Campbell SDM-CD16D User manual

SDM-CD16D 16 Channel Digital
Control Port Expansion Module
Revision: 8/07
Copyright © 2000-2007
Campbell Scientific, Inc.

Warranty and Assistance
The SDM-CD16D 16 CHANNEL DIGITAL CONTROL PORT
EXPANSION MODULE is warranted by CAMPBELL SCIENTIFIC, INC. to
be free from defects in materials and workmanship under normal use and
service for twelve (12) months from date of shipment unless specified
otherwise. Batteries have no warranty. CAMPBELL SCIENTIFIC, INC.'s
obligation under this warranty is limited to repairing or replacing (at
CAMPBELL SCIENTIFIC, INC.'s option) defective products. The customer
shall assume all costs of removing, reinstalling, and shipping defective
products to CAMPBELL SCIENTIFIC, INC. CAMPBELL SCIENTIFIC,
INC. will return such products by surface carrier prepaid. This warranty shall
not apply to any CAMPBELL SCIENTIFIC, INC. products which have been
subjected to modification, misuse, neglect, accidents of nature, or shipping
damage. This warranty is in lieu of all other warranties, expressed or implied,
including warranties of merchantability or fitness for a particular purpose.
CAMPBELL SCIENTIFIC, INC. is not liable for special, indirect, incidental,
or consequential damages.
Products may not be returned without prior authorization. The following
contact information is for US and International customers residing in countries
served by Campbell Scientific, Inc. directly. Affiliate companies handle
repairs for customers within their territories. Please visit
www.campbellsci.com to determine which Campbell Scientific company
serves your country. To obtain a Returned Materials Authorization (RMA),
contact CAMPBELL SCIENTIFIC, INC., phone [phone]. After an
applications engineer determines the nature of the problem, an RMA number
will be issued. Please write this number clearly on the outside of the shipping
container. CAMPBELL SCIENTIFIC's shipping address is:
CAMPBELL SCIENTIFIC, INC.
RMA#_____
815 West 1800 North
Logan, Utah 84321-1784
CAMPBELL SCIENTIFIC, INC. does not accept collect calls.

SDM-CD16D Table of Contents
PDF viewers note: These page numbers refer to the printed version of this document. Use
the Adobe Acrobat® bookmarks tab for links to specific sections.
1. Introduction..................................................................1
2. Control Specifications.................................................2
2.1 General......................................................................................................2
2.2 Output Specifications................................................................................2
3. Power Considerations.................................................3
4. Installation....................................................................4
4.1 Controlled Device Connections................................................................4
5. Address Selection Switches.......................................5
6. Datalogger Instructions ..............................................7
6.1 CRBasic....................................................................................................7
6.2 Edlog.........................................................................................................7
7. Theory of Operation ....................................................8
8. Program Examples......................................................8
8.1 CRBasic Example.....................................................................................9
8.2 Edlog Example .........................................................................................9
Figures
1. SDM-CD16D..............................................................................................1
2. Equivalent Output Driver Circuit ...............................................................2
3. Connection Block Diagrams.......................................................................3
4. Use of Terminal Blocks..............................................................................5
5. Address Selection Switch...........................................................................6
Tables
1. Datalogger to SDM-CD16D Connections..................................................4
2. Switch Position and Addresses...................................................................6
i

This is a blank page.

SDM-CD16D 16 Channel Digital Control
Port Expansion Module
The SDM-CD16D (see Figure 1) is a synchronously addressed peripheral. It has 16
control ports.
FIGURE 1. SDM-CD16D
1. Introduction
The SDM-CD16D expands the digital output capability of Campbell Scientific
dataloggers. The outputs can be set to 0 or 5 V by the datalogger. In addition to
being able to drive normal logic level inputs, when an output is set HI a ‘boost’
circuit allows it to source a current of up to 100 mA, allowing direct control of
low voltage valves, relays etc.
The SDM-CD16D is a synchronously addressed datalogger peripheral. Three
ports on the datalogger are used to address the SDM-CD16D then clock out the
desired state of each of the 16 control ports. Up to sixteen SDM-CD16Ds may
be addressed, making it possible to control a maximum of 256 ports from three
datalogger SDM ports.
In CRBasic, instruction SDMCD16AC is used to control the SDM-CD16D. In
Edlog, Instruction 104 is typically used; older CR7 dataloggers use Instruction
29.
Older CR7 dataloggers with pre-OS7.1 software may not have
the necessary instruction. Ensure that your datalogger contains
the appropriate instruction before using.
NOTE
1

SDM-CD16D 16 Channel Digital Control Port Expansion Module
2. Control Specifications
2.1 General
Compatible dataloggers: CR800, CR850, CR1000, CR3000, CR5000,
CR10(X), CR23X, CR7 and 21X
Operating voltage: 12 VDC nominal (9 to 18 V)
Current drain at 12V DC: 100 µA typical (All ports HI, no load)
Total cable length: 6 m (CR10/10X, CR23X, 21X), 180 m (CR7)
2.2 Output Specifications
Output Voltage (no load): Output ON/HI, Nominal 5 V (Minimum 4.5 V)
Output OFF/LO, Nominal 0 V (Maximum 0.1 V)
Output Sink Current: Output will sink 8.6 mA from a 5 V source*
Output Source Current: Output will source 36 mA @ 3 V,
115 mA short-circuited to ground*
Max. Output Current: 400 mA at 50°C and 12 V supply (see NOTE below)
(total all outputs)
The maximum current should be derated under the following
conditions: 50 mA for every 10°C above 50°C and/or 50 mA for
every volt above 12 V.
NOTE
Operating temp.: -25°C to +70°C standard
Size: 230 mm wide x 100 mm high x 24 mm deep
Weight: 350 g
EMC Status: Complies with EN55022-1:1998 and
EN50082-1:1998
* If more detailed output characteristics are required, experienced users should
consult the equivalent circuit diagrams shown in Figure 2, below.
0.6V Drop
Output
Output
580R
Output set ON/HI Output set OFF/LO
5
1
0
R
39
R
V
5V, 0Ω
FIGURE 2. Equivalent Output Driver Circuit
2

SDM-CD16D 16 Channel Digital Control Port Expansion Module
3. Power Considerations
The SDM-CD16D power requirements are large compared to most Campbell
Scientific products when driving significant loads. For many applications an
external power supply, as shown in Figure 3, is recommended to power the
SDM-CD16D.
For some applications it may be convenient to use the datalogger supply to
power the SDM-CD16D, as shown in Figure 3. For long-term applications, the
lead-acid power supply available with Campbell Scientific dataloggers should
be used, allowing the batteries to be float charged. Alkaline batteries are not
recommended for long term applications.
Connection with External Supply
Connection with Datalogger Supply
GND
EXTERNAL
9 TO 18V DC
+ –
SDM-CD16D DATALOGGER
12V C1
C2
C3
SDM-C1 or C1
SDM-C2 or C2
SDM-C3 or C3
12V
SDM-CD16D DATALOGGER
GND
12V
C1
C2
C3
SDM-C1 or C1
SDM-C2 or C2
SDM-C3 or C3
FIGURE 3. Connection Block Diagrams
If the 21X power supply is used to power the SDM-CD16D, all
low level analog measurements (thermocouples, pyranometers,
thermopiles, etc.) must be made differentially. This is a result of
slight ground potentials created along the 21X analog terminal
strip when the 12 V supply is used to power peripherals. This
limitation reduces the number of available analog input channels
and may make an external supply for the SDM-CD16D essential.
NOTE
3

SDM-CD16D 16 Channel Digital Control Port Expansion Module
4. Installation
For correct operation the SDM-CD16D must be installed where there is no risk
of water ingress or condensation.
The order in which connections are made is critical.
Always connect 12 V first, followed by ground, then the
control ports.
CAUTION
For datalogger connections, see Table 1, below. Please refer to Figure 4 for
details of how to use the spring-loaded terminals.
TABLE 1. Datalogger to SDM-CD16D Connections
Connection Order
SDM-CD16D
CR800, CR850,
CR1000, CR7,
CR10(X), CR23X, 21X
CR3000,
CR5000
Function
First 12 V 12 V on datalogger or
external supply 12 V on datalogger or external supply Power
Second
C1
C2
C3
or G
C1
C2
C3
G
SDM-C1
SDM-C2
SDM-C3
Common Ground
Data
Clock
Enable
On a CR7, SDMs connect to the ports at the upper right corner
of the 700X control module.
NOTE
Multiple SDM-CD16Ds may be wired in parallel by connecting the datalogger
side of one SDM-CD16D to the next.
The transient protection of the SDM-CD16D relies on a low resistance path to
earth. Ensure that the ground return wire has as low a resistance as possible.
Where long cable runs are likely, or where lightning damage is a possibility,
the SDM-CD16D can be fitted with gas discharge tubes. Please contact
Campbell Scientific for details.
For CR7 dataloggers, the total cable length can be up to 180 m.
For our other dataloggers, the total cable length connecting
SDM-CD16Ds to SDM-CD16Ds and the datalogger should not
exceed 6 m. Total cable lengths in excess of 6m will adversely
affect communication performance.
NOTE
4.1 Controlled Device Connections
The SDM-CD16D uses spring-loaded terminal blocks, which provide quick,
vibration resistant, connections. The output terminals are labeled 1 to 16. A
common ground connector is provided between each pair of terminals.
4

SDM-CD16D 16 Channel Digital Control Port Expansion Module
Use a screwdriver in either the top or front slot, as appropriate, to open the
terminal spring. Strip any insulation from the wire to give 7 to 9 mm bare wire.
Push the wire into the opening, and, while holding it in position, withdraw the
screwdriver to release the spring. The wire will now be firmly held in place.
See Figure 4, below.
You cannot reliably insert more than one solid-core wire into
one terminal connector unless the wires are soldered or clamped
together. When inserting more than one stranded wire, twist the
bare ends together before insertion.
NOTE
Use a screwdriver in appropriate slot
to release spring tension
Strip insulation
and insert wire
FIGURE 4. Use of Terminal Blocks
5. Address Selection Switches
Each SDM-CD16D can have 1 of 16 addresses. The factory-set address is 00.
Table 2 shows switch position and the corresponding address. Figures 1 and 5
show the position of the switch. Note that you will have to remove the
mounting bracket to gain access to this switch.
5

SDM-CD16D 16 Channel Digital Control Port Expansion Module
TABLE 2. Switch Position and
Addresses
Switch Setting Base 4 Address
0 00
1 01
2 02
3 03
4 10
5 11
6 12
7 13
8 20
9 21
A 22
B 23
C 30
D 31
E 32
F 33
Use a screwdriver to select address
FIGURE 5. Address Selection Switch
6

SDM-CD16D 16 Channel Digital Control Port Expansion Module
6. Datalogger Instructions
6.1 CRBasic
The SDMCD16AC instruction in CRBasic is used by our CR800, CR850,
CR1000, CR3000, and CR5000 dataloggers. With this instruction, a port on
an SDM-CD16D is enabled/disabled (turned on or off) by sending a value to it.
A non-zero value will enable the port; a zero value disables it. The values to
be sent to the SDM-CD16D are held in the Source array.
Syntax
SDMCD16AC ( , , )Source Reps SDMAddress
Remarks
The SDMCD16AC instruction has the following parameters:
Source The Source parameter is an array which holds the values that
will be sent to the SDM-CD16D to enable/disable its ports. An
SDM-CD16D has 16 ports; therefore, the source array must be
dimensioned to 16 times the number of Repetitions (the
number of SDM-CD16D devices to be controlled). As an
example, with the array CDCtrl(32), the value held in
CDCtrl(1) will be sent to port 1, the value held in CDCtrl(2)
will be sent to port 2, etc. The value held in CDCtrl(32) would
be sent to port 16 on the second SDM-CD16D.
Reps The Reps parameter is the number of SDM-CD16D devices
that will be controlled with this instruction.
SDMAddress The SDMAddress parameter is used to define the address of
the SDM-CD16D that will be controlled with this instruction.
Valid SDM addresses are 0 through 14. Address 15 is reserved
for the SDMTrigger instruction. If the Reps parameter is
greater than 1, the datalogger will increment the SDM address
for each subsequent device that it communicates with.
6.2 Edlog
Instruction 104 is used by the CR10/10X, CR23X, CR7 and 21X to control the
SDM-CD16D, and Instruction 29 is used by older CR7s. The Instruction
descriptions are shown below.
7

SDM-CD16D 16 Channel Digital Control Port Expansion Module
Instruction 104 – SDM-CD16D used with CR10/10X, CR23X,
CR7and 21X dataloggers
Parameter Type Description
1 2 Reps (No. of modules sequentially addressed)
2 2 Starting Address (base 4: 00..33)
3 4 Starting Input Location
Execution Time = 2 ms per Rep for the CR10/10X and CR23X
3.5 ms per Rep for the 21X and CR7
Instruction 29 – SDM-CD16D used with older CR7s
Parameter Type Description
1 2 Reps (No. of modules sequentially addressed)
2 2 Device (2 = SDM-CD16D)
3 2 Starting Address (base 4: 00..33)
4 2 Card (Excitation card No.)
5 4 Starting Input Location
Execution Time = 150 ms to 190 ms per Rep
The number of SDM-CD16Ds to be addressed is defined by the Reps
(repetitions) parameter. Each Rep sequentially addresses (00, 01, 02,...32, 33)
SDM-CD16Ds, starting with the address specified in parameter 2 (parameter 3
for Instruction 29).
For each repetition, the 16 ports of the addressed SDM-CD16D are set
according to 16 sequential input locations starting at the input location
specified in parameter 3 (parameter 5 for Instruction 29). Any non-zero value
stored in an input location activates (sets HI 5 V) the associated SDM-CD16D
port. A value of zero (0) de-activates the port (sets LO 0 V). For example,
assuming two repetitions and a starting input location of 33, outputs 1 to 16 of
the first SDM-CD16D are set according to input locations 33 to 48, and
outputs 1 to 16 of the second SDM-CD16D are set according to input locations
49 to 64.
For older CR7s with Instruction 29, the Device (parameter 2) specifies what
type of synchronously addressed peripheral is to be addressed. The Device
code for an SDM-CD16D is 2.
For Instruction 29 only (older CR7s), the Card parameter (parameter 4)
specifies which 725 Excitation Card is being used for the control port signals.
The Reps parameter does not advance beyond the specified Card, requiring
another Instruction 29 for each 725 Excitation Card used.
7. Theory of Operation
On power-up, all SDM-CD16D outputs are off /LO.
The SDM-CD16D is a synchronously addressed peripheral. C2 and C3, driven
high by the datalogger, initiate a cycle. While holding C3 high, the datalogger
drives C2 as a clock line and C1 as a serial data line. The datalogger shifts out
8

SDM-CD16D 16 Channel Digital Control Port Expansion Module
a data bit on C1 (LSB first) on the falling edge of the C2 clock. The SDM-
CD16D shifts in the C1 data bit on the rising edge of the C2 clock.
The first eight bits clocked out represent the SDM-CD16D address. If the
address matches the SDM-CD16D’s address, the SDM-CD16D is enabled. If
enabled, the next 16 bits are shifted into the SDM-CD16D, each bit controlling
one port, the first of which controls output 1.
When the 16 control bits are clocked in, C2 is held high while C3 is pulsed low
then high to latch the control bits. The datalogger then lowers both C3 and C2
to complete the cycle.
8. Program Examples
8.1 CRBasic Example
In the following CR1000 program example, a counter is used to fill an array
called Src( ) that will control two SDM-CD16Ds.
'Dimension Variables
Public src(32)
Dim i, count, mask(16)
'Program
BeginProg
for i=1 to 16
mask(i) = 2^(i-1)
next i
Scan(20,msec,2,0)
count = count + 1
for i=1 to 32
src(i) = count AND mask(((i-1) MOD 16) +1)
next i
SDMCD16AC(src(),2,1)
NextScan
EndProg
8.2 Edlog Example
The example is written for the CR10(X) Measurement and Control Module.
The program concepts presented are the same for the CR23X, 21X and CR7
dataloggers with minor changes in the program code.
In this example, the SDM-CD16D is used to control the temperature between
23°C and 28°C in each of five greenhouses. In each greenhouse the SDM-
CD16D controls a heating unit, a refrigerating unit and an air mixing fan
according to the following conditions:
Heating unit:
Activate when temperature <23.5°C.
Deactivate when temperature >25.5°C.
9

SDM-CD16D 16 Channel Digital Control Port Expansion Module
Cooling unit:
Activate when temperature >27.5°C.
Deactivate when temperature <24.5°C.
Mixing fan:
Activate whenever the heating or cooling units are activated.
Activate for 5 minutes out of every 15 minutes.
The program assumes that the temperature measurements have been made, and
that the average temperature for each greenhouse is computed and stored in
input locations 1 to 5. For further information on loops and input location
indexing, please refer to your datalogger manual.
Input location assignments are as follows:
Input Input
Location Location Label Description
1..5 Temp #1..#5 Avg. temp. greenhouse 1..5
10..14 Heat #1..#5 Heater control, greenhouse 1..5
SDM-CD16D Port 1..5
15..19 Cool #1..#5 Cooler control, greenhouse 1..5
SDM-CD16D Port 6..10
20..24 Fan #1..#5 Fan control, greenhouse 1..5
SDM-CD16D Port 11..15
;{CR10X}
;
*Table 1 Program
01: 5 Execution Interval (seconds)
1: Beginning of Loop (P87) Master loop: end
1: 0 Delay loop at step 30
2: 5 Loop Count
Start heater control logic
2: If (X<=>F) (P89) if temperature is below
1: 1 -- X Loc [ Temp_1 ] heater threshold
2: 4 <
3: 23.5 F
4: 30 Then Do then
3: Z=F (P30) put a ‘1’ into heater control
1: 1 F location
2: 0 Exponent of 10
3: 10 -- Z Loc [ Heat_1 ]
4: End (P95) end ‘then do’
10

SDM-CD16D 16 Channel Digital Control Port Expansion Module
5: If (X<=>F) (P89) if the heater is on (heater
1: 10 -- X Loc [ Heat_1 ] control location <>0)
2: 2 <>
3: 0 F
4: 30 Then Do then
6: If (X<=>F) (P89) check upper threshold
1: 1 -- X Loc [ Temp_1 ] to see if heater should
2: 3 >= be turned off
3: 25.5 F
4: 30 Then Do
7: Z=F (P30) if heater should be turned
1: 0 F off, enter a ‘0’ into
2: 0 Exponent of 10 heater control location
3: 10 -- Z Loc [ Heat_1 ]
8: End (P95) end ‘then do’
9: Else (P94) else, if the heater is off
10: Z=F (P30) enter a ‘0’ into heater
1: 0 F control location
2: 0 Exponent of 10
3: 10 -- Z Loc [ Heat_1 ]
11: End (P95) end ‘then do/else’
End heater control logic
Start cooler control logic
12: If (X<=>F) (P89) if ‘cooler on’ threshold
1: 1 -- X Loc [ Temp_1 ] is exceeded
2: 3 >=
3: 27.5 F
4: 30 Then Do then
13: Z=F (P30) put a ‘1’ into cooler
1: 1 F control location
2: 0 Exponent of 10
3: 15 -- Z Loc [ Cool_1 ]
14: End (P95) end ‘then do’
15: If (X<=>F) (P89) if cooler is on (cooler
1: 15 -- X Loc [ Cool_1 ] control location <>0)
2: 2 <>
3: 0 F
4: 30 Then Do then
11

SDM-CD16D 16 Channel Digital Control Port Expansion Module
16: If (X<=>F) (P89) check lower threshold to
1: 1 -- X Loc [ Temp_1 ] see if cooler should be
2: 4 < turned off
3: 24.5 F
4: 30 Then Do
17: Z=F (P30) if cooler should be turned off
1: 0 F put a ‘0’ into cooler control
2: 0 Exponent of 1 location
3: 15 -- Z Loc [ Cool_1 ]
18: End (P95) end ‘then do’
19: Else (P94) else, if cooler is off
20: Z=F (P30) put a ‘0’ into cooler
1: 0 F control location
2: 0 Exponent of 10
3: 15 -- Z Loc [ Cool_1 ]
21: End (P95) end ‘then do/else’
End cooler control logic
Start fan control logic based on heater/cooler
22: If (X<=>F) (P89) if heater is on
1: 10 -- X Loc [ Heat_1 ]
2: 2 <>
3: 0 F
4: 11 Set Flag 1 High set flag 1
23: If (X<=>F) (P89) if cooler is on
1: 15 -- X Loc [ Cool_1 ]
2: 2 <>
3: 0 F
4: 11 Set Flag 1 High set flag 1
24: If Flag/Port (P91) if flag 1 is set
1: 11 Do if Flag 1 is High
2: 30 Then Do then
25: Z=F (P30) put a ‘1’ into fan control
1: 1 F location
2: 0 Exponent of 10
3: 20 -- Z Loc [ Fan_1 ]
26: Else (P94) else, if flag 1 is reset
27: Z=F (P30) put a ‘0’ into fan control
1: 0 F location
2: 0 Exponent of 10
3: 20 -- Z Loc [ Fan_1 ]
12

SDM-CD16D 16 Channel Digital Control Port Expansion Module
28: End (P95) end ‘then do/else’
29: Do (P86) reset flag 1
1: 21 Set Flag 1 Low
30: End (P95) end master loop
End fan control logic based on heater/cooler
Start fan control logic based on time
31: If time is (P92) if 5 minutes remain
1: 10 Minutes (Seconds --) into a out of 15 minute
2: 15 Interval (same units as above) interval
3: 12 Set Flag 2 High set flag 2
32: If Flag/Port (P91) if flag 2 is set
1: 12 Do if Flag 2 is High
2: 30 Then Do then
33: Beginning of Loop (P87) start fan loop
1: 0 Delay
2: 5 Loop Count
34: Z=F (P30) put a ‘1’ into fan control
1: 1 F location
2: 0 Exponent of 10
3: 20 -- Z Loc [ Fan_1 ]
35: End (P95) end fan loop
36: End (P95) end’ then do’
37: If time is (P92) reset flag 2 at the
1: 0 Minutes (Seconds --) into a end of the 15 minutes
2: 15 Interval (same units as above)
3: 22 Set Flag 2 Low
End fan control logic based on time
Input locations 10 to 24 are now loaded with a ‘1’ or ‘0’ to set ports on the SDM-CD16D
38: SDM-CD16 / SDM-CD16D (P104) send instructions to the
1: 1 Reps SDM-CD16D with address 00
2: 00 Address
3: 10 Loc [ Heat_1 ]
*Table 2 Program
02: 0.0000 Execution Interval (seconds)
13

SDM-CD16D 16 Channel Digital Control Port Expansion Module
*Table 3 Subroutines
End Program
-Input Locations-1
Temp_1 7 4 0
2 Temp_2 10 0 0
3 Temp_3 10 0 0
4 Temp_4 10 0 0
5 Temp_5 18 0 0
6 _________ 0 0 0
7 _________ 0 0 0
8 _________ 0 0 0
9 _________ 0 0 0
10 Heat_1 7 3 3
11 Heat_2 11 1 0
12 Heat_3 11 1 0
13 Heat_4 11 1 0
14 Heat_5 19 1 0
15 Cool_1 7 3 3
16 Cool_2 11 1 0
17 Cool_3 11 1 0
18 Cool_4 11 1 0
19 Cool_5 19 1 0
20 Fan_1 7 1 3
21 Fan_2 11 1 0
22 Fan_3 11 1 0
23 Fan_4 11 1 0
24 Fan_5 19 1 0
25 _________ 1 1 0
26 _________ 0 0 0
27 _________ 0 0 0
28 _________ 0 0 0
29 _________ 0 0 0
14

This is a blank page.

Campbell Scientific Companies
Campbell Scientific, Inc. (CSI)
815 West 1800 North
Logan, Utah 84321
UNITED STATES
www.campbellsci.com
[email protected]
Campbell Scientific Africa Pty. Ltd. (CSAf)
PO Box 2450
Somerset West 7129
SOUTH AFRICA
www.csafrica.co.za
[email protected]
Campbell Scientific Australia Pty. Ltd. (CSA)
PO Box 444
Thuringowa Central
QLD 4812 AUSTRALIA
www.campbellsci.com.au
[email protected].au
Campbell Scientific do Brazil Ltda. (CSB)
Rua Luisa Crapsi Orsi, 15 Butantã
CEP: 005543-000 São Paulo SP BRAZIL
www.campbellsci.com.br
[email protected]
Campbell Scientific Canada Corp. (CSC)
11564 - 149th Street NW
Edmonton, Alberta T5M 1W7
CANADA
www.campbellsci.ca
[email protected]
Campbell Scientific Ltd. (CSL)
Campbell Park
80 Hathern Road
Shepshed, Loughborough LE12 9GX
UNITED KINGDOM
www.campbellsci.co.uk
[email protected]
Campbell Scientific Ltd. (France)
Miniparc du Verger - Bat. H
1, rue de Terre Neuve - Les Ulis
91967 COURTABOEUF CEDEX
FRANCE
www.campbellsci.fr
[email protected]
Campbell Scientific Spain, S. L.
Psg. Font 14, local 8
08013 Barcelona
SPAIN
www.campbellsci.es
[email protected]
Please visit www.campbellsci.com to obtain contact information for your local US or International representative.