CAMDEN CM-300 User manual

Page 1 of 2
CM-310EE
Exit Switch & Integrated Timer (Ver. 2)
INSTALLATION INSTRUCTIONS
Door Activation Devices
Camden model CM-310EE is an illuminated
Exit switch incorporating a 30 second timer.
The stainless steel faceplate is designed to ush
mount on to a 1 ¾” wide doorjamb.
The ½” x ¾” rectangular translucent button is easy
to push. CM-310EE model is supplied with a LED
light bulb, which is accessed through the front
of the switch. If the unit is powered 24VDC, the
supplied in-line resistors must not be removed.
This switch has been designed specically to
release a magnetic lock from the inside, as per
the BOCA code. When the button is pushed and
released, the lock will release for 30 seconds.
Re-trigger is possible at any time.
The “double break” circuitry has been designed so
that even if the timer fails, depressing the switch
will interrupt power to the magnetic lock.
1. GENERAL DESCRIPTION
2. SPECIFICATIONS
Models CM-300
Operating Voltage 12 or 24 V DC
Time Delay 30 seconds
Contact Rating 4 amps @ 30 VDC
Incandescent
Bulb Life
15,000hrs.@ rated capacity
Mounting 2 x #6-32 machine screws
Lens Colour Green
Legend 'PUSH TO EXIT'
Dimension 2.75” W x 4.5” H x 1 5/16”
(70mm x 114mm x 33mm)
3. INSTALLATION
Mounting
The unit is completely pre-wired for easy installation. Connect
the appropriate wires to your devices as per the enclosed wiring
diagram. Tuck wiring into box (retrot box included), and fasten
switch plate using screws provided.
Wiring
Six color coded leads are provided. This unit will operate on 12 or
24 VDC, with no jumper change required. For convenience it may
be powered by the same power that supplies the magnetic lock.
The two pairs of Red & Black wires connect to 12 or 24 VDC.
One pair supplies power to the timer, and the other pair powers
the light. The internal timer and the push button are connected
in series with the Green & White wires. This is how the “double
break” feature works. Therefore, the unit must be wired as
shown.
The Green wire goes to the positive input wire of the magnetic
lock, and the White wire goes to a source of + Voltage. Please
refer to the enclosed wiring diagram for typical hook-up.
Important:
CM-310EE models have connected lead wires with
black-colored heat shrink (over an in-line resistors).
If powered 24V; Do not remove in-line resistors.
If powered 12V; Cut (remove) in-line resistor on the
black lead.
4. LIMITED WARRANTY
Camden Door Controls Inc. warrants this product to be free
from defects for 3 years from date of manufacturing. Visit our
web site at www.camdencontrols.com to see our complete
warranty policy, including limitations and the procedures for
product returns.
CM-310EE

Call: 1.877.226.3369 / 905.366.3377
Visit: www.camdencontrols.com
Opening New Doors to
Innovation, Quality and Support!
Page 2 of 2
File: CM-310EE Series
Installation Instructions.indd R2
Revision: 30/10/2018
Part No.: 40-82B040
CM-310EE SERIES
INSTALLATION INSTRUCTIONS
CM-310EE Egress Switch Wiring Diagram (Ver 2.0)
SCALE: NONE DRAWING No: DRG-CM310EE-031703 FILE NAME: CM-310EE Diagram.vsd
DRAWN BY: DGW DATE: 03/18/03 REVISED: 03/20/12
5502 Timberlea Blvd. Mississauga, Ontario L4W 2T7
Camden Door Controls
White
Green
Red (Light)
Red
Black
+
-
Magnetic
Lock
12/24
VDC
POWER
Note: CM-310EE models have a connected lead wire with black-colored heat shrink (over the in-line resistors)
Note: If powered 24V; Do not remove
in-line resistors.
If powered 12V; Cut (remove) in-line resistor on the black lead.
Note: 1.For 12V operation, cut off inline-resistor (on Black wire only). For 24V operation, leave inline resistor in place. 2.Bulb Replacement. Access to light bulb is obtained by first removing front rectangular lens with a thin blade screwdriver. Then, using a pair of needle-nose pliers, carefully pull light bulb straight out. Re-installation is reverse of above sequence. Be sure to line up both pins before pushing bulb in.
Optional Motion Detector shown. If not used, wire White to Positive Terminal of power supply. Power In Relay Out
Wire White to “+” 12/24 VDC,
or,
through Relay of Motion Detector (optional)
Inline
Resistor
Inline Resistor
Motion Detector
Black (Light)
Rear View of CM-310EE switch and Faceplate
“+”
“-”