Camtree Power V2 User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Power V2 Sucon Mount Camera Gripper (G-PM-01)
Assembly Manua l
Aluminum Rods
5x Rubber Grippers
3x Ball Tilt Head 2 x Rope Hooks
75mm Bowl
Head
Camera Mounng
Plaorm
2x Ropes
1/4” & 3/8”
Camera Mounng
Bolt Hard Case

2
 Sucon cup mounts can be axed to just
about any smooth surface on any vehicle.
Large pin on the side of each unit, sucon
mounts are good to go.
 Screw in the Ball Tilt Head on sucon cups.
Adjustable Ball Tilt Heads allow for an
extensive range of lockable posions for
Aluminum Rods.
Gripper Setup
 Three adjustable length legs screw into the
adjustable locking ball lt heads at top of the
3 sucon cup mounts.
 Tighten the knob of Ball Tilt Head to lock the
rods in a posion.
 Screw in camera mounng plaorm to Rods.
NOTE: Three rods are provided for each length - 3”, 6” & 12”. These rods can be linked together in any
combinaon you need to create the perfect setup.

3
 Now x both sucon cup with metal loops on
your vehicle.
 Aach one end of Rope with metal Hooks to
camera mounng plaorm and another end
to Metal loop of Sucon cup. Tighten the
Rope properly.
 Now loosen the four Allen bolts on Camera
plaorm, align 75mm bowl with it.
 Re-insert the bolts and ghten with Allen key
properly.
 Now mount your Fluid Head (Not Included)
on Bowl Head. And then secure your camera
set up on uid head.
 To use Rope Hooks, press lever to loosen the
rope. Remove metal hook from Metal loop of
sucon cups.

4
 Aach Rope Hooks to your vehicle, then
aach metal hooks to Rope Hooks and
ghten rope properly to secure your gripper.
 You can also aach your camera set up
directly to camera mounng plaorm with
provided screw.
 The Camera mounng plaorm of Power Mount Gripper has three leg aachment points that are each
ed with two posive locking ratchet joints, one for lt and one for swivel. Each locking ratchet joint
has a quick turn knurled lock ring for easy adjustment. You can unlock and lock each joint with a slight
twist.
 To adjust lt or swivel of each leg, rst make sure lock ring on the appropriate joint is in the UNLOCK
posion, then adjust posion of the leg as per need. And then turn lock ring back in the LOCK direcon
so that the camera won’t shake from joint movement while the vehicle is in moon.
Swivel Adjustments
Tilt Adjustments

5
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.
YOUR CAMTREE POWER V2 SUCTION MOUNT CAMERA GRIPPER
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)