Cadet SoftHEAT User manual

EBKN BUILT-IN THERMOSTAT KIT
http://cadetheat.com/install/softheat
For how-to videos or more information, please visit:
ESPAÑOL ver la guía del propietario en cadetheat.com/espanol/ebkn
cadetheat.com
855.CADET.US
Vancouver, Washington tested to UL standards
OWNER’S GUIDE

SAVE THESE INSTRUCTIONS
IMPORTANT INSTRUCTIONS
2
1. Read all instructions before in-
stalling or using this thermostat.
2. Use this thermostat only as
described in this manual. Any
other use not recommended by
the manufacturer may cause
re, electric shock, or injury to
persons.
3. Do not insert or allow foreign
objects to enter any ventilation
or exhaust opening as this may
cause an electric shock or re, or
damage the heater or thermostat.
4. To disconnect thermostat turn o󰀨
power to heater circuit at main
disconnect panel.
5. Do not operate any thermostat
after it malfunctions. Disconnect
power at main disconnect panel
and have thermostat inspected
by a qualied electrician before
reusing.
6. A thermostat has arcing or spark-
ing parts inside. Do not use in
areas where gasoline, paint, or
ammable liquids are stored.
When using electrical appliances, basic precautions should always be
followed to reduce the risk of re, electric shock, and injury to persons,
including the following:
WORKING WITH ELECTRICITY
TOOLS REQUIRED
Phillips Screwdriver
Wire Strippers Wire
Connectors
Volt Meter
®
®
®
If you are uncomfortable working with electricity, running electrical supply
wire or installing a circuit breaker, please consult a licensed electrician.
Unanswered questions? Call our technical support team in Vancouver,
Washington toll free 855.223.3887 or outside the USA 360.693.2505.
®
• Verify power has been turned o󰀨 before starting any work!
• Follow the instructions in your SoftHEAT Baseboard Owner’s Guide (included with your
heater) until prompted to make thermostat connections.
TIPS BEFORE YOU BEGIN
PARTS OF YOUR THERMOSTAT
C
O
M
F
O
R
T
Lorem ipsum
Z
O
N
E
control knob
wired on right
wired on left
C
O
M
F
O
R
T
Lorem ipsum
Z
O
N
E
rounded corners to
front of heater
®

240/208 or 208 volt LEFT SIDE
120 volt LEFT SIDE
INSTALLATION INSTRUCTIONS
1. Remove the SoftHEAT baseboard end cap by removing the screw and clip located on
the back of the heater and sliding the end cap o󰀨. Keep the screw and clip to use with
the thermostat.
2. Slide the thermostat end cap onto the heater. Make sure no wires are caught be-
tween the thermostat and heater. Fasten to the baseboard using the screw and clip
set aside.
3. Make wire connections below, depending on your heater model, and whether you
have a right end or left end wiring compartment. For 240 or 208 volt, both supply
wires (black and white) are hot.
3
1. All electrical work and materials
must comply with the National
Electric Code (NEC), the Occu-
pational Safety and Health Act
(OSHA), and all state and local
codes.
2. Use copper conductors only.
3. Use only on SoftHEAT baseboard
heaters.
4. Turn o󰀨 power to heater at main
disconnect panel.
5. Connect grounding lead to
grounding screw provided on the
heater.
6. Use wire connectors (not included)
for all connections.
DOUBLE POLE (4-WIRE) - 240/208 or 208 VOLT
DOUBLE POLE (4-WIRE) - 120 VOLT
A. Connect the two black
thermostat wires to the two loose
heater wires.
B. Connect the two hot supply
wires to the two red thermostat
wires.
Wrap supply (white) wire with
black tape to identify it as hot.
240/208 or 208 volt RIGHT SIDE
4. Tuck all the wires back into the wiring compartment, and make sure the connections
are tight.
5. Screw the wiring compartment cover back on.
6. Return to your SoftHEAT baseboard Owner’s Guide and go to Mount heater to wall
to complete installation.
120 volt RIGHT SIDE
A. Connect the two black wires
from the thermostat together.
B. Connect the neutral (white)
supply wire to the white heater wire.
C. Connect the black wire from
the baseboard to one of the red
thermostat wires.
D. Connect the remaining red
thermostat wire to the remaining
supply wire.
A
B
C
D
A
B
C
D
A
B
B
A
A
B
B
A

4
Make sure all wires are properly connected and installation is complete
before you turn on the heater.
OPERATING INSTRUCTIONS
Rev 03/02/17 #706982
Reduce-Reuse-Recycle
This product is made primarily of recyclable materials. You can reduce your carbon footprint
by recycling this product at the end of its useful life. Contact your local recycling support
center for further recycling instructions.
WARRANTY
For more e󰀨ective and safer operation and to
prolong the life of the heater, read the Owner’s
Guide and follow the instructions. Failure to
properly maintain the heater will void any warranty
and may cause the heater to function improperly.
LIMITED ONE YEAR WARRANTY: Cadet will
repair or replace any Cadet EBKN thermostat
found to be defective within one year after the
date of purchase.
These warranties do not apply:
1. Damage occurs to the product through improper
installation or incorrect supply voltage;
2. Damage occurs to the product through
improper maintenance, misuse, abuse, accident,
or alteration;
3. The use of unauthorized accessories or
unauthorized components constitutes an
alteration and voids all warranties. Refer to Cadet
website or call customer service at 855.223.3887
or 360.693.2505 for list of authorized accessories
and components.
4. CADET’S WARRANTY IS LIMITED TO
REPAIR OR REPLACEMENT.
5. IN THE EVENT CADET ELECTS TO REPLACE
ANY PART OF YOUR CADET PRODUCT, THE
REPLACEMENT PARTS ARE SUBJECT TO
THE SAME WARRANTIES AS THE PRODUCT.
THE INSTALLATION OF REPLACEMENT PARTS
DOES NOT MODIFY OR EXTEND THE UNDER-
LYING WARRANTIES. REPLACEMENT OR
REPAIR OF ANY CADET PRODUCT OR PART
DOES NOT CREATE ANY NEW WARRANTIES.
If you believe your Cadet product is defective,
please contact Cadet during the warranty period,
for instructions on how to have the repair or
replacement processed.
Parts and Service
Visit cadetheat.com/parts-service for information
on where to obtain parts and service.
More frequently asked questions on our website here: cadetheat.com/support/FAQ
©2017 Cadet Printed in USA
To register your product, visit cadetheat.com/product-registration
How to operate your heater
The room temperature is controlled by the thermostat on the heater. Once installation is
complete and power has been restored, follow the steps below for your thermostat:
1. Turn the thermostat knob all the way to the right.
2. When the room reaches your comfort level, turn the knob to the left, just until it clicks
and the heater turns o󰀨. The heater will automatically keep the room temperature
around this setting.
3. To reduce the room temperature, turn the knob to the left. To increase the room
temperature, turn the knob to the right.
Black
Black
Ground
L1
L2
All wiring connections inside wiring compartment
Black
Black
Red
Red
All wiring connections inside wiring compartment
Ground
L1
Neutral
Black
Black
Red
White
Black
Red
Figure 3
Wiring Diagram for use with
240 and 208 volt heater
Figure 2
Wiring Diagram for use
with 120 volt heater
INTERNAL HEATER WIRING DIAGRAMS