Canon PIXMA MX410 Series User manual

Getting Your Multifunction
Back On Your Network
After A Router Or Network Change
PIXMA MX410
Windows OS
1

If any of the following situations exist, you will need to
Uninstall and Re-Install the MP Drivers
•You have replaced your Router or Access Point
•You want to use a different wireless network
•Router settings have been changed.
2

Uninstalling and Re-installing Your Multifunction
to Your Network
PIXMA MX340
Windows OS
Uninstalling the Multifunction Drivers 4
Preparing to Connect My Multifunction to My Network 6
Network Requirements 6
Important Information You Need Before Adding Your Multifunction 7
Downloading & Installing the Drivers 8
Download the Driver 8
Installing the Driver 10
3

Note: Login as a user with Administrator privileges to uninstall . Turn off any programs running in the background, such as
antivirus programs and firewalls before beginning.
Uninstalling the Multifunction Drivers
4
1. Select 'All Programs' (for Windows XP / Vista / 7)
from the Start menu.
2. Select the name of the printer model to remove and
select 'MP Drivers Uninstaller.‘

3. When the MP Drivers Uninstaller window is
displayed, click 'Execute.‘
Uninstalling the Multifunction Drivers
5
4. When the confirmation window is displayed, click
'Yes.'
5. When the Uninstallation Complete window is
displayed, click 'Complete.'

Network Requirements
Before connecting the machine to the network, make sure that configuration of the computer and access point or router is
complete, and that the computer is connected to the network.
Notes on Network Connection
•The configuration, router functions, setup procedures and security settings of the network device vary depending on your
system environment. For details, refer to your device's instruction manual or contact its manufacturer.
•The machine cannot be used over a wireless and wired connection at the same time.
Wireless Connection
Connect to your network environment over a wireless connection.
Preparing to Connect My Multifunction
To My Network
6

Preparing to Connect My Multifunction
To My Network
Be sure to prepare an access point.
Important Information You Need Before Adding Your Multifunction
The following information is required to connect to your access point or router.
•Access Point Name/Network Name:
Also referred to as SSID. A name to identify the specific access point.
•Network Key:
Also referred to as encryption key, WEP key or WPA/WPA2 passphrase, Pre-Shared key.
A password required to set to prevent unauthorized access to communication.
Check your access point or router for the following information, and then write it down.
NOTE: For details on how to check the following information, refer to the manual of your access point or router, or contact its manufacturer.
An "Ad-hoc connection," which establishes a direct
connection to the computer over a wireless connection
without using an access point, is not supported.
7

Downloading and Installing the Drivers
Downloading the Driver
To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk. The
installation process takes about 20 minutes. (The installation time varies depending on the computer environment or the number of applications
to be installed.)
8
Step One
Go to the Canon USA web site
Click here to go to MX410 Drivers & Downloads
Step Two
In the Drivers / Software Selection section, select your operating system in the Operating System dropdown menu.
Step Three
Under the Drivers tab, click the Select box for the MX410 series MP Driver Ver. 1.02 (Windows), then click the Download button.

Step One
Click Next on the Welcome screen.
Step Two
Select your place of residence and click Next.
Installing the Driver
NOTE: If a User Account Control screen appears, click Continue or Yes (depending on Windows version) to continue.
NOTE: If the same screen reappears in subsequent steps, click Continue or Yes.
Downloading and Installing the Drivers
9

Step Four
At the Connection method window, click Use the printer with
eireless LAN connection, then click Next
If the Please Allow All Install Wizard Processes screen appears,
click Next.
Installation starts. Follow any on-screen instructions to install the
software.
Step Three
Click Yes for the License Agreement.
Downloading and Installing the Drivers
10