CAME AGT V User manual

AGT V - AGT V BF
En
g
l
i
s
h
USER MANUAL
FA0 1 37 7 - EN

Page 2- Manual FA01377-EN - 02/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Functions of the keys
Activation and selection of entry panel.
The function is available only when the line is free.
Enable/Disable the automatic door opener function if pressed for more
than 3 seconds. The status of this function is indicated by the led near
the key
Repeatedly pressing it adjusts the volume of the ringtone: low, medium,
high, o (red LED on).
In conversation activating the key excludes the microphone until it is
activated again or the communication ends.
Auxiliary 2 / Porter call
AUX2 LED: signals a request to be called back by the porter
Door release/open-gate command if pressed for > 3 seconds (if the
function is enabled).
Door release LED: flashes when calling/ fixed when the open-gate
function is active.
Use soft, dry or slightly damp cloths to clean the terminal; do not use any chemical
products.

Page 3- Manual FA01377-EN - 02/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Basic functions
Call in progress.
Answering a call.
Active communication.
Open the door for the calling entry
panel.
End the call.

MASTER
MASTER
SLAVE
SLAVE
Page 4- Manual FA01377-EN - 02/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Self-connection
Press the key to activate video
communication with the entry panel.
With multiple video entry panels, pressing
the button all the video entry panels
will be displayed in succession.
Video bouncing
In the event of a simultane-
ous call on several exten-
sions all will ring, but the
video will be activated only
in the receivers configured
as "MASTER".
It is however possible to
transfer the display to a
"SLAVE" receiver by press-
ing the key .
Lift the handset to start au-
dio communication with the
entry panel.

CONTACT ME
ALARM!
C
ONTACT ME
Contact me
Page 5- Manual FA01377-EN - 02/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Porter functions
The functions described in this chapter are only available in systems with a porter
switchboard/porter desk.
Notification of call by the porter
When the LED turns on, it indicates
that the porter wishes to be called back.
The LED turns o when communicating
with the porter.
Alarm signalling The activation of an alarm contact
connected to the dedicated input of the
receiver, activates the sending of a signal
to the porter and this is notified on the
receiver through an intermittent acoustic
signal for about 10 seconds.
Request to be called back by the porter
If properly configured, press the button
to send a message to the porter that
you wish to be called back.
Open-gate function/status
Where allowed by the system and correctly
configured, you can send an operator
opening/closing command by pressing and
holding the key. The LED next to it
indicates the operator status.
☞The function must be activated on the
receiver when the call is being associated
during system programming

> 3s
Page 6- Manual FA01377-EN - 02/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Door status function
Where the system is enabled accordingly, the LED next to the button indicates the current
status of the door.
The function is active during the steps that involve communicating with the entry panel and
the signal refers to the entrance associated with the entry panel.
Automatic door-release function
This function is especially useful for
businesses as it allows you to open the
entrance automatically once the call button
has been pressed on the entry panel.
Press and hold the button for more
than 3 seconds to enable/disable the
function.
The LED next to the button switches on
to indicate that the function has been
enabled.
☞No communication is activated and the
call ends automatically.

Page 7- Manual FA01377-EN - 02/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions
Decommissioning and disposal. Dispose of the packaging and the device at the end of its life
cycle responsibly, in compliance with the laws in force in the country where the product is used.
The recyclable components are marked with a symbol and the material's ID marker.
THESE INSTRUCTIONS MUST BE ATTACHED TO THE APPLIANCE, THE DATA AND INFORMATION SHOWN HEREIN ARE TO BE
CONSIDERED AS SUBJECT TO CHANGE AT ANY TIME AND WITHOUT THE NEED FOR ANY ADVANCE WARNING.
These keys are used to adjust the brightness, contrast and colour of
the display when the video is active.
Touch any key to access the menu.
Press briefly to adjust the parameter, pressing
continuously allows a quick adjustment.
Press to scroll through the parameters.
Wait for a few seconds to exit the menu.
Adjustment of brightness, contrast and colour

CAME S.p.A.
Via Martiri Della Libertà, 15
31030 Dosson di Casier - Treviso - Italy
tel. [phone] - fax. [phone]
Page 8- Manual FA01377-EN - 02/2020 - © CAME S.p.A. - The contents of this manual may be changed, at any time, and without notice. - Translation of the original instructions