generated, from 3
to 1000
.7. .1
st
user fingerprint twice. … .Nth user fingerprint
twice. .#.
To delete a fingerprint
.2. .ID code. .#.
Users can e deleted continuously without exiting programming mode
To delete users continuously
Each fingerprint only needs to e
inputted once
.8. .1
st
user fingerprint. … .Nth user fingerprint. .#.
To delete all fingerprints
This process deletes all users, so use
with care
.2. 0000 .#.
Add/delete users by master fingerprints
To add fingerprint users
Input .Master add fingerprint. .1
st
user fingerprint twice. …
.Nth user fingerprint twice. .Master add fingerprint.
To delete fingerprint users
Input .Master delete fingerprint. .1
st
user fingerprint. …
.Nth user fingerprint. .Master delete fingerprint.
To set door open time
.4. 0 – 99 .#.
0 – 99 is to set the door relay time to 0 – 99 seconds
To unlock the door
In stand y state, input valid user fingerprint, door will open
Table of contents
Other C Prox Ltd IP Access Controllers manuals
