Canon PIXMA iP8720 User manual

Getting Your Printer
Back On Your Network
After A Router Or Network Change
PIXMA iP8720
Windows OS
1

Getting Your Printer
Back On Your Network
After A Router Or Network Change
PIXMA iP8720
Windows OS
Preparing to Connect My Printer to the Network 3
Network Requirements 3
Notes on Wireless Connection 4
Installing the Drivers & Software 5
2

Important
If any of the following situations exist
•You have replaced your Router or Access Point
•You want to use a different wireless network
•Router settings have been changed.
Please complete the following steps to apply the new configuration settings to your printer.
3
<< Previous Next >>
Information

Preparing to Connect the printer
To the Network
Network Requirements
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is
complete, and that the computer is connected to the network.
Wireless Connection
Before connecting the machine to the network, the computer needs to be connected to the network. Make sure that
configuration of the computer and access point or router is complete.
4

Preparing to Connect the printer
To the Network
5
Notes on Network Connection
•The configuration, router functions, setup procedures and security settings of
the network device vary depending on your system environment. For details,
refer to your device's instruction manual or contact its manufacturer.
•In an office setup, consult your network administrator
•If you connect to a network that is not protected with security measures, there
is a risk of disclosing data such as your personal information to a third party.
•Place the machine and computer on the same network segment.
An "Ad-hoc connection," which establishes a direct
connection to the computer over a wireless connection
without using an access point, is not supported.

Software Installation
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk.
Installation time varies depending on the computer environment or the number of application software to be installed.
Installing the Drivers & Software
6
IMPORTANT
•Log on as the administrator (or a member of the Administrators group).
•Quit all running applications before installation.
•Do not switch users during the installation process.
•Internet connection may be required during the installation. Connection fees may apply. Consult the internet service provider.
•It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and do not remove the
Setup CD-ROM during restarting. The installation resumes once your computer has restarted.
•If the firewall function of your security software is turned on, a warning message may appear that Canon software is attempting to access
the network. If such a warning message appears, set the security software to always allow access.

Installing the PIXMA iP8720 on Your Wireless Network
When you reinstall your printer on your network because of a router or network change, you follow the same procedure as for a first time
install. A step-by-step walk through of the wireless setup is built in to the installation routine of the software that shipped with your PIXMA.
Insert the Setup CD-ROM * that came with your printer into your CD-ROM drive and proceed through the easy to follow instructions
If the following screen appears, click Start Setup Again
Connecting to the Wireless Network
7
<< Previous Next >>

Installing the Drivers & Software
8
The setup program will start automatically. The setup instructions presented in this document describe the “Cableless Setup” method
which does not require the need to know the SSID (network name), or network passphrase and does not require the printer to be temporarily
connected to the computer with a USB cable.
The Cableless Setup is not supported in Windows XP. For Windows XP Users: Use the “ Wireless Setup Using the USB Cable” method ,
whereby a USB cable is temporarily connected between the printer and computer during setup.
*If you don’t have or cannot use the Setup CD-ROM, follow the steps below to start the setup.
•Access the IJ setup site
•Read the Product Setup instructions, then click Download
•Double-click the downloaded file.
If the User Account Control dialog box appears during the setup, click Yes or Continue.

Installing the Drivers & Software
99
After starting the setup, follow on-screen instructions until the 2-1 Printer Setup screen. Click Connect to the Network

Installing the Drivers & Software
1010
Select Cableless setup on the 3-1 Setup Procedure Selection screen.

Installing the Drivers & Software
1111
Continue to follow on-screen instructions.
As directed in the 4-1 Connection via Cableless setup screen, hold down the Wi-Fi button on the printer until the POWER lamp flashes twice,
then release the Wi-Fi button

Installing the Drivers & Software
1212
Carefully follow the instructions on the Connection via Cableless setup screen. (4-2). Click Next

Installing the Drivers & Software
1313
Continue following on-screen instructions. On the Software Installation List, select *software to install and click Next.
*MP Drivers is required and cannot be deselected. We recommend installing My Image Garden and Quick Menu to take full
advantage of the printer’s features.

Installing the Drivers & Software
1414
Continue following on-screen instructions.
When the Setup Completion dialog box appears, click Complete.
At this point, setup of the printer and network is complete. Continue to follow any remaining on-screen instructions to finish and exit
the setup program.