CAMBRIONIX MultiCharger14-2.4A User manual

MultiCharger14-2.4A
User Manual
© 2023-02 Cambrionix Ltd. All rights reserved. EN

MultiCharger14-2.4A Page 1 of 23
1. Table of Contents
1. Table of Contents 1
2. Your MultiCharger14-2.4A at a glance 3
3. Safety 4
3.1. Signal word panel 4
3.2. Safety alert symbol 5
3.3. Pictograms 5
3.4. Product modification 5
3.5. Power supply 6
3.6. Storage and Installation 6
4. Getting Started 8
4.1. Unpacking your product 8
4.2. What's Included 8
4.3. Connecting to the mains 9
4.4. Charging 9
4.5. Cables 9
4.5.1 Fan Behaviour 9
4.6. Registration 9
4.7. Help and Support 9
4.8. Cleaning your MultiCharger14-2.4A 11
5. Product Specifications 12
5.1. Input Power Requirements 12
5.2. Output Power 12
5.3. Physical specifications 12
5.4. Packaged information 13
5.5. Consumables and Placing Orders 13
5.6. Power Supply 14
6. Troubleshooting 16
6.1. Common troubleshooting tips 16
6.2. Logging through LiveViewer 16
6.3. Hardware Failure 16
6.4. Device connection 17
6.5. Hub connection issues 18
6.6. Using with a headless system 19
6.7. Software troubleshooting 19
7. Disposal 20
8. Returns and Damaged Products 21
8.1. What if my order arrives with an issue? 21

MultiCharger14-2.4A Page 2 of 23
8.2. What happens after I have requested a Return? 21
9. Compliance and Standards 22
10. Terms and Conditions 23

MultiCharger14-2.4A Page 3 of 23
2. Your MultiCharger14-2.4A at a glance
The MultiCharger14-2.4A has been designed primarily for desktop use, being highly compact and
quiet. It provides 12W of charging power to each of its USB 2.0 Type-A ports, allowing mobile devices
to be charged quickly, safely and reliably. All ports can be controlled using Cambrionix software to
enable charging whilst monitoring important port and device information.
The MultiCharger14-2.4A can charge attached USB devices without using a local computer, and our
intelligent charging algorithm allows almost any device to be charged at its optimum rate (up to 2.4A).
The firmware can be updated to enable new charging profiles to be added, ensuring the
MultiCharger14-2.4A can charge the latest devices. It is ready to charge out-of-the-box.
You can download the latest version of this manual and all product user manuals from our website at
the following link. www.cambrionix.com/product-user-manuals

MultiCharger14-2.4A Page 4 of 23
3. Safety
This user manual is for informational purposes only, it contains information for the start-up and
operation of this product. Note: the contents and the product described are subject to change
without notice. To avoid injuries and damage, observe the safety instructions in the user manual.
This manual has been arranged to follow the IEC/ICEE 82079-1 standard. This is to facilitate the easier
understanding and location of information relating to the MultiCharger14-2.4A. Any errors or
omissions can be reported using our support ticket system (seeHelp and Support). This way, any
issues that are discovered can be acted on quickly and we can update the documentation to reflect
this.
Understanding and observing the instructions in this user manual are prerequisites for hazard-free
use and safety during operation. This user manual cannot cover all possible applications. If you would
like additional information or if problems arise that are not sufficiently addressed in this manual,
please ask your distributor or contact us directly using the means preferred, which are located on the
back cover of this manual.
CAUTION
Personal Injury and Damage to the product
Always observe the safety instructions in this user manual
3.1. Signal word panel
Depending on the probability of serious consequences, potential dangers are identified with a signal
word, the corresponding safety colour, and if appropriate, the safety alert symbol.
CAUTION
Indicates a potentially hazardous situation that, if not avoided, may result in moderate or
minor (reversible) injury.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in damage to the
product and its functions, or to property in its proximity.

MultiCharger14-2.4A Page 5 of 23
3.2. Safety alert symbol
Use of the safety alert symbol indicates a risk of injury.
Observe all measures that are marked with the safety alert symbol in order to avoid injury
3.3. Pictograms
These symbols will be used throughout this documentation to alert to any potential dangers or any
actions that must be taken.
Warning Signs
Electrical hazard Fire Hazard
Mandatory action signs
Read operating instructions Mandatory regulation
3.4. Product modification
Cambrionix products are designed and manufactured to meet the requirements of UK and
international safety regulations. Modifications to the product could affect safety and render the
product non-compliant with relevant safety standards, resulting in injury or damage to the product.
CAUTION
An electric shock or personal injury may occur
Do not modify the product in any way.
Do not dismantle the product.

MultiCharger14-2.4A Page 6 of 23
CAUTION
Fire, or personal injury may occur
Do not obstruct air vents on the product.
Do not cover the product in or place near combustible material.
CAUTION
Damage to your product may occur
Do not bend or compress any part of the product.
3.5. Power supply
This section describes the safety precautions you must follow when using the external power supply.
CAUTION
An electric shock or personal injury may occur
Do not use a damaged power cord or plug, or a loose power socket.
Do not touch the power plug with wet hands.
Do not allow liquids to come into contact with the unit or power supply.
CAUTION
Damage to your product may occur
Do not short circuit the Power Supply Unit (PSU) supplied with your product.
Do not disconnect the power cord while the product is being used.
Do not bend or pull the power cord with excessive force.
Do not use a power supply that exceeds the power supply specifications
within this manual
3.6. Storage and Installation
This section describes safety precautions you must follow when installing and storing your
MultiCharger14-2.4A.

MultiCharger14-2.4A Page 7 of 23
CAUTION
An electric shock or personal injury may occur
Do not place the power cord near heat sources.
Connect the plug only to an earthed socket.
CAUTION
Damage to your Cambrionix product may occur
Operate the product only in an environment where the ambient
temperature is inside the operating temperature range.
Operate the product only in an environment where the relative humidity is
inside the operating range.
Be careful not to leave the power cord underneath a heavy object.
CAUTION
Overheated power sockets may cause a fire
Do not overload the power socket that your hub is connected to.
Insert the power plug all the way into the socket so that it is not loose.
CAUTION
Overloading the brackets may cause failure
The rack brackets for all our products are not designed to be used in a mobile
application, bracket failure could occur if the units are not supported fully e.g
Shock during road transport.

MultiCharger14-2.4A Page 8 of 23
4. Getting Started
This manual provides a reference for end-users installing for the first time and using their hub
afterwards. As well as a guide for product safety-related information.
The MultiCharger14-2.4A is intended to be used in an indoor static environment in which the
environment falls within the tested specifications to provide charge, sync and management
functionality. Please see the physical specifications section of this manual for information on the
environment specifications.
4.1. Unpacking your product
When you have received your product, please check the packing slip inside the box to ensure all
contents and quantities are correct before opening. This is to avoid retesting and repackaging any
items that are not required.
When opening the packaging, use a suitable method to open the box i.e, do not use a knife. This is to
ensure the product is not damaged.
CAUTION
Personal Injury and Damage to the product
There will be a label on the hub advising you to read the User manual before
use. This will need to be removed before use as it may be covering host ports,
vents etc.
4.2. What's Included
lMultiCharger14-2.4A Hub
l2m Mains power cable (Country specified on order including fuse for the UKplugs)
lPower Supply Unit
Part description Part number
Power Supply Unit 200421
UK Power cable 200144
US Power cable 200327
EU Power cable 200329
AUSPower cable 200337
IND Power cable 200341

MultiCharger14-2.4A Page 9 of 23
4.3. Connecting to the mains
Connect the Power Supply Unit (PSU) to the hub using the 4-Pin Mini DIN plug. Connect the power
cable to the PSU. Making sure you adhere to local safety regulations, connect the power cable to the
100 – 250 VAC mains power outlet and switch the hub on using the small power switch located
adjacent to the power input connector on the hub. When the device is switched on, a LED next to the
power input will be illuminated. The hub is now ready to charge attached devices.
Periodic inspections should be made to power supply cables and any USB cables for any signs of
damage. If any damage is found, replace the damaged cord before further use.
Please note that USB specifications require a minimum 100 mA charge current to be available during
data transfer. As indicated in above, if the attached device has a BC1.2 compliant CDP port, the
device can draw up to 2.4A whilst transferring data.
4.4. Charging
Your MultiCharger14-2.4A will allow your device to charge at the maximum rate possible up to 2.4A.
The way that charging takes place is the MultiCharger14-2.4A will provide the device with a capability
to charge and the devices USB charging controller will determine the maximum amount of charge it
wants to draw down.
Although a maximum charge rate of 2.4A is possible, the device itself determines the exact rate and
as such you may not see the maximum amount of charging on every device type that is connected.
4.5. Cables
Some USB cables are data transfer only, and some are power delivery only. There are also options
that can handle both tasks. Be sure to verify a cable’s abilities before purchasing it and select a cable
which can handle the speeds and power transfer that you require. We would advise using the cable
that was provided with the device to connect to our hubs.
4.5.1 Fan Behaviour
Your MultiCharger14-2.4A has an inbuilt fan used to cool the product when internal temperatures rise
above a set threshold. On power up the fan will spin for approximately a second before turning off.
The temperature at which the fan should begin to cool the device is 26 °C, the fan will be at max
speed when the internal temperature reaches 60. Once the MultiCharger14-2.4A is below internal
temperature of 26 the fan will switch off.
4.6. Registration
You may register your product at www.cambrionix.com/product-registration
4.7. Help and Support
FAQs and help can be found on the Help page here
lwww.cambrionix.com/help_pages/help.

MultiCharger14-2.4A Page 10 of 23
You can raise a support ticket for more in depth support here
lhttps://cambrionix.atlassian.net/servicedesk/customer/portals
You can also download any of our manuals and keep up to date at the link here
lwww.cambrionix.com/product-user-manuals
When contacting support, please supply the product information for the hub in question. This can be
found on the Device Information Plate which is either on the underside or back of the unit.
Providing serial and Purchaseorder numbers, can help identify your specific product and speed up
the process.

MultiCharger14-2.4A Page 11 of 23
4.8. Cleaning your MultiCharger14-2.4A
Cleaning the product is generally not required, although in some instances it may be necessary if
excess dirt/ dust/ hair has accumulated, or if minor liquid spillages have occurred on the module
during operation or storage.
CAUTION
Electric shock or personal injury may occur
If there is a dirt/ spillage over a ventilation slot, external data/ power
connector or product aperture, please remove power from the unit without
touching the liquid and seek advise before reapplying power
lEnsure that the product is switched off and the power cord is removed from the product. Hold
the power cable by the plug and do not touch either the plug or the power cord with wet or
damp hands as an electrical shock may result
lWipe the product with a clean, dry and soft cloth. Do not use detergents which contain alcohol,
solvent or surface-active agents. Do not spray water or detergent directly onto the product
lMildly dampen a soft and dry cloth in water and wring thoroughly to clean the product as
required
lDry the product thoroughly once the cleaning has finished
lReconnect the power cord and use your product as advised once cleaning is complete

MultiCharger14-2.4A Page 12 of 23
5. Product Specifications
The MultiCharger14-2.4A is manufactured in the UK
5.1. Input Power Requirements
Input Voltage (V) 12
Input Current (A) 15
Input Connector 4-Pin Mini DIN
5.2. Output Power
Output Voltage (V) 5
Output Voltage Tolerance (%) +/-5
Output Current, Max per Port (A) 2.4
Output Power, Max per Port (W) 12
Output Power, Total (W) 174.72
5.3. Physical specifications
Upstream connector type
Downstream connector type USB 2.0 Type-A
Maximum Downstream Data Speed per Port (Gbps)
Ambient Operating Temperature range °C 0-35
Relative, non-condensing, humidity operating range (%) 5 - 95
Dimensions WxDxH (mm) 198.3 x 73 x 40
Weight (kg) 1.6
Number of Downstream ports 14
Ports Lifetime
Standard USB connections have a minimum rated lifetime of 1,500 cycles of insertion and removal.
USB-C receptacles have a minimum rated lifetime of 10,000 cycles of insertion and removal. This is
an industry-standard.

MultiCharger14-2.4A Page 13 of 23
One thing you can do to prolong the lifetime of the ports on your MultiCharger14-2.4A is to use
"sacrificial cables" in between the hub and your charging cables so when you repeatedly connect/
disconnect you are only going to wear the cables rather than the hub.
5.4. Packaged information
Boxed Dimensions WxDxH (m) 0.47 x 0.12 x 0.31
5.5. Consumables and Placing Orders
Below is a list of any Consumable products you may require for your MultiCharger14-2.4A including
the cables you will require to connect devices to the hub.
Cables USB 2.0 Type-A
If you require any spare parts, such as the power cable or cable, these can be ordered by quoting the
product part number and the spare part number (available from the Getting Started section).
These can be ordered from the reseller or solution partner you purchased your MultiCharger14-2.4A
from, or from Cambrionix directly.
To find one of our partners local to you please visit www.cambrionix.com/partners where you can
learn about the local vendors and distributors that can assist you and find their contact information.

MultiCharger14-2.4A Page 14 of 23
5.6. Power Supply
Input Voltage (V) 100-240
Input Current @ 115VAC (A) 4
Input Current @ 230VAC (A) 2
Input Frequency (Hz) 50-60
Input Connector C14
Output Voltage, Max (V) 12
Output Current, Max (A) 15
Output Power, Max (W) 180
Output Connector 4-Pin Mini DIN
Dimensions WxDxH (mm) 210 x 85 x 46

MultiCharger14-2.4A Page 15 of 23
Pin Function
1 +Vo
2 +Vo
3 -Vo
4 -Vo
*-V is connected to AC input ground.

MultiCharger14-2.4A Page 16 of 23
6. Troubleshooting
If you experience any issues with your MultiCharger14-2.4A; please try the following troubleshooting
steps, if the issue is not addressed in this section, please get in touch with your local vendor or
Cambrionix. To contact Cambrionix Support please see Help and Support.
6.1. Common troubleshooting tips
Some tips and information to check first.
lIf you plug a device (phone, USB stick) into the hub, does it appear to the OS (device manager/
system info etc.).
lIf you directly connect the same device to the port the hub is in, does it appear to the OS.
lTry switching the cables with ones that are working/ use cable from a hub that is working.
6.2. Logging through LiveViewer
If you are experiencing a bug or an issue, we may ask you to obtain some logs of the behaviour, to see
in more detail what is happening. To get logs of the behaviour use the following steps to get a zip file
of the logs.
1. Open LiveViewer (if this is not already downloaded, then go onto our website and download
both the API and LiveViewer) www.cambrionix.com/software
2. Once in LiveViewer, on the left-hand side of the screen, select the settings section.
3. Once in the settings section, select the API tab.
4. In the API section click the "cog" button on the right hand side of the local API
5. Click the “select all” tick box and then the save button.
6. After this is enabled, use the hub in a way that causes the issue you are seeing.
7. Wait for the issue to occur, i.e. device disconnects.
8. Make a note of the time and date that the issue occurs then go back to the API page in
LiveViewer, and press the zip logs.
9. Once you have the logs un-tick the “select all” box and save your settings.
10. Send the logs to us for us to take a look at.
The API keeps a maximum of 20 logs at 256Mb each, so the latest one is usually smaller. If a crash
occurs, you would see a smaller log file and the next instance of API shuffles the existing ones
6.3. Hardware Failure
If the Hardware fails the LEDs can flash in a pattern to determine the type of failure. The power
LEDwill flash the pattern if no LEDs are present on the downstream ports.
The unit will blink four times, followed by eight long or short flashes, which then repeat. The flashes
are a number in binary which match a number in our error code list.
i.e if the LED flashes the following - BBBB SLSSSLSS, the binary number is 01000100.

MultiCharger14-2.4A Page 17 of 23
6.4. Device connection
If you are seeing any device connection issues please read through the following trouble shooting
steps to see if this resolves the observed behaviour.
Device issues when updating
We have found that during updates on some devices the connection can be dropped or lost on the
device, this is due to devices going in and out of the bootloader and requiring different power levels.
In most instances disabling CDP has resolved this issue for our customers.
You can disable CDP through NVRAM settings either by going through the advanced settings and
turning "Sync charge" off or through the API and disabling it via code. For example, the instructions
would be below using the command line.
settings_unlock
settings_set sync_chrg 0000000000000000
Unstable device connection
Some devices can have unstable connections with your host system through the MultiCharger14-
2.4A. We have only observed this behaviour in a very few amount of devices, disabling CDP this has
resolved all issues and the connections are stable.
You can disable CDPthrough NVRAMsettings either by going through the advanced settings and
turning "Sync charge" off or through the APIand disabling it via code. For example, using the
command line, the instructions would be as below.
settings_unlock
settings_set sync_chrg 0000000000000000
Battery information for Android
If you are observing an issue displaying battery information on Android devices ensure firstly you
have ADBtool installed and open then try these things in order.
1. Check that developer options are enabled on the android device, and then that USB debugging
is also enabled.
2. If you have done this step and it still does not work, go to Developer Options and click ‘Revoke
USB debugging authorisations’. Unplug the cable and reconnect.
3. If this still doesn’t work, turn off the developer options at the top, re-enable it, and re-enable
‘USB Debugging’.
4. You can get detailed info directly from ADB at each step to diagnose things:

MultiCharger14-2.4A Page 18 of 23
adb.exe shell dumpsys battery # use -s serial_number as first options
if you have more than 1 android attached
Unknown devices
Sometimes, within Liveviewer and device manager, the connected device may show up as an
unknown device.
This can be due to the host system needing to be trusted on the device. This can be done on the
device itself on the initial connection.
This could also be due to an insufficient number of endpoints available on the USB controller in the
host system. This limitation within the USBcontroller can only be resolved if you connect fewer
USBdevices to the controller in question.
For Apple devices there is a setting called "USB accessories" which can be activated, Once activated it
will reduce the amount of times a device will need to be unlocked/ trusted. More information can be
found at the link https://support.apple.com/en-gb/HT208857.
Cannot connect any more devices
Sometimes, you may reach the endpoint limit of your USB controller and this may stop you from
being able to attach any more devices to your host system.
You can create more space is to change connections from USB3 to USB2. You can change the
connection by disabling USB3 in the BIOSon startup.
A much simpler way is to use USB2 cables instead of USB3 cables, limiting the connection to USB2.
6.5. Hub connection issues
If you there are issues with the hub and connecting to your host system, please see below
troubleshooting solutions.
Hub not connecting to host
If you see that the MultiCharger14-2.4A is not connecting to the host system, one of the issues may
be caused by the USBdrivers on your host system not being up to date. It is good practice to ensure
you have the latest drivers and updates installed on your host system, which is usually handled by the
OS, but sometimes may require an update directly from the USB host controllers manufacturer,
which will be found on their website.
USBdrivers required are FTDIdrivers, which can be found on the site https://ftdichip.com/drivers/.

MultiCharger14-2.4A Page 19 of 23
Cannot access the COMport
You may get an error message stating "COM (and then a number) could not be opened (Access is
denied)".
This is because an application has control over the COMport that the hub is connected to, and no
subsequent application can access the hub. To resolve this, you will need to close any other
applications that are using the COMport before trying to use the COMport.
6.6. Using with a headless system
If you are using a headless system with no GUI,then and you require to enable logging for support
issues, you can use the following command to create the logging cfg file manually:
echo
*=debug>/etc/opt/cambrionix/cambrionix.log.cfg
Then after re-producing the problem, you can zip the logs from the folder
/var/log/cambrionix
You may delete the file below when you are finished with it.
/etc/opt/cambrionix/cambrionix.log.cfg
6.7. Software troubleshooting
Some users have noted that the APIcan cause a high level of CPUusage. This can sometimes be
linked to the APIrecorder service. If you are finding this and you are not using it then we would
recommend to uninstall it from your system entirely. Information on how to uninstall programs can
be found in the Removing Software section.