Ca Go Ortho-Safety-Collar User manual

EN
Ortho-Safety-Collar
Assembly instructions

2
Safety notices ................................................................................................................ 
General information ..................................................................................................... 
Intended use ................................................................................................................... 
Scope of delivery ........................................................................................................... 
Installation ...................................................................................................................... 
General notes on care ................................................................................................ 
Statutory warranty / guarantee ............................................................................. 
The present assembly instructions is the translation of the original assembly
instructions.
Contents

3
Notice
Provides information about how
to handle the product or refers to
a passage in the user manual that
deserves special attention.
Safety notices
This user manual contains various types of notice.
The notices are designed as follows:
Separate instructions
Refers you to other assembly
instructions for your FS200 Life
which describe the respective
assembly step in more detail if
needed.
Caution
Warns you about incorrect
behaviour that can result in
material and environmental
damage.
Danger
Potential hazards for your health
and the health of your co-riders and
other road users if you fail to observe
the respective instructions or do not
take corresponding precautions.

4
The Ortho-Safety-Collar is an attachment for the transport box of the
FS200 Life. It increases the child’s safety during transport and also serves
as a convenient headrest, should your child fall asleep during the ride with
your Ca Go.
Fig.1
Fig.2
The Ortho-Safety-Collar is the
required basis for our All-Weather-
Top (Fig.2).
General information

5
Even when the Ortho-Safety-Collar
is used, all children must be seated in
appropriate seats (suitable for their
height and weight) and strapped in
safely. We strongly recommend using
bicycle helmets.
Intended use
The Ortho-Safety-Collar is not
compatible with the Life Soft Top,
nor with the transport box lid.
The screw connections should be
checked for tight seat at regular in-
tervals and retightened as required.
If the Ortho-Safety-Collar shows
cracks or signs of deformation after
a crash or collision, it must be re-
placed (safety-relevant component).

6
Scope of delivery
Fig.3
The Ortho-Safety-Collar consists
of several individual parts, EPP,
moulded sheet metal components
and screw connections. It is delivered
pre-assembled (Fig.3). Assembly requires the following
additional tools:
Allen key, 5mm, and Torx® T30

7
Installation
Fig.4
If Ca Go Ergonomic-Child-Seats
are already installed in the box, they
have to be removed before installing
the Ortho-Safety-Collar. To do this,
remove the two M6 screws (5mm
Allen key) and lift out the Ergonomic-
Child-Seats (Fig.4).
You can ind more information in
the assembly instructions for the
Ergonomic-Child-Seat by Ca Go.

8
The Ortho-Safety-Collar can now be placed on the edge of the transport box.
The holes of the connection plates must be positioned above the threads in
the transport box (Fig.7).
Fig.5 Fig.6
Fig.7
Remove the M6 screws at the transport box frame/steerer tube
(5mm Allen key) (Fig.5) and the M6 countersunk head screws of the
side plastic cover (Torx® T30) (Fig.6).

9
Finally, the Ergonomic-Child-Seats can now be reinstalled (Fig.10).
Fig.8 Fig.9
Screw the side plates of the Ortho-Safety-Collar, including the plastic covers,
back on using the M6 countersunk head screws, but do not fully tighten the
connections yet (Fig.8).
As the next step, the M6 screws can be screwed in. To do this, press down at
the centre of the Ortho-Safety-Collar so that it sits lush on the edge of the
transport box, then tighten the M6 screws to 5–8Nm (Fig.9). Now also tighten
the side plates of the Ortho-Safety-Collar to 5–8Nm.
Fig.10
You can ind more information in
the assembly instructions for the
Ergonomic-Child-Seat by Ca Go.

10
The cleaning and care requirements for the Ortho-Safety-Collar are the same
as for the transport box. In many cases, water is all that is needed to do the
job. If needed, you can use a mild detergent, such as dishwashing liquid or
hand soap.
General notes on care
Never use aggressive cleaning agents,
acids or solvents to clean the set.
Such substances can corrode or
damage surfaces. This may affect
the stability of the components.

11
Statutory warranty / guarantee
Service
The legal statutory warranty applies. You can ind more details on the warranty
on our website: www.cagobike.com/en/warranty
Export to the USA and Canada is not permitted (product liability)!
If you have questions concerning this user manual, please contact your
Ca Go dealer or your Ca Go service team.

Item no. 930 005 48
Managing directors: Franc Arnold
Company register
Court of record: District Court Koblenz / register no.: HRB 26998 / VAT Id no. DE326206636
Responsible for distribution and marketing of the user manual: Ingo Kahnt
Ca Go Bike GmbH reserves the right to change product speciications without prior notice.
Typographical errors, mistakes and modiications reserved. Version of 03/2023
©Reproduction, reprint and translation, as well as any use for economic purposes (including as extracts, in print or electronic form)
without prior written approval is forbidden.
Published by:
Ca Go Bike GmbH
Am Autobahnkreuz 7
56072 Koblenz
Germany
[phone]
inf[email protected]om
www.cagobike.com