Campania International FT-285 User manual

FT
-
285TriadFountain
Two people are recommended for the installation ofthisfountain!
R
evised
December 4, 2017
PumpKitParts List
PK300 pump (1)
#10 stopper(1)
12”length of1/2”BlackNon-kinktubing (1)**
2”length of5/8”cleartubing (1)**
CopperSpiller(1)
2.8 oztubeofSilicone (1)
Wedges(3)
Hose clamps(2)*
*Hoseclamps maybe used asflow restrictors
** Tubing has been preassembled
-WINTERCARE-
Fountainbowls/topsandotherfountaincomponents,whichcollect water, shouldnotbeleftoutsideinthewinter since anycomponent,
whichfillswithwater andfreezesmaycrack.Likewise, componentssuchaspedestals,whichremaininabasin,filledwithwater,
whichthenfreezes,mayalsocrackor crumble. Ideally, therefore, afountainshouldalwaysbestoredindoorsor inadryprotected
place suchasacoveredporchawayfromtheelements. However, ifafountainmustbeleftoutside:
(1) Removepump, rubber stoppers, drainpipes, finials,andother smallcomponentsfor storageindoors. Note that stoppersor
drainpipesareremovedtoallowdrainageintheeventwater accumulatesinanybasin.
(2) Raisefountainbasefromgroundwithwood stripssothat basewill notfreeze tothegroundsurface.
(3) Cover or wrapthefountainwithburlapor other absorbentmaterial (oldblanket or towel) andthencover securelywith
plastic,making surethat water will notaccumulate inthebasinor other fountaincomponentandfreeze;
(4) Checkfountainperiodicallytoinsurethat plastic issecureandwater isnotaccumulating inanyfountaincomponent.
-GENERALFOUNTAINTIPS-
Install fountainsonalevel surface. Youwill needaproperlygrounded110-volt (AConly) GFCI protectedreceptaclenear the
fountainfor your pump. All pumpsaresubmersible andmustbecompletelyunderwater tofunctionproperly. Testall pumpsand
adjusttofull outputprior toassembly. Itisnotrecommendedthat fountainsbeplaceddirectlyongrass or dirt. Positionthechannel
opening at thebaseofeachfountaintoward theelectrical outlet tobeusedsince thepump
cord willbethreadedthroughthisopening.
CheckoutYouTubefor a“Howto”video.
For moreCampania product informationvisit www.campaniainternational.com
All of ourcaststone is proudly
FOUNTAININFORMATION:
Thisfountain holdsapproximately5gallonsof water.
Thisfountain usesalargefountain cover.
(FTNCOV-LG)
Compatible with#10 Refill Device and LEDkits
(Aspecialstopper isrequiredtousethe refill kit for
thisfountain.)
TOOLSREQUIRED:
Bubble Level
PUMPINFORMATION:
PF320 - 320GPH Pump
16 FTcord length

FT
-
285TriadFountain
Two people are recommended for the installation ofthisfountain!
R
evised
December 4, 2017
Assemble your fountainonalevel surface capable ofholdingaminimumof464 poundswithanapproximate 1.5squarefoot
footprint.
FT-285E (107lbs)
16”Lx13.5”Wx15”H
FT-285C(162lbs)
30”Lx20.25”Wx9”H
FT-285A(148 lbs)
29.75”Lx9”Wx9.25”H
FT-285B(5lbs)
4”Lx4”Wx1”H
FT-285D(2lb)
1.25”Lx5.25”Wx3.75”H
1. Place thebase(FT-285E)into position where thefountain will beinstalled,
ensuringthatit is level.
2. Center thebasin (FT-285C)on thebase(FT-285E)
3. Assemblethepump kit
a. NOTE:All pumps come with1 adapter already insertedinto the
pumpand 2 adapters securedto thepower cord.
i. Thisfountainuses themediumadapter provided.
b. Usingahoseclamp, attach the12”piece of1/2”non-kink tubingto
thepump outlet.
c. Place thestopper around thepump cord approximately8”fromthe
pump.
4. Feed thepump cord through theholein thebasin (FT-285C)and through the
channelin thebottomofthebase(FT-285E).
5. FIRMLY press thestopper into theholeevenly.
a. Note:Usingthehandleofascrewdriverorhammer works bestto
press thestopper in place.
6. Center thewater feature (FT-285A)over thepumpkit and stopper hole.
7. Fit the5/8”clear end ofthetubingovertheCPVCpipeprotrudingfromthe
bottomofthewater feature (FT-285A).
a. Note: Youcando this stepwithoutholding thewater feature over
thebasinand after youlevelit
8. Spread athin bead ofsiliconewhere thespiller will beplaced in thewater
feature(FT-285A) bycreatingarectangular shapethatboarders justthe
narrowchannel.
9. Press thespiller into place ensuringthatthebentpartoverhangs thewater
feature.
a. Note: Cleanaway any excess silicone.
10. Place thewater controlplate(FT-285B)overthepipein thetop ofthewater
feature(FT-285A).
11. Fit thepump cover door(FT-285D) into thepump cover (FT-285C).
12. Letthefountain sit 24 hours beforefillingwith water.